Search Results

In this paper, experimental investigation on spray atomization and droplet dynamics inside a thermostatic expansion valve (TXV), a component commonly used in vehicle refrigeration system, was conducted. A needle and an orifice were copied from a commercial TXV and machined to be mounted inside a chamber with optical access so that the flow inside the TXV is simulated and visualized at the same time. The break-up and atomization of the refrigerant were documented near the downstream of the orifice under different feed conditions for two TXV with different geometry. A Phase Doppler Anemometry (PDA) system was used later to measure the size and velocity of atomized refrigerant droplets. The results showed that the droplet size variation along the radial direction is slightly decreased at near downstream and increased at farther downstream due to the coalescence.

Selective catalytic reduction (SCR) of NOx is coming into worldwide use for automotive diesel emissions control. To meet the most stringent standards, NOx conversion efficiency must exceed 80% while NH3 emissions or slip must be kept below 10-30 ppm. At such high levels of performance, non-uniformities in ammonia-to-NOx ratio (ANR) at the converter inlet can limit the achievable NOx reduction. Despite its significance, this effect is frequently ignored in 1D catalyst models. The corresponding model error is important to system integration engineers because it affects system sizing, and to control engineers because it affects both steady-state and dynamic SCR converter performance. A probability distribution function (PDF) based method is introduced to include mixture non-uniformity in a 1D, real-time catalyst model.

With the development of advanced ABE fermentation technology, the volumetric percentage of acetone, butanol and ethanol in the bio-solvents can be precisely controlled. To seek for an optimized volumetric ratio for ABE-diesel blends, the previous work in our team has experimentally investigated and analyzed the combustion features of ABE-diesel blends with different volumetric ratio (A: B: E: 6:3:1; 3:6:1; 0:10:0, vol. %) in a constant volume chamber. It was found that an increased amount of acetone would lead to a significant advancement of combustion phasing whereas butanol would compensate the advancing effect. Both spray dynamic and chemistry reaction dynamic are of great importance in explaining the unique combustion characteristic of ABE-diesel blend. In this study, a semi-detailed chemical mechanism is constructed and used to model ABE-diesel spray combustion in a constant volume chamber.

Hydrogen fuel is a future energy to solve the problems of energy crisis and environmental pollution. Hydrogen internal combustion engines can combine the advantage of hydrogen without carbon pollution and the main basic structure of the traditional engines. However, the power of the port fuel injection hydrogen engines is smaller than the same volume gasoline engine because the hydrogen occupies the volume of the cylinder and reduces the air mass flow. The turbocharger can increase the power of hydrogen engines but also increase the NOx emission. Hence, a comprehensive controlling strategy to solve the contradiction of the power, BTE and NOx emission is important to improve the performance of hydrogen engines. This paper shows the controlling strategy for a four-stroke, 2.3L hydrogen engine with a turbocharger. The controlling strategy divides the operating conditions of the hydrogen engine into six parts according to the engine speeds and loads.

The modeling of fuel jet atomization is key in the characterization of Internal Combustion (IC) engines, and 3D Computational Fluid Dynamics (CFD) is a recognized tool to provide insights for design and control purposes. Multi-hole injectors with counter-bored nozzle are the standard for Gasoline Direct Injection (GDI) applications and the Spray-G injector from the Engine Combustion Network (ECN) is considered the reference for numerical studies, thanks to the availability of extensive experimental data. In this work, the behavior of the Spray-G injector is simulated in a constant volume chamber, ranging from sub-cooled (nominal G) to flashing conditions (G2), validating the models on Diffused Back Illumination and Phase Doppler Anemometry data collected in vaporizing inert conditions.

Recently, with the increasing interest on some potential alternative substitutes of petroleum fuels such as biodiesel and butanol, more and more researches are focused on the field of bio-fuels because they are renewable and friendly to the environment and can possibly reduce domestic demand on foreign petroleum. Bio-fuels are generally used in the commercial market by mixing with petroleum-based diesel or gasoline. Since the volatilities and boiling points of ethanol/butanol and diesel/biodiesel fuels are significantly different, micro-explosion can be expected in the blend mixture. In this study, a numerical model of micro-explosion including bubble generation, bubble expansion, and final breakup for multi-component bio-fuel droplets is proposed. From the simulated results of droplet characteristics at the onset of micro-explosion, it is concluded that micro-explosion is possible under engine operation condition for ethanol/butanol-diesel/biodiesel fuel blends.

