Search Results

This paper sets up a simplified dynamic model for simulating the yaw/roll stability of heavy tractor-semitrailer using Matlab/Simulink. A linear quadratic regulator (LQR) based on partial-state feedback controller is used to optimize the roll stability of the vehicle. The control objective for optimizing roll stability is to be reducing the lateral load transfer rate while keeping the suspension angle less than the maximum allowable angle. The simulation result shows that the LQR controller is effective in the active roll stability control of the heavy tractor-semitrailer.

This paper introduces the characteristics of the 4 wheel independent driving/4 wheel independent steering (4WID/4WIS) electric vehicle (EV). Models of Subsystems and the vehicle are constructed based on Matlab/simulink. The vehicle model allows the inputs of different drive torques and steer angles of four wheels. The dynamic characteristics of drive motors and steer motors are considered, and also it can reflect the vehicle longitudinal dynamics change due to the increase of the mass and inertia of the four wheels. Besides, drive mode selection function that is unique to this type vehicle is involved. Simulations and analyses of crab, oblique driving and zero radius turning which are the special conditions of 4WID/4WIS EV are conducted. The results show that the model can reflect the dynamic response characteristics. The model can be used to the simulation analyses of handling, stability, energy saving and control strategies verification of 4WID/4WIS EVs.

This essay aims to develop an electrically controlled steering test bench and lay a solid foundation for the development of steering system. The first part mainly introduces the function, structure and working principle of the test bench. For the hardware system, it includes the steering system, fixture, sensors as well as a frameless disk motor for carrying out automatic motor input, and a dual linear motor system selected as the road resistance simulation actuator. As for the software, MATLAB/Simulink, CarSim, RTI and ControlDesk are used. Therefore, with the help of real-time simulation platform, researchers can not only build control strategy and dynamic model but also control the experiment and tune parameters in real-time. The second part of the essay aims to identify both electric and mechanical parameters of R-EPS system by carrying out tests on the proposed test bench. As parameters are successfully identified, the feasibility of the test bench is also verified.

The simulation of electro-pneumatic components used in brake systems of commercial vehicles is of great importance in order to understand their characteristics for developing a control logic and improve the braking performance. As the goal of improving the performance of the commercial vehicle pneumatic EBS(Electronically controlled Braking System), static and dynamic characteristics of proportional relay valve for commercial vehicle pneumatic EBS have been simulated by using MATLAB/Simulink environment and validated by testing on hardware-in-the-loop test bench focused on its pressure hysteresis characteristic. The simulation and test results show that the mathematic model for proportional relay valve characteristics is reasonable and reliable, and this simulation tool can be used for research and developing of pneumatic EBS system for commercial vehicle effectively.

In order to improve the braking energy recovery, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established by co-simulation platform for the TruckSim and Matlab/Simulink in this paper. EBS makes the front and rear shaft braking force arbitrarily distributed, which is more effective to improve the rate of energy recovery and the braking stability. A braking force distribution algorithm for hybrid electric bus based on EBS was designed in this paper. Under the premise to meet the driver's needs and the ECE regulations, this braking force distribution method focuses on making the braking force distribute to the drive shaft to a maximum extent, so as to obtain the maximum energy recovery rate by the utilization of the motor regenerative braking. At last, the simulation in different operating conditions was used to analyze the braking energy utilization and the braking performance based on the simulation model.

In order to improve the braking energy recovery and ensure the braking comfort, a new type of regenerative braking coordinated control algorithm is designed in this paper. The hierarchical control theory is used to the regenerative braking control algorithm. First, the front axle braking force and rear axle braking force are distributed. Then the rear axle motor braking force and mechanical braking force are distributed. Finally, the dynamic coordinated control strategy is designed to control pneumatic braking system and motor braking system. Aimed at keeping the fluctuation of the total braking force of friction and the regenerative braking force small during braking modes switch, a coordinated controller was designed to control the pneumatic braking system to compensate the error of the motor braking force. Based on Matlab/Simulink platform, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established.

Four-wheel independent drive EV is driven by four brushless DC motors which are embedded in the wheel hubs. It enables each wheel's driving torque to be controlled independently. Due to the motors' torque and rotational speed easily measured, as well as the features of fast response and precise control, the EV enjoys obvious advantages over traditional vehicles in acceleration slip regulation. In this paper a novel acceleration slip regulation strategy for four-wheel independent drive EV is studied. The strategy includes a road identification module for the peak value of road adhesion coefficient and a slip regulation logic based on PID algorithm. Through comparing the current wheel slip ratio and the utilized adhesion coefficient with the typical roads' value, the identification module adopts the fuzzy control algorithm to recognize the similarity between the current road and the typical roads. Utilizing the similarity we can calculate the optimal slip ratio of the current road.

This paper presents an adaptive observer-based approach for the combined state estimation and active fault detection and isolation (FDI) of the individual-wheel-drive (IWD) vehicles. A 3-DOF vehicle model coupled with the Highway Safety Research Institute (HSRI) tire model is established and used as the observation model. Based on this model, the dual unscented Kalman filter (DUKF) technique is employed for the observer design to give fusion results of the interdependent state and parameter variables, which undergo nonlinear transformations, with the minimum square errors. Effectiveness of the proposed algorithm is examined and validated through co-simulation between MATLAB/Simulink and CarSim. The results demonstrate that the DUKF-based observer effectively filters the sensor signals, accurately obtains the longitudinal and lateral velocities, explicitly isolates the faulty wheel(s) and accurately estimates the actual torque(s) even with the presence of noise.

As a new form of electric vehicle, Four-wheel-independent electric vehicle with X-By-Wire (XBW) inherits all the advantages of in-wheel motor drive electric vehicles. The vehicle steering system is liberated from traditional mechanical steering mechanism and forms an advanced vehicle with all- wheel independent driving, braking and steering. Compared with conventional vehicles, it has more controllable degrees of freedom. The design of the integrated vehicle dynamics control systems helps to achieve the steering, driving and braking coordinated control and improves the vehicle's handling stability. In order to solve the problem of lacking of vehicle state information in the integrated control, some methods are used to estimate the vehicle state of four-wheel-independent electric vehicles with XBW. In order to improve the estimation accuracy, unscented Kalman filter (UKF) is used to estimate the vehicle state variables in this paper.