Search Results

This paper presents an automated driving control algorithm for the control of an autonomous vehicle. In order to develop a highly automated driving control algorithm, one of the research issues is to determine a safe driving envelope with the consideration of probable risks. While human drivers maneuver the vehicle, they determine appropriate steering angle and acceleration based on the predictable trajectories of the surrounding vehicles. Therefore, not only current states of surrounding vehicles but also predictable behaviors of that should be considered in determining a safe driving envelope. Then, in order to guarantee safety to the possible change of traffic situation surrounding the subject vehicle during a finite time-horizon, the safe driving envelope over a finite prediction horizon is defined in consideration of probabilistic prediction of future positions of surrounding vehicles.

This paper describes an Integrated Chassis Control (ICC) strategy for improving high speed cornering performance by integration of Electronics Stability Control (ESC), Four Wheel Drive (4WD), and Active Roll Control System (ARS). In this study, an analysis of various chassis modules was conducted to prove the control strategies at the limits of handling. The analysis is focused to maximize the longitudinal velocity for minimum lap time and ensure the vehicle lateral stability in cornering. The proposed Integrated Chassis Control algorithm consists of a supervisor, vehicle motion control algorithms, and a coordinator. The supervisor monitors the vehicle status and determines desired vehicle motions such as a desired yaw rate, longitudinal acceleration and desired roll motion. The target longitudinal acceleration is determined based on the driver's intention and vehicle current state to ensure the vehicle lateral stability in high speed maneuvering.

This paper presents the design and evaluation of an emergency driving support (EDS) algorithm. The control objective is to assist driver's collision avoidance maneuver to overcome a hazardous situation. To support driver, electrically controllable chassis components such as motor driven power steering (MDPS) and differential braking and surrounding sensor systems such as radar and camera are used. The EDS algorithm is designed for 3 parts: monitoring, decision, and control. The proposed EDS algorithm recognizes a collision danger using minimum lateral acceleration to avoid collision and time-to-collision (TTC) and driver's intention using sensor systems. The control mode is determined using the indices from monitoring process and the collision avoidance trajectory is derived with trapezoidal acceleration profile (TAP).

This paper describes a driving control algorithm based on a skid steering for a Robotic Vehicle with Articulated Suspension (RVAS). The RVAS is a kind of unmanned ground vehicle based on a skid steering using independent in-wheel drive at each wheel. The driving control algorithm consists of four parts: a speed controller for following a desired speed, a lateral motion controller that computes a yaw moment input to track a desired yaw rate or a desired trajectory according to the control mode, a longitudinal tire force distribution algorithm that determines an optimal desired longitudinal tire force and a wheel torque controller that determines a wheel torque command at each wheel in order to keep the slip ratio at each wheel below a limit value as well as to track the desired tire force. The longitudinal and vertical tire force estimators are required for the optimal tire force distribution and wheel slip control.

This paper presents a closed-loop evaluation of the Vehicle Stability Control (VSC) systems using a vehicle simulator. Human driver-VSC interactions have been investigated under realistic operating conditions in the laboratory. Braking control inputs for vehicle stability enhancement have been directly derived from the sliding control law based on vehicle planar motion equations with differential braking. A driving simulator which consists of a three-dimensional vehicle dynamic model, interface between human driver and vehicle simulator, three-dimensional animation program and a visual display has been validated using actual vehicle driving test data. Real-time human-in-the loop simulation results in realistic driving situations have shown that the proposed controller reduces driving effort and enhances vehicle stability.

An estimation algorithm for vehicle driving load has been proposed in this paper. Driving load is an important factor in a vehicle's longitudinal motion control. An approach using an observer is introduced to estimate driving load based on inexpensive RPM sensors currently being used in production vehicles. Also, the new torque estimation technique using neural network has been incorporated in this estimation algorithm to achieve better performance over variations in the automotive power transmissions process. The effectiveness of the observer-based method is demonstrated through the use of a nonlinear full vehicle simulation model in various scenarios. The proposed method using an observer has good performance, both over modeling error in powertrain system and under the uncertain environment of a running vehicle.

This paper presents the integrated chassis control(ICC) of four-wheel drive(4WD), electronic stability control(ESC), electronic control suspension(ECS), and active roll stabilizer(ARS) for limit handling. The ICC consists of three layers: 1) a supervisor determines target vehicle states; 2) upper level controller calculates generalized forces; 3) lower level controller, which is contributed in this paper, optimally allocates the generalized force to chassis modules. The lower level controller consists of two integrated parts, 1) longitudinal force control part (4WD/ESC) and 2) vertical force control part (ECS/ARS). The principal concept of both algorithms is optimally utilizing the capability of the each tire by monitoring tire saturation, with tire combined slip. By monitoring tire saturation, 4WD/ESC integrated system minimizes the sum of the tire saturation, and ECS/ARS integrated system minimizes the variance of the tire saturation.

This paper presents an integrated chassis control method for vehicle stability under various road friction conditions without information on tire-road friction. For vehicle stability, vehicle with an integrated chassis control needs to cope with the various road friction conditions. One of the chassis control method under various road conditions is to determine and/or limit control inputs based on tire-road friction coefficient. The tire-road friction coefficient, however, is difficult to estimate and still a challenging task. The key idea for the proposed method without the estimation of the tire-road friction coefficient is to analyze and control vehicle states based on a tire slip angle - tire force phase plane, i.e. based on these vehicle responses: tire forces and tire slip angles of front/rear wheels.

This paper describes a lane departure avoidance system to help the driver avoid the lane departure during drowsiness or inattention. The lane departure avoidance system proposed in this paper consists of unintended lane departure decision part, upper level controller part and lower level controller part. The index used in unintended lane departure decision part is proposed to monitor a driver's intention with steering behaviors. The desired dynamics is calculated in upper level controller part. When the desired dynamics is calculated, it is considered to guarantee a driver's safety and smooth ride feel simultaneously as possible. The lower level controller distributes the desired control input to actuators, motor driven power steering (MDPS) module and vehicle stability control (VSC) module. The proposed lane departure avoidance system has been evaluated via human driver model-in the loop simulation.

This paper describes a driving motor torque distribution strategy of six-wheel-driven electric vehicles for optimized energy consumption. In this research, this strategy minimizes motoring power consumption and maximizes regenerative braking power under given required power condition. The torque distribution controller consists of total required motor torque calculation part, upper and optimal torque calculation part, lower level controller. The upper level controller determines total required torque of vehicle. And the torque is determined by acceleration pedal input of driver and vehicle velocity. The lower level controller calculates energy consumption in given condition and distributes motor torque to driving motor minimizing energy consumption. In distributing optimal motor torque, it is important to get accurate characteristics of driving motor and performance constraint.

This paper presents an integrated control of in-wheel motor (IWM) and electronic limited slip differential (eLSD) to enhance the vehicle lateral stability and maneuverability. The two actuators are utilized in the proposed controller to achieve separate purposes. The IWM controller is designed to modify the understeer gradient for enhanced handling characteristic and maneuverability. The eLSD controller is devised to improve the lateral stability to prevent oversteer in a severe maneuver. The proposed controller consists of a supervisor, upper-level controller and lower-level controller. The supervisor determines a target motion based on a target understeer gradient for IWM control and a yaw rate reference for eLSD control. The upper-level controller generates a desired yaw moment for the target motion. In the lower-level controller, the desired yaw moment is converted to the control inputs for IWMs in the two front wheels and eLSD at the rear axle.

This paper is concerned with the torque distribution problem including slip limitation and actuator fault tolerance to improve vehicle lateral stability and maneuverability of six-wheeled skid-steered vehicles. The torque distribution algorithm to distribute wheel torque to each wheel of a skid-steered vehicle consists of an upper level control layer, a lower level control layer and an estimation layer. The upper level control layer is designed to obtain longitudinal net force and desired yaw moment, while the lower level control layer determines distributed driving and braking torques to six wheels. The algorithm takes vehicle speed, slip ratio and tire load information from the estimation layer, as well as actuator fault information from each in-wheel motor controller unit.

The performance of an integrated Vehicle Stability Control (VSC) system depends on not only control logic itself, but also the performance of state estimator and control threshold. In conventional VSCs, a control threshold is designed by vehicle characteristics and is centered on average drivers. A VSC algorithm with variable control threshold has been investigated in this study. The control threshold can be determined by phase plane analysis of side slip angle and angular velocity. Vehicle side slip angle estimator has been evaluated using test data. Estimated side slip angle has been used in the determination of the control threshold. The performance of the proposed VSC algorithm has been investigated by human-in-the-loop simulation using a vehicle simulator. The simulation results show that the control threshold has to be determined with respect to the driver steering characteristics.

This paper presents a methodology of trajectory planning for the surrounding-aware lane change maneuver of autonomous vehicles based on a data-driven method. The lateral motion is planned by sampling candidate patterns which are defined based on quintic polynomial functions over time. Based on the cost evaluation among the sampled candidates, the optimal lateral motion pattern is selected as a reference and tracked by the controller. The longitudinal motion is planned and controlled using Model Predictive Control (MPC) which is an optimal control method designed considering the surrounding traffic information. To realize the lane change motion similar to the human driving behavior in the surrounding traffic situation, the human driving pattern is modeled in the form of motion parameters and considered in planning the lateral and longitudinal motion.

CW/CA (Collision Warning /Collision Avoidance) Systems have been an active research and development area as interests and demands for the advanced vehicle increase. A CW/CA ‘Hardware-in-the-Loop Simulation (HiLS)’ system has been designed and used to test a CW/CA algorithm, radar sensors, and warning displays under realistic operating conditions in the laboratory. A CW/CA algorithm has two parts. One is a distance decision algorithm that determines the critical warning and braking distance and the other is a brake control algorithm for collision avoidance. The CW/CA HiLS system consists of a controller in which a DSP chip is installed, a preceding vehicle simulator, a radar sensor and a warning display. The controller calculates velocities of the preceding and following vehicles, relative distance and relative velocity of the vehicles using vehicle simulation models. The relative distance and velocity are applied to the vehicle simulator that is controlled by a DC motor.

This paper presents an Interacting Multiple Model (IMM) based side slip angle estimation method to estimate side slip angle under various road conditions for vehicle stability control. Knowledge of the side slip angle is essential enhancing vehicle handling and stability. For the estimation of the side slip angles in previous researches, prior knowledge of tire parameters and road conditions have been employed, and sometimes additional sensors have been needed. These prior knowledge and additional sensors, however, necessitates many efforts and make an application of the estimation algorithm difficult. In this paper, side slip angle has been estimated using on-board vehicle sensors such as yaw rate and lateral acceleration sensors. The proposed estimation algorithm integrates the estimates from multiple Kalman filters based on the multiple models with different parameter set.

This paper describes vehicle stability control (VSC) scheme to prevent rollover and to improve both maneuverability and lateral stability by integrating individual chassis control modules such as electronic stability control (ESC), active front steering (AFS) and continuous damping control (CDC). The proposed VSC system consists of an upper and lower level controller. The upper level controller determines a control mode such as rollover mitigation, maneuverability and lateral stability, and it also calculate desired values for its objectives. The lower level controller determines longitudinal and lateral tire forces as inputs of each control modules such as the ESC and AFS. From the simulation results, it is shown that the proposed VSC system can prevent vehicle rollover, while at the same time improving both maneuverability and lateral stability