Search Results

A three-dimensional model for premixed- charge naturally-aspirated rotary engine combustion is used to identify combustion chamber geometries that could lead to increased indicated efficiency for a lean (equivalence ratio =0.75) natural gas/air mixture. Computations were made at two rpms (1800 and 3600) and two loads (approximately 345 Kpa and 620 Kpa indicated mean effective pressure). Six configurations were studied. The configuration that gave the highest indicated efficiency has a leading pocket with a leading deep recess, two spark plugs located circumferentially on the symmetry plane (one after the minor axis and the other before), a compression ratio of 9.5, and an anti-quench feature on the trailing flank.

Comparisons are discussed of computed and measured transient sprays from an air-assisted fuel injector. Although the measurements were extensive, they did not characterize fully the conditions at the nozzle exit which had to be obtained from a simple model of the flow within the injector. It is found that spray width, spray tip penetration, amount of spray found in the head vortex, and chamber fuel distribution are strong functions of the internal design of the fuel injector. Particularly important are the drop size distribution and the direction of the flow at the exit of the nozzle.

The objective of this study is to characterize the operation of an air-assisted fuel injector. This characterization involves four sets of tests: fuel and air flow calibration; instantaneous measurements of fuel and air solenoid signals, internal pressure in the injector, and poppet lift; photographs of the spray; and droplet sizing. The injector poppet was designed to form a spray of 80° included angle. Nitrogen, instead of air, was used to assist the injection of unleaded gasoline into steady, compressed nitrogen at room temperature. The following conditions were used: nominal fuel flow rates of 10, 20, and 30 mm3/injection; spray chamber pressures of 0.1, 0.169, and 0.445 MPa; and nominal injections per minute (IPM) of 1600 and 3000. Results showed a linear increase in total fuel mass supplied to the injector as fuel solenoid pulse width was increased, except at the highest IPM and chamber pressure when the total fuel mass tended to level off.

Recent measurements by of gas intake flows and exhaust pressure in a motored, ported, single-cylinder engine with strong swirl and roll have been used as boundary conditions to a three-dimensional, transient computer simulation of the flow within the cylinder. For each condition, the calculation is continued over several engine cycles until the periodic solution is obtained. The computed TDC tangential velocity and turbulence intensity are then compared with measured ones. A technique is described to evaluate scavenging efficiency, the fraction of charge that remains in the cylinder over later cycles and the degree of mixedness of fresh and residual charge. For this motored ported engine, it is found that the scavenging efficiency is very low (19.4% at 1200 RPM) and the inflow from the exhaust ports is very significant. For practical ported engines with combustion, the scavenging efficiency is much higher but the inflows from exhaust ports are still expected to be significant.

A three-dimensional model for a direct injection stratified-charge rotary engine has been employed to study two modifications to the pocket geometry of the engine. In one modification, a pocket is located towards the leading edge of the rotor and is shown to produce recirculation within the pocket and faster burning. In the second modification, a two pocket rotor with two injectors and two spark plugs is studied. It appears that this should result in better utilization of the chamber air. It also appears that both modifications rhould result in higher efficiency of the direct-injected stratifiedcharge rotary engine. However extensive computations are required before a final conclusion is reached and before specific recommendations can be made.

For practical, extensive 3-D computations for engine improvements, each physical submodel needs to be the simplest that is compatible with the accuracy of all other physical submodels and of the numerics. The addition of one progress variable controlled by one Arrhenius term is shown to be adequate to reproduce Diesel ignition delay in 2-D and 3-D computations. The rest of the model is that used for years by the authors to optimize combustion in reciprocating and rotary engines with premixed and non-premixed charges, including all of its model constants. This minimal Diesel autoignition submodel reproduces well trends and magnitudes of ignition delay versus chamber temperature and pressure. As in experiments, it is found that multiple ignition sources develop in rapid succession at various locations around the fuel spray after the first ignition event.

The exciplex fluorescence technique has been used to separately visualize liquid and vapor phase fuel in engines since its development by Melton. However, as a fluorescence technique it has the potential to be quantitative and the underlying assumptions have been outlined by Melton. An initial quantitative application of the TMPD/naphthalene system, based on these assumptions, applied to a hollow-cone spray in a two-stroke engine, indicated that it substantially over-estimates the concentration of fuel vapor about TDC. The reasons for the discrepancy were investigated and it was concluded that a major factor is the effect of temperature on the photophysics of the species involved. Thus the absorption spectra of the exciplex dopants were determined at temperatures up to 700 K. These experiments showed that the increase in absorption with temperature above 500 K is responsible for the failure of the earlier calibration.

