Search Results

In this paper results on in-cylinder pollutant concentration evolution during combustion of six different oxygenated fuels, in comparison with tetradecane and n-octane combustion, are presented. These four fuels are: Ethylene-Glygol-Dimethylether (monoglyme-C4H10O2), Diethylene-Glygol-Dimethylether (diglyme-C6H14O2), Diethylene-Glycol-Diethylether (diethyldiglycol-C8H18O3), butylether (C8H18O). Two techniques were adopted on a single cylinder direct injection diesel engine: two-color pyrometry for the measurement of in-cylinder soot loading and a fast sampling valve for the measurements of in-cylinder combustion products. In addition, the sampling line downstream of the fast sampling valve was adapted for the in-cylinder aldehyde measurements. The main results obtained provide information about the mechanisms that control soot evolution during diesel combustion.

The effect of different fuel parameters on emissions is difficult to understand, the response depending upon different engine technologies. In addition the isolation of some of the fuel variables is often very hard. The present paper discusses the main results obtained testing a matrix of 14 fuels designed for obtain large variations of cetane number, sulphur and aromatic contents of Diesel oil. The aromatic structure of fuels and its effect on particulate emissions was also investigated. A linear regression analysis was performed in order to isolate the main controlling factors on particulate emissions. Finally the influence of aromatic contents of fuel on unregulated emissions was also assessed.

Three dimensional computations of Diesel combustion were performed using a modified version of Kiva II code. The autoignition and combustion model were tuned on a set of experimental conditions, changing the engine design, the operating conditions and the fuel characteristics. The sensitivity of the model to the different test cases is acceptable and the experimental trends are well reproduced. In addition the peak of pressure and temperature computed by the code are quite close to the experimental values, as well as the pressure derivatives. Once tuned the combustion model constants, different but simple formulations for the soot formation and oxidation processes were implemented in the code and compared with the experimental measurements obtained both with fast sampling technique and two colors method. These formulations were found unable to give good prediction in a large range of engine operating conditions, even if the model tuning may be very good for each test point.

Cetane number, sulphur content and aromatic structure of Automotive Diesel Oil (ADO) were changed to assess their influence on emissions of light duty direct injection Diesel engine. The detailed chemical analysis of particulate soluble fraction allows to quantify the P.A.Hs emission. In addition also the aldehydes and volatile organic compounds were measured in the gaseous phase. The sulphur content of the fuel and its aromatic structure strongly influence particulate emission. The insoluble fraction of the particulate rises with an increase of the high sulphur content ADOs with about the same back end volatility. Unburned P.A.Hs control P.A.Hs emission at the part loads typical of normalized schedules for emission testing of light duty vehicles in Europe. Finally the level of emissions of benzene and 1-3 butadiene is comparable to the total P.A.Hs emission.

A modified version of KIVA II code was used to perform three-dimensional calculations of combustion in a DI diesel engine. Both an ignition delay submodel and a different formulation of the fuel reaction rate were implemented and tested. The experiments were carried out on a single cylinder D.I. diesel of 0.75 I displacement equipped with sensors to detect injection characteristics and indicated pressure. A fast acting sampling valve was also installed in the combustion chamber to allow the measurement of main pollutants during the combustion cycle, by an ensemble average technique. Computational and experimental results are compared and the discrepancies are discussed. Today the demand for light duty engines that produce less emission and consume less fuel is increasing. Thus, if limits on CO2 emissions are established, the direct injection diesel engine for light duty applications will become an attractive option.

A 1.2 l instrumented car, equipped with an on-board acquisition system capable of detecting and recording car speed, gear, engine and catalyst operating parameters, has been tested in designed trips all over Naples urban area with different drivers. Driving cycles statistically representative of car operation under different traffic conditions in urban and expressway trips, have been determined by multivariate statistical analysis of speed and gear. Emission tests have been performed in the laboratory with car on the dynamometer chassis using defined driving cycles and engine/catalyst conditions to define emission factors for this type of car for a wide and significant spectrum of road performance.

This paper reports on the first successful tests performed on a production D.I. Diesel engine using wood pyrolysis oil (WPO). As reported in literature, any attempt to directly replace Diesel fuel with WPO required extensive modifications to the engine injection system, in order to overcome the intrinsic limits of the oil (poor self-ignition, high acidity and viscosity): new materials, additional pilot injection systems, careful procedures of start-up and shutdown were needed to obtain acceptable operation. Aim of the present work was to assess the limits of utilization of WPO in a strictly stock engine. Therefore, while no modifications at all were carried out on the engine, the efforts were addressed to make the WPO compatible with light-duty Diesel engines. Several long-running tests were performed on a single-cylinder engine, with: blends of WPO with different percentage of oxygenated compounds micro-emulsions of WPO in Diesel fuel standard (commercial) Diesel fuel.

This paper presents the performances of a modern DI diesel engine, equipped with a Common Rail injection system, fed on blends of an advanced diesel fuel (base fuel) and Diethylene-Glycol-Dimethyl-Ether (Diglyme - C6H14O3). The base fuel was a reformulated diesel fuel with low aromatic and sulfur content. Three blends with different volumetric percentage of Diglyme (10, 20 and 30%) in the base fuel were prepared and tested. The engine was a FIAT M724, installed in a Alfa Romeo 156 1.9 JTD, with a Bosch Common Rail injection system (EDC-15C). At the exhaust of the engine, soot, NOx, HC, CO, and CO2 were measured. The experiments represent the potential of diesel reformulation technology with synthetic fuels coupled with the new diesel technology generation.