The combustion and emission characteristics of a diesel engine running on butanol-diesel blends were investigated in this study. The blending ratio of n-butanol to diesel was varied from 0 to 40 vol% using an increment of 10 vol%, and each blend was tested on a 2.7 L V6 common rail direction injection diesel engine equipped with an EGR system. The test was carried out under two engine loads at a constant engine speed, using various combinations of EGR ratios and injection timings. Test results indicate that n-butanol addition to engine fuel is able to substantially decrease soot emission from raw exhaust gas, while the change in NOx emissions varies depending on the n-butanol content and engine operating conditions. Increasing EGR ratio and retarding injection timing are effective approaches to reduce NOx emissions from combustion of n-butanol-diesel blends.

A finite diffusion method is presented in this paper to model droplet evaporation for complex liquid mixture composed of different homogeneous groups. Multiple components fuel mixture is represented by separate distribution functions to describe the composition of each homogeneous group in the mixture. Only a few parameters are required to describe the mixture. Quasi-steady assumption is applied in the determination of evaporation rates and heat flux to the droplet, and the effects of surface regression, finite diffusion and preferential vaporization of the mixture are included in the liquid phase equations using an effective properties approach. The proposed model was validated by comparing against experimental measurements for single, isolated droplets of n-decane, kerosene, heptane-decane and diesel-butanol. The present model was applied to simulate the evaporation of isolated droplets with composition of typical diesel.

This paper focuses on the spray and atomization characteristics of a Dual-Fuel Injector (DFI) which includes a primary and a secondary fuel inlet. Three injectors were analyzed in this study. Apart from the DFI, two conventional diesel injectors were tested as baselines for comparison - a piezo-electric and a solenoid injector. The rail pressures ranged from 200 - 500 bar for the conventional injectors. The DFI was tested first as a single-fuel injector (by sealing the secondary inlet) at pressures ranging from 100 - 300 bar, and then in its dual-fuel mode with the primary inlet pressure ranging from 100 - 300 bar, and the secondary inlet at 25 bar higher than the primary pressure. Injection duration of 0.5 ms was chosen for the experiment. High-speed Mie scattering images were recorded to capture the spray evolution. Phase Doppler Anemometry (PDA) measurements were conducted at different locations in the spray for the acquisition of droplet sizes and velocity distributions.

For the parallel hybrid electric vehicles in which there are one engine and one motor, and the motor is located before the transmission, the motor torque is added as a new parameter to develop a new shift strategy for automated manual transmissions. The design rule of the shift strategy is to pursue a better fuel economy without sacrificing performance of the vehicle. Upshift strategies in four driving modes and downshift strategies in driving mode and in braking mode are discussed in detail respectively. Simulations show that the new three-parameter shift strategy is able to save fuel consumption in driving mode and regenerate more energy in braking mode.

An optically accessible single-cylinder high-speed direct-injection (HSDI) diesel engine equipped with a Bosch common rail injection system was used to study effects of injection pressures on the in-cylinder spray and combustion processes. An injector with an injection angle of 70 degrees and European low sulfur diesel fuel (cetane number 54) were used in the work. The operating load was 2.0 bar IMEP with no EGR added in the intake. The in-cylinder pressure was measured and the heat release rate was calculated. High-speed Mie-scattering technique was employed to visualize the liquid distribution and evolution. High-speed combustion video was also captured for all the studied cases using the same frame rate. NOx emissions were measured in the exhaust pipe. The experimental results indicated that for all of the conditions the heat release rate was dominated by a premixed combustion pattern. Two-stage low temperature reaction was seen for early injection timings.

A single nozzle port fuel injector was modified to apply electrostatic charge to the fuel stream, with the intention of studying electrostatically assisted sprays in a practical, port-injected engine. The modifications were kept external to the injector and involved placing an electrode and insulating liner over the tip of the injector. The performance of the modified injector, which combined pressure driven and electrostatic atomization, was characterized in three phases: the injector sprays themselves were studied, combustion of charged fuel droplets was studied, and the injector was installed and tested on a single cylinder spark ignition engine. In the first phase, Fraunhofer diffraction measurements of droplet size, and particle image velocimetry measurements of droplet velocity were performed. The charge transferred by the sprays was measured using an electrometer, and typical forces exerted on droplets in the sprays were estimated.

Logic threshold control algorithm for parallel hybrid electric power train is presented systematically, in which engine operation points are limited within higher efficient area by logic threshold control algorithm targeting fuel economy. The off-line simulation model of parallel HEV power train is developed which includes sub-models of logic threshold control system and controlled objective (such as engine, electric motor, battery pack and so on). The debug and validation of logic threshold control algorithm is completed on developed modular test facility. The results show that the simple and practical logic threshold control algorithm can effectively limited engine operation points and much more fuel economy can be achieved than that of conventional ICE power train.

Utilizing the developed off-line simulation model of series hybrid power train the study on the influence of components' parameters on acceleration performance and fuel economy of transit bus is completed. Based on these the guideline strategies of parametric design of series hybrid power train for transit bus are brought forward in this paper. Given the condition of propulsion requirement the parametric design for this transit bus are performed targeting minimizing fuel consumption. It is conclusion that the appropriate components' parameters determined by means of parametric design can make series hybrid transit bus achieve much better acceleration performance and much lower fuel equivalent consumption than that of baseline transit bus.

Developed control algorithm for series hybrid electric power train is presented systematically, which keeps engine operation points on the locus of highest efficiency torque/speed points using a lookup table defined by engine power and speed. The off-line simulation model of series hybrid power train is developed which includes sub-models of control system and controlled objective (such as engine, motor, battery pack and so on). The debug and validation of control algorithm is performed on developed modular test facility. The results show that developed control algorithm can effectively keep engine operating on the locus of high efficiency points and much more fuel economy can be achieved than that of conventional ICE power train, meanwhile battery SOC can be maintained within reasonable level without charging outside during cycles.

In concept design and prototype development of parallel hybrid power train for transit bus one of the main concerns is to determine the appropriate parameters of power train components. Utilizing the developed off-line simulation model of parallel hybrid power train the study on the influence of components' parameters on acceleration performance and fuel economy of transit bus is completed. Based on these the guideline strategies of parametric design of parallel hybrid power train for transit bus are brought forward in this paper. Given the condition of propulsion requirement the parametric design for this transit bus are performed targeting minimizing fuel consumption. It is conclusion that the appropriate components' parameters determined by means of parametric design can make parallel hybrid transit bus achieve much better acceleration performance and much lower fuel equivalent consumption than that of baseline transit bus.

HCCI/PCCI combustion concepts have been demonstrated for both high brake thermal efficiency and low engine-out emissions. However, these advanced combustion concepts still could not be fully utilized partially due to the limitations of conventional fixed spray angle nozzle designs for issues related to wall wetting for early injections. The micro-variable circular orifice (MVCO) fuel injector provides variable spray angles, variable orifice areas, and variable spray patterns. The MVCO provides optimized spray patterns to minimize combustion chamber surface-wetting, oil dilution and emissions. Designed with a concise structure, MVCO can significantly extend the operation maps of high efficiency early HCCI/PCCI combustion, and enable optimization of a dual-mode HCCI/PCCI and Accelerated Diffusion Combustion (ADC) over full engine operating maps. The MVCO variable spray pattern characteristics are analyzed with high speed photographing.

In this work, an efficient and unified combustion model is introduced to simulate the flame propagation, diffusion-controlled combustion, and chemically-driven ignition in both SI and CI engine operation. The unified model is constructed upon a G-equation model which addresses the premixed flame propagation. The concept of the Livengood-Wu integral is used with tabulated ignition delay data to account for the chemical kinetics which is responsible for the spontaneous ignition of fuel-air mixture. A set of rigorously defined operations are used to couple the evolution of the G scalar field and the Livengood-Wu integral. The diffusion-controlled combustion is simulated equivalent to applying the Burke-Schumann limit. The combined model is tested in the simulation of the premixed SI combustion in a constant volume chamber, as well as the CI combustion in a conventional small bore diesel engine.

Dual-fuel combustion combining a premixed charge of compressed natural gas (CNG) and a pilot injection of diesel fuel offer the potential to reduce diesel fuel consumption and drastically reduce soot emissions. In this study, dual-fuel combustion using methane ignited with a pilot injection of No. 2 diesel fuel, was studied in a single cylinder diesel engine with optical access. Experiments were performed at a CNG substitution rate of 70% CNG (based on energy) over a wide range of equivalence ratios of the premixed charge, as well as different diesel injection strategies (single and double injection). A color high-speed camera was used in order to identify and distinguish between lean-premixed methane combustion and diffusion combustion in dual-fuel combustion. The effect of multiple diesel injections is also investigated optically as a means to enhance flame propagation towards the center of the combustion chamber.

A new approach of NOx reduction in the compression-ignition engine is introduced in this work. The previous research has shown that during the combustion stage, the high temperature ignition tends to occur early at the near-stoichiometric region where the combustion temperature is high and majority of NOx is formed; Therefore, it is desirable to burn the leaner region first and then the near-stoichiometric region, which inhibits the temperature rise of the near-stoichiometric region and consequently suppresses the formation of NOx. Such inverted ignition sequence requires mixture with inverted phi-sensitivity. Fuel selection is performed based on the criteria of strong ignition T-sensitivity, negligible negative temperature coefficient (NTC) behavior, and large heat of vaporization (HoV).