Results are presented of two-dimensional computations of air-assist fuel injection into engines with bowl-in-piston and bowl-in-head, with and without swirl and for early and late injection but without combustion. The general finding is that swirl tends to destroy the head vortex of the air/fuel jet and results in a faster collapse of the spray cone toward its axis. Faster collapse is also promoted by high density of the chamber gas (e.g. late injection) and bowl-in-head design (limited availability of chamber gas around the spray, presence of walls and delayed influence of squish by the injector). With enhanced collapse, fuel-rich regions are formed around the axis and away from the injector. With reduced collapse, the radial distribution of the fuel is more uniform. Thus swirl tends to lead to both slower vaporization and richer vapor mixtures. Also, with strong swirl the rich mixtures tend to end up by the injector; without swirl, by the piston.

Results are presented of 3-D computations of direct injection of gaseous methane and of liquid tetradecane through a multi-hole injector into a Diesel engine. The study focusses on the distribution of fuel/air ratio within the resulting gas and spray jets under typical Diesel conditions prior to ignition. It is shown that for a significant time after start of injection, the fraction of the vapor fuel which is in richer-than-flammable mixtures is greater in gas jets than in sprays. For methane injection, it is also shown that changing some of the flow conditions in the engine or going to a poppet-type injector, does not result in improved mixing. An explanation of these results is provided also through an analysis of the self-similar gas jet and 2-D computations of gas and spray jets into constant pressure gas. A scaling for time and axial distance in the self-similar gas jet also clarifies the results.

Results of experiments performed on a direct-injection two-stroke engine using an air-assisted injector are presented. Pressure measurements in both the engine cylinder and injector body coupled with backlit photographs of the spray provide a qualitative understanding of the spray dynamics from the oscillating poppet system. The temporal evolution of the spatial distribution of both liquid and vapor fuel were measured within the cylinder using the Exciplex technique with a new dopant which is suitable for tracing gasoline. However, a temperature dependence of the vapor phase fluorescence was found that limits the direct quantitative interpretation of the images. Investigation of a number of realizations of the vapor field at a time typical of ignition for a stratified-charge engine shows a high degree of cycle to cycle variability with some cycles exhibiting a high level of charge stratification.

Efforts are reported to reproduce the distribution of liquid and vapor fuel from a pulsating hollow-cone liquid-only injector measured by the planar exciplex technique within the head cup of a motored ported single-cylinder engine operated at 1600 rpm with high swirl and a squish ratio of 75%. The injector, cup and cylinder were coaxial. The measurements show that shortly after the beginning of the injection the maximum liquid and vapor fuel concentrations are along the axis but also that the spray achieves substantial radial and axial penetrations. The engine flowfield without injection had previously been characterized by LDV and PIV and so had been the injector and its spray in constant pressure environments so that little arbitrariness was left in reproducing the spray in the engine. Two spray models were used. In one the large drops produced by the break up of the liquid sheet were introduced into the numerical field at the injector exit nearly with the poppet seat angle.

A second effort is reported to reproduce the distribution of fuel from a pulsating hollow-cone liquid-only poppet injector measured by the planar exciplex technique within the head cup of a motored ported single-cylinder engine operated at 1600 rpm with high swirl and a squish ratio of 75%. The injector, cup and cylinder were coaxial. The engine flowfield without injection had previously been characterized by LDV and PIV and so had been the injector and its spray in constant pressure environments. In a previous effort, the injector was assume to generate drop and the computed collapse of the spray was found to be too slow. In this work, the injector is assumed to generate liquid sheets that change shape and produce drops from their leading edges and surfaces as they propagate through the gas.

In a previous study, the authors compared the fuel-air mixing characteristics of gas jets and sprays in Diesel engine environments in the absence of combustion. A three-dimensional model for flows and sprays was used. It was shown that mixing was slower in gas jets relative to fast-evaporating sprays. In this study, which is an extension of the previous one, the direct-injection of gasesous methane, gaseous tetradecane and liquid tetradecane are studied using the same three-dimensional model. This study concentrates on combustion. It is shown that the fuel-air mixing rate and hence the burning rate are initially slower with gas injection.

Simultaneous fuel distribution images (by shadowgraph and laser-induced fluorescence) and cylinder pressure measurements are reported for a combusting stratified-charge engine with a square cup in the head at 800 RPM and light load for two spark locations with and without swirl. Air-assisted direct-injection occurred from 130°-150° after bottom dead center (ABDC) and ignition was at 148° ABDC. The engine is ported and injection and combustion take place every 6th cycle. The complicated interaction of the squish, fuel/air jet, square cup, spark plug geometry and weak tumble gives rise to a weak crossflow toward the intake side of the engine with no swirl, but toward the exhaust side in the presence of strong swirl, skewing the spray slightly to that side.

Engine-out, cold-start (from 20°C) UHC emissions from a contemporary 2.0 4-cylinder engine with swirl control were measured with FID and FT-IR. The steady-state, end of test operation was 1500 rpm, 2.6 bar BMEP (25% load) and stoichiometric mixture. Four fuel systems were employed pintle-type port-injected gasoline, air-forced port-injected gasoline, port-injected propane, and premixed propane. These fuel systems were chosen to separate effects of fuel atomization, vaporization, and fuel-air mixing. Each system was optimized with respect to injector targeting, injection timing, mixture enrichment, and spark advance. Open-valve injection timing increased UHC emissions more with the pintle-type injector than with the air-forced, system. UHC emissions with propane injection were minimized with open valve injection.

Planar instantaneous fuel concentration measurements were made by laser-induced fluorescence of 3-pentanone in the spark gap just prior to ignition in a direct-injection spark-ignition engine operating at a light load, highly stratified condition. The distribution of the average equivalence ratio in a circle of 1.9 mm diameter centered on the spark plug showed that a large fraction of the cycles had an equivalence ratio below the lean limit, yet acceptable combustion was achieved in those cycles. Further, weak correlation was found between the local average equivalence ratio near the spark plug and the time required to achieved a 100 kPa pressure rise above the motoring pressure, as well as other parameters which characterize the early stages of combustion. The cause for this behavior is assessed to be mixture motion during the spark discharge which continually convects fresh mixture through the spark gap during breakdown.

The objective of this work was to establish whether two detergent-type additives(A and B) influence the drop size and evaporation of two Diesel fuels (1 and 2) under Diesel engine conditions. Two experiments were performed: visualization of liquid and vapor fuel by the exciplex technique in a motored single-cylinder engine and measurement of the Sauter mean diameter, total drop cross sectional area and total drop volume by laser diffraction in a spray chamber. The same Diesel injector and pump system were used in the two experiments. The engine tests were carried out using a high aromatic content fuel (1) particularly suited for the exciplex studies. These studies showed that additive A yielded a lower vapor signal than additive B, which in turn gave a lower vapor signal than untreated fuel. Spray chamber results were obtained for both fuel 1 and 2. Additive A reduced the evaporation of fuel 1 whereas additive B gave a smaller and less consistent affect.

The combustion characteristics of three gaseous fuels (hydrogen, methane and ethane) in a direct-injection stratified-charge single-cylinder engine with a centered square head-cup operated at 800 rpm (compression ratio = 10.8, squish ratio = 75%, nominal swirl ratio = 4) were studied to assess the extent to which the combustion is controlled by turbulent mixing, laminar mixing and chemical kinetics. The injection of gaseous fuels was via a Ford AFI injector, originally designed for the air-forced injection of liquid fuel. Pressure measurements in the engine cylinder and in the injector body, coupled with optical measurements of the injector poppet lift and shadowgraph images of the fuel jets provided both quantitative and qualitative information about the in-cylinder processes. To make the cases comparable, the total momentum of the fuel jets and the total heat released by the three fuels was kept the same (equivalence ratio = 0.316, 0.363, 0.329 for H2, CH4 and C2H6, respectively).

A closed-circuit television technique has been developed for the real time viewing and recording of combustion and related processes in internal combustion engines. The technique has been applied to a transparent piston, transparent head engine, and shadowgraphs of combustion chamber events have been observed and recorded. The technique is particularly suited for the study of changes in the combustion process due to variations of engine parameters such as mixture ratio, load, speed, spark timing, injection initiation, etc., since the changes can be observed and recorded at the same time that they occur. A brief and qualitative study of flame and pressure cyclic variations is reported and discussed as an example of an application for which the television technique is particularly suited.

Combustion in a divided-chamber, stratified-charge engine is considered and flame and pressure results obtained with a two-dimensional, unsteady model are compared with corresponding engine data. The model is applied to eight engine conditions differing in speed, load and size of the prechamber orifice. The model employs one overall chemical reaction rate, the k-ε representation of turbulence, and a wall heat loss proportional to the heat release. The computed results are shown to be in good agreement with the experimental ones in spite of the complexity of the problem and the early stages of detailed model validation studies. They are also shown to compare somewhat better than earlier ones obtained with an ad-hoc jet turbulence model. Both studies prove the importance of the prechamber jet to the overall combustion process for the particular engine investigated.