Search Results

Presented here are analyses and statistical summaries of data collected from 11,299 flight operations recorded on 6 BE-1900D aircraft during routine commuter service over a period of three years. Basic flight parameters such as airspeed, altitude, flight duration, etc. are shown in a form that allows easy comparison with the manufacturer's design criteria. Lateral ground loads are presented for ground operations. Primary emphasis is placed on aircraft usage and flight loads. Maneuver and gust loads are presented for different flight phases and for different altitude bands. In addition, derived gust velocities and various coincident flight events are shown and compared with published operational limits.

An experimental study was performed to investigate large droplet dynamics in the vicinity of an airfoil. The investigation was conducted using the NASA Glenn Droplet Imaging Flow Tunnel (DrIFT). Mono-dispersed large droplets were released at the tunnel inlet and accelerated toward an airfoil that was mounted in the test section. The dynamic behavior of a droplet's encounter with the airfoil, which may involve droplet distortion, break-up, impingement and splashing, was recorded using a high-speed imaging system. The effects of the droplet size, tunnel velocity and airfoil configuration on the droplet dynamics were investigated in a parametric study. The droplet sizes used in the experimental study were 96 and 375 μm whereas tunnel velocities were varied from 80 to 130 mph. Three different airfoil geometries were used in the experimental study; a ‘clean’ and ‘iced’ airfoil, and a ‘clean’ three-element high-lift airfoil. The incidence angle of these airfoils was set to zero degrees.

Ice particles shed from aircraft surfaces are a safety concern because they can damage aft-mounted engines and other aircraft components. Ice shedding is a random and complex phenomenon. The randomness of the ice fragment geometry, size, orientation and shed location in addition to potential particle breakup during flight poses considerable simulation challenges. Current ice shedding analysis tools have limited capabilities due to the lack of experimental aerodynamic coefficients for the forces and moments acting on the ice fragment. A methodology for simulating the shedding of large ice particles from aircraft surfaces was developed at Wichita State University. This methodology combines experimental aerodynamic characteristics of ice fragments, computational fluid dynamics, trajectory analysis and the Monte Carlo method to provide probability maps of shed particle footprints at desired locations.

An algorithm is developed and validated for automatic avoidance of restricted airspaces. This method is devised specifically for implementation with an advanced flight control system designed for general aviation application. The algorithm presented here implements two inputs to the aircraft; the bank angle, and the airspeed, while the control system always ensures coordinated maneuvers. Unlike collision avoidance systems, the current method is not designed to serve in an advisory role, but to assume complete control of the aircraft if necessary. It is demonstrated that in order to implement this technique, the aircraft must be assigned an immediate domain whose size would have to depend on the aircraft performance and flight conditions. The strategy is designed such that as the domain surrounding the aircraft approaches that of the restricted airspace, aircraft control would switch gradually away from the pilot and to the controller, which would initiate an evasive maneuver.

Data obtained from digital flight data recorders are used to assess the actual operational environment of propellers on a fleet of Beech