Search Results

Laminated steel body panels are used in different applications in vehicles, such as dash panels and wheel wells. A part made out of laminated steel has the potential to provide structure-borne noise reduction and also improve the airborne noise reduction of the part compared to a monolithic part. The use of laminated steel has been more critical when there are deep draws on the part as the deep draws cause localized resonances which degrade the acoustic performance significantly. However, due to lightweighting demands, hybrid laminated panels, commonly known as acoustic patch laminates have become very attractive. This paper discusses the damping and sound transmission loss performances of a dash panel part with monolithic, laminated, and acoustic patch panels.

Standards organizations develop standards depending on the need in the market place. With the change in vehicle design, lightweighting structures, and body panels made out of aluminum and composites, SAE’s Acoustical Materials Committee is developing a new damping standard. This standard is also very suitable in determining the damping performance of materials used in the off-highway applications, where the thickness of the steel body panel is much greater than in the automotive application. The general methodology of this standard is based on the mechanical impedance measurement method and has been developed with the general consensus of automotive engineers, suppliers, and independent test laboratories. This method is essentially based on the fact that a bar is excited at the center by a shaker. The force exerted by the shaker and the corresponding vibration is measured at that point to determine the frequency response function of the mechanical impedance signal.

A study was conducted to understand the acoustic viability of using post consumer rebond seat foam materials in vehicles for floor carpet underlayment applications. These foam materials were obtained from two different sources: 1) polyurethane foam dismantled from seats of end of life vehicles (ELV or scrap vehicles), and 2) polyurethane foam recovered and cleaned from auto shredder residue (ASR) by the Argonne National Laboratories (ANL) using their cleaning method. The study was conducted using three North-American cars, each serving different market segments. Based on both laboratory and on-road tests conducted on each vehicle, the study concluded that the acoustical performance of the floor carpet underlayment part made of post consumer rebond foam is comparable to that of the current production part mostly made of shoddy materials.

The paper discusses the development of a new SAE standard J2883 for measuring sound absorption performance of absorption materials in a small reverberation room. It discusses the need for such a standard particularly in the automotive industry. It also discusses the need for understanding the parameters such as the room volume, diffusion and cut-off frequency, and the sample size that affect the measurements and how to address these parameters in developing a robust test method. Finally, the paper discusses some of the findings of the round robin tests where measurements were conducted in various size rooms, task force activities, and the proposed repeatability and reproducibility values of the test method.

The SAE International standard for testing Oberst bars has been used in the industry for many years with predictable results. Growing interest in testing wider samples to incorporate more of the variability in liquid applied sprayable dampers has led to increased use of a center point damping test method based on a Japanese standard JIS G 0602. This method is similar to that of the ISO 16940 standard for testing laminated glass. Theory shows us that an Oberst test with a free length equal to the half length of a bar used for center point testing will provide the same resonances. This paper intends to show a relationship between the resonances of bars tested with the Oberst and center point test methods. A correlation between the composite loss factor for samples tested with each of the methods will be illustrated.

In the automotive industry, random incidence sound absorption tests are conducted on flat material samples as well as on finished components such as headliners, seats, and floor carpet systems. This paper discusses a feasibility study that is being pursued by an SAE task force, under the direction of the Acoustical Materials Committee, to develop a small volume reverberation room test method for conducting random incidence sound absorption tests. This method has the potential to be suitable for flat material and component testing. A round-robin test program is being conducted to determine variability due to test procedures, room size differences and laboratory differences. The paper discusses the selection of test samples and provides an update on the findings of the round-robin test study.

This paper discusses the importance of having an industry-wide standardized laboratory test procedure for proper evaluation of vibration damping materials, and for consistency between damping tests conducted by different test facilities. Several different vibration damping test procedures that are presently used in the automotive industry are briefly discussed. However, a test method that has been selected for a new proposed SAE Recommended Practice based on exciting a beam at various modes of vibration and at different temperatures is discussed here. The relative superiority of this test method over other methods, the importance of selecting the most appropriate beam size, and how the damping performance should be measured for consistency and clarity are emphasized. A round-robin test was conducted to determine the variability of the test procedure. Factors considered were type of damping material, bar mounting, and differences between laboratory instrumentation.

Sealant materials are used in todays automobiles for many applications such as, sealing of body seams, sealing access holes and the filling of hollow cavities. The primary reasons for these applications are to prevent corrosion, prevent water intrusion, and to reduce the noise level in the passenger compartment. However, the noise control capabilities of sealant materials have not been explored until recently. This paper discusses the requirements that a noise control material must possess, and reviews how a sealant material can fulfil these requirements. Properly designed sealant materials can possess sound transmission loss (barrier) properties, vibration damping properties over a given frequency and temperature range of interest, and often sound absorption properties with proper formulation. This paper provides case studies to substantiate the acoustical capabilities of sealant materials.

Traditionally, the damping performance of a visco-elastic material is measured using the Oberst bar damping test, where a steel bar is excited using a non-contacting transducer. However, in an effort to reduce the weight of the vehicles, serious effort is put in to change the body panels from steel to aluminum and composite panels in many cases. These panels cannot be excited using a non-contacting transducer, although, in some cases, a very thin steel panel (shim) is glued to the vibrating bar to introduce ferrous properties to the bar so it can be excited. In the off highway vehicles, although the panels are made of steel, they are very thick and are difficult to excite using the Oberst bar test method. This paper discusses a measurement methodology based on mechanical impedance measurements and has the potential to be a viable/alternate test method to the Oberst bar testing. In the impedance method, the test bar is mounted to a shaker at the center (Center Point method).

The performance of damping materials is generally evaluated by experimental methods. However most damping materials used in the transportation industry cannot be excited by itself. Therefore, the measurements are generally made by exciting a damped system, where the damped system extends from a bar to a panel. The paper reviews various damped systems and excitation methodologies and discusses some of the limitations of a bar to study the damping performance for different applications. It discusses a methodology where a damped panel is mounted on a fixture and the fixture is excited with a shaker. The paper discusses data acquisition and data reduction procedures to obtain the damping performance of laminated steel acoustic patch products on a third octave band frequency basis.

The use of sealant materials to improve interior acoustics has increased significantly in todays automobiles. One such application is to use expandable sealant materials in rails, pillars, and cavities to reduce noise propagation. However, there is no standardized method for evaluating the acoustical performance of these materials. This paper reviews the basics of noise control engineering and discusses a proposed laboratory based test methodology that has been developed for properly evaluating the acoustical performance or expandable sealant materials. The test method is intended to simulate actual applications so that different materials can be evaluated to achieve optimum acoustical performance within a channel representing the rails or pillars in automobiles.

Advances in vehicle noise control are leading the automotive industry to place increasing emphasis on weatherseals to block exterior noise. As a result, properly evaluating the acoustical performance of automotive weatherseals is of increasing importance. There is no current specific standard for this testing. Rather, there has been reliance on adaptations of SAE Standard 51400 “Laboratory Measurement of the Airborne Sound Barrier Performance of Automotive Materials and Assemblies” by testing laboratories. However, the 51400 standard addresses testing of flatstock materials and does not readily lend application to pre-formed parts such as weatherseals. For this reason, adaptation of the standard can vary significantly from facility to facility and manufacturer to manufacturer. These differences can be significant and can render comparisons between test results on competing materials very difficult.

The paper discusses the importance of a well documented standardized laboratory test procedure to evaluate damping material performance for the automotive industry, and to understand the parameters that influence the precision of the test method. The standard outlines a methodology which was developed with the general consensus of automotive engineers, suppliers, and independent test laboratories. The methodology is based on the Oberst bar test method where a damping material is bonded to a specific size steel bar and the system is excited at its various modes of vibration under a cantilevered configuration. The damping performance is expressed in terms of composite loss factor, ηc, within the frequency range of approximately 100 Hz to 1000 Hz, and over the useful range of temperatures for the given application.

Automotive noise control involves many aspects of the total vehicle design - the powertrain, body structure, chassis and so forth. Noise control materials in conjunction with intelligent vehicle design can help produce a pleasant, desirable vehicle. Understanding the basic functions and uses of noise control materials is one of the objectives of this paper. In some situation, thermal insulation materials are combined with or used in conjunction with noise control materials, and an understanding of the thermal properties of materials can be useful. Vibration isolators are important devices in controlling the transfer of sound and vibration energy and these are discussed.

Heat reactive expanding sealer materials are used as acoustical “baffles” to block noise propagation in rails, pillars, posts, and rockers. However, should moisture enter and collect in vertical pillars water damage may occur. Therefore, effort is being made to implement a drainage system for these problem applications. This paper discusses an effective way to prevent water damage by adding an acoustical drain plug to the baffle system with a minimal reduction in acoustical performance. The paper also discusses the performance and the effect of adding this plug to the baffle system. Finally, results of design variations of the plug on the baffle system are reported.

Body cavity fillers are used to inhibit noise propagation/amplification through body cavities such as sills, pillars, and posts' to improve vehicle NVH performance. Cavity fillers should be optimized by matching their performance with the global NVH objectives of the vehicle. A standard test method must be defined to acquire acoustical profiles and facilitate in the proper selection of materials based on performance. This paper discusses test results of 38 cavity filler samples which represent all currently used materials by the “Big Three” automotive OEMs. The samples were grouped into 4 categories based on their weight and fill configurations. Data was obtained utilizing an established, laboratory based, acoustical test method for fillers (SAE paper 930336). The laboratory results were analyzed to generalize the performance of cavity filler materials and to set acoustical goals for vehicle applications.

This paper discusses a development procedure that was used to evaluate the acoustical performance of one type of dashpanel construction over another type for a given application. Two very different constructions of dashpanels, one made out of plain steel and one made out of laminated steel, were studied under a series of different test conditions to understand which one performs better, and then to evaluate how to improve the overall performance of the inferior dashpanel for a given application. The poorly performing dashpanel was extensively tested with dashmat and different passthroughs to understand the acoustic strength of different passthroughs, to understand how passthroughs affect the overall performance of the dash system, and subsequently to understand how the performance can be improved by improving one of the passthroughs.

Small reverberation rooms are used in common practice for determining random incidence sound absorption properties of flat materials and finished parts. Based on current small reverberation room usage in the automotive industry, there is a need for standardization that would bring about an appropriate level of consistency and repeatability. To respond to this need, a feasibility study is being pursued by an SAE task force, under the direction of the Acoustical Materials Committee, to develop a small volume reverberation room test method for conducting random incidence sound absorption tests. In addition to an accepted test method for small reverberation rooms, a data driven correlation that relates full size reverberation room absorption testing to small size reverberation room testing would be beneficial in understanding the usage of both. A Round Robin study has been underway for more than three years and will be completed in 2005.

This paper discusses the development of a small sample test facility for properly evaluating the low frequency noise control performances of various automotive acoustical materials. Based on several tests conducted with 0.61 m (24 in) diameter samples, this facility is designed to operate in the frequency range of 35 Hz to 355 Hz. Near-field root-mean-square acoustic pressure and acoustic velocity were measured for this purpose, using a dual microphone probe. This methodology allows one to test acoustical materials without elaborate test facilities and without the need for any special acoustic test environment.

Constrained layer damping (CLD) is a well known technique to efficiently damp low frequency vibration. CLD employs a viscoelastic material sandwiched between two very stiff, typically metal, layers. While effective over essentially flat surfaces, CLD has not been applicable to cylindrical shapes. In order to damp low frequency vibration in metal pipes, users have been forced to rely on extensional layer damping, typically consisting of thick layers of extruded or molded rubbers. This paper discusses a novel product to damp cylindrical articles such as metal pipes with a constrained layer heat shrink tubing. This product utilizes a stiff heat shrinkable polymeric jacket bonded on the inside with a viscoelastic layer. When shrunk on a metal pipe or rod, a CLD system is produced. The product is typically thinner than an extensional layer damper and is more effective. It also meets the other physical and environmental requirements for a pipe covering.