Refine Your Search

Date

Date

Topic

Topic

Author

Author

Failure modes and effects analysis (FMEA) Fibers

Search Results

Viewing 1 to 20 of 399
123Next >Last >>
Sort by relevance
Standard

Field Test Analysis Information Report
1999-12-14
CURRENT
J2372_199912
This SAE Information Report describes results of testing of the SAE J1746 ISP-Vehicle Standard for the communication of spatial data references between central sites and mobile vehicles on roads. Testing was performed by the Oak Ridge National Laboratory and its contractors, resulting in a document from which this Information Report has been extracted. Tests were performed by computer analysis and corroborated by field tests with a mobile vehicle.
Standard

GLOSSARY OF RELIABILITY TERMINOLOGY ASSOCIATED WITH AUTOMOTIVE ELECTRONICS
1988-10-30
CURRENT
J1213/2_198810
This compilation of terms, acronyms and symbols was drawn from usage which should be familiar to those working in automotive electronics reliability. Terms are included which are used to describe how items, materials and systems are evaluated for reliability, how they fail, how failures are modeled and how failures are prevented. Terms are also included from the disciplines of designing for reliability, testing and failure analysis as well as the general disciplines of Quality and Reliability Engineering. This glossary is intended to augment SAE J1213, Glossary of Automotive Electronic Terms.
Standard

Model Specification Process Standard
2002-02-15
CURRENT
J2546_200202
The modeling requirements listed in this document provide guidelines for specifying: Analysis requirements Computer-Aided Engineering (CAE) simulator Model fidelity System assumptions Model architecture Validation requirements Deliverables for electrical/electronic components and the integral interfacing systems (mechanical, thermal, hydraulic) associated with these components. The simulation models are primarily intended to facilitate functional specification and operational evaluation between component and system manufacturers, and are not intended to otherwise constrain or restrict the use of CAE simulation tools for automotive design, analysis and validation.
Standard

SHIP SYSTEMS AND EQUIPMENT—FASTENERS—SELECTION AND IDENTIFICATION REQUIREMENTS
1996-04-01
HISTORICAL
J2280_199604
This SAE Standard provides a comprehensive list of requirements for the selection, identification, and control of metric and inch sized fasteners for use in shipboard applications for both shipbuilder installed joints and for use in shipboard components. The fastener selection requirements include the following: a Materials b Thread selection c Plating, coatings, and surface treatments d Locking devices and elements e Screw thread fastener inserts f Fastener part or identifying numbers g Identification markings
Standard

Recommended Test Procedure for Powered Gas Brake Control Systems
2007-10-22
HISTORICAL
J2604_200710
This test procedure is for qualification testing of powered gas/brake control systems to assure compliance with the Recommended Practices for these assistive devices. A powered gas/brake control system which passes all of the tests shall be considered to be in compliance with the Recommended Practices. The control shall pass all tests denoted by a “shall” in the Recommended Practice or the Recommended Test Procedure. All the results of all tests and requirements denoted by a “should” shall be noted, but failure to comply will not constitute failure to pass the test.
Standard

Recommended Test Procedure for Powered Gas Brake Control Systems
2021-11-03
CURRENT
J2604_202111
This test procedure is for qualification testing of powered gas/brake control systems to assure compliance with the recommended practices for these assistive devices. A powered gas/brake control system which passes all of the tests shall be considered to be in compliance with the recommended practices. The control shall pass all tests denoted by a “shall” in the recommended practice or the recommended test procedure (RTP). All the results of all tests and requirements denoted by a “should” shall be noted, but failure to comply will not constitute failure to pass the test.
Standard

ROAD VEHICLES—HIGH PRESSURE FUEL INJECTION PIPE END—CONNECTIONS WITH 60 DEGREE FEMALE CONE
1988-10-01
HISTORICAL
J1949_198810
This SAE Standard specifies the dimensional requirements for the assembly of high-pressure pipe connections for compression-ignition (diesel) engine fuel injection equipment. It applies to 60 degrees female cones with external threaded connectors types 1 and 2 (see Figures 1, 2, and 3), and to the internal threaded tube nuts and male cone type end assembly (see Figure 4) of high-pressure pipe connections for tubes with diameters up to 12 mm inclusive.
Standard

Thread Sealants
2001-08-06
HISTORICAL
J1615_200108
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Standard

Thread Sealants
2016-08-16
HISTORICAL
J1615_201608
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Standard

Thread Sealants
2021-01-27
CURRENT
J1615_202101
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Standard

Testing of Wheelchair Lifts for Entry to or Exit from a Personally Licensed Vehicle
2021-04-14
CURRENT
J2092_202104
This test procedure is for Qualification Testing of electrically powered hydraulic or mechanically operated devices which permit a person in a manual or powered wheelchair to enter or exit a personally licensed vehicle. It establishes minimum test requirements for compliance. A lift completing the test without failure under this procedure shall be considered in compliance. The tests in Section 3 shall be done in the sequence listed.
Standard

Design Considerations for Wheelchair Lifts for Entry to or Exit from a Personally Licensed Vehicle
2021-04-14
CURRENT
J2093_202104
This SAE Recommended Practice applies to electrically powered hydraulic or mechanically operated platform devices which permit a person seated in a manual or powered wheelchair to enter or exit a personally licensed vehicle. The minimum performance and durability requirements are specified for satisfactory installation of wheelchair lifting devices in a personally licensed vehicle to be used by a person seated in a wheelchair to be lifted from the ground plane to the vehicle floor level in a reliable and safe manner.
123Next >Last >>
X