Refine Your Search

Date

Date

Topic

Topic

Author

Author

Plastics Fibers

Search Results

Viewing 1 to 20 of 238
123Next >Last >>
Sort by relevance
Standard

Materials for Plastic Check Valves for Vacuum Booster Systems
2001-05-14
CURRENT
J1875_200105
The materials defined by this SAE Standard are unreinforced thermoplastic acetal and thermoplastic 6/6 heat stabilized nylon, as both materials will function in this application. The specific material chosen will depend on the final application's surroundings and heat requirements. They are for use in vacuum booster check valves for hydraulic brake systems.
Standard

ROAD VEHICLES—HIGH PRESSURE FUEL INJECTION PIPE END—CONNECTIONS WITH 60 DEGREE FEMALE CONE
1988-10-01
HISTORICAL
J1949_198810
This SAE Standard specifies the dimensional requirements for the assembly of high-pressure pipe connections for compression-ignition (diesel) engine fuel injection equipment. It applies to 60 degrees female cones with external threaded connectors types 1 and 2 (see Figures 1, 2, and 3), and to the internal threaded tube nuts and male cone type end assembly (see Figure 4) of high-pressure pipe connections for tubes with diameters up to 12 mm inclusive.
Standard

Standard Specification for Allowable Defects in Rolled Goods for Interior Trim
2022-01-28
CURRENT
J3064_202201
This specification is written for rolled goods used for trim sets for automotive seats. Face materials are fabric-woven or knitted textiles, and plastic goods like polyvinyl chloride (PVC), thermoplastic polyolefin (TPO), or thermoplastic polyurethane (TPU). This specification covers material rolled goods with and without foam or backing adhered to the face material.
Standard

Thread Sealants
2001-08-06
HISTORICAL
J1615_200108
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Standard

Thread Sealants
2016-08-16
HISTORICAL
J1615_201608
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Standard

Thread Sealants
2021-01-27
CURRENT
J1615_202101
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Standard

TEST PROCEDURES FOR AUTOMOTIVE STRUCTURAL COMPOSITE MATERIALS
1995-12-01
HISTORICAL
J2253_199512
This SAE Standard is intended to serve as a guide for the collection of physical, mechanical, and thermal properties of fiber-reinforced polymer composite materials for automotive structural applications. This document attempts to utilize test methods applicable to the widest range of structural materials and processes without compromising the integrity of the data being sought. A summary of the material characterization is shown in Section 15.
Standard

Test Procedures for Automotive Structural Composite Materials
2017-07-12
CURRENT
J2253_201707
This SAE Standard is intended to serve as a guide for the collection of physical, mechanical, and thermal properties of fiber-reinforced polymer composite materials for automotive structural applications. This document attempts to utilize test methods applicable to the widest range of structural materials and processes without compromising the integrity of the data being sought. A summary of the material characterization is shown in Section 15.
Standard

Dual Dimensioning Engineering Drawings
1999-05-01
CURRENT
J390_199905
This document covers a dual dimensioning practice that provides both U.S. customary inch-pound units and SI metric units for all dimensions on the field of the drawing. The scope does not include the various methods by which computer programs are used for dual dimensioning. In one method that has had some usage, drawings are dimensioned in SI (metric) units, with conversions to U.S. customary inch-pound units provided in a computer-generated chart on the drawing.
Standard

Use of Terms Yield Strength and Yield Point
2017-10-10
CURRENT
J450_201710
The purpose of this SAE Recommended Practice is to describe the terms yield strength and yield point. Included are definitions for both terms and recommendations for their use and application.
123Next >Last >>
X