Search Results

Standard

Small Craft - Marine Propulsion Engine and Systems - Power Measurements and Declarations

2016-04-06

CURRENT

J1228_201604

This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull. It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.

Standard

SMALL CRAFT—MARINE PROPULSION ENGINE AND SYSTEMS—POWER MEASUREMENTS AND DECLARATIONS

1991-11-01

HISTORICAL

J1228_199111

This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull. It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.

Standard

Small Craft - Marine Propulsion Engine and Systems - Power Measurements and Declarations

2021-02-19

WIP

J1228

This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull.

It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.

Standard

MARINE PROPELLER-SHAFT COUPLINGS

1987-08-01

HISTORICAL

J756_198708

This SAE Standard covers propeller shaft couplings for use with propeller shafts up to 3 inches outside diameter.

Standard

MARINE PROPELLER-SHAFT COUPLINGS

1981-08-01

HISTORICAL

J756_198108

This SAE Standard covers propeller shaft couplings for use with propeller shafts up to 3 inches outside diameter.

Standard

Electric Hourmeter Specification

1998-07-01

HISTORICAL

J1378_199807

This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.

Standard

Electric Hourmeter Specification

2011-03-08

CURRENT

J1378_201103

This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.

Standard

Thrust Test Device

2017-03-22

HISTORICAL

J1286_201703

This method covers electric outboards that are rated in terms of static thrust.

Standard

Thrust Test Device

2009-05-04

HISTORICAL

J1286_200905

This method covers all electric outboards.

Standard

Small Craft - Graphic Symbols

2015-05-12

CURRENT

J1449_201505

This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.

Standard

Small Craft—Graphic Symbols

2009-08-25

HISTORICAL

J1449_200908

This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.

Standard

Small Craft—Graphic Symbols

2002-03-15

HISTORICAL

J1449_200203

This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.

Standard

GRAPHIC SYMBOLS FOR BOATS

1987-02-01

HISTORICAL

J1449_198702

This SAE Recommended Practice defines graphic symbols for functions, indicators, controls, systems and equipment on board boats.

Standard

Operator Sound Pressure Level Exposure Measurement Procedure for Powered Recreational Craft

2022-04-25

CURRENT

J1281_202204

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.

Standard

Operator Sound Pressure Level Exposure Measurement Procedure for Powered Recreational Craft

2016-11-15

HISTORICAL

J1281_201611

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.

Standard

Operator Sound Pressure Level Exposure Measurement Procedure for Powered Recreational Craft

2009-08-21

HISTORICAL

J1281_200908

This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.

Standard

RECIPROCATING INTERNAL COMBUSTION ENGINES—PERFORMANCE—PART 1: STANDARD REFERENCE CONDITIONS, DECLARATIONS OF POWER, FUEL AND LUBRICATING OIL CONSUMPTIONS, AND TEST METHODS

1994-11-01

HISTORICAL

J3046/1_199411

This part of ISO 3046 specifies standard reference conditions and methods of declaring the power, fuel consumption, lubricating oil consumption, and test methods for reciprocating internal combustion (RIC) engines in commercial production using liquid or gaseous fuels. Where necessary, individual requirements are given for particular engine applications. This part of ISO 3046 covers RIC engines for land, rail-traction, and marine use, excluding engines used to propel agricultural tractors, road vehicles, and aircraft. This part of ISO 3046 may be applied to engines used to propel road construction and earthmoving machines, industrial trucks, and for other applications where no suitable International Standard for these engines exists. This part of ISO 3046 may be applied to tests on a test bed at the manufacturer's works and to tests on site (see 15.4.4).

Standard

Reciprocating Internal Combustion Engines--Performance--Part 1: Standard Reference Conditions, Declarations of Power, Fuel and Lubricating Oil Consumptions, and Test Methods

2005-04-25

CURRENT

J3046/1_200504

This part of ISO 3046 specifies standard reference conditions and methods of declaring the power, fuel consumption, lubricating oil consumption, and test methods for reciprocating internal combustion (RIC) engines in commercial production using liquid or gaseous fuels. Where necessary, individual requirements are given for particular engine applications. This part of ISO 3046 covers RIC engines for land, rail-traction, and marine use, excluding engines used to propel agricultural tractors, road vehicles, and aircraft. This part of ISO 3046 may be applied to engines used to propel road construction and earthmoving machines, industrial trucks, and for other applications where no suitable International Standard for these engines exists. This part of ISO 3046 may be applied to tests on a test bed at the manufacturer's works and to tests on site.

Standard

Thrust Test Device

2023-02-20

CURRENT

J1286_202302

This method covers electric outboards that are rated in terms of static thrust.

Standard

Marine Circuit Breakers

2013-05-16

CURRENT

J1428_201305

This recommended practice covers the requirements of magnetic or thermal circuit breakers for use in marine applications for 50 V DC or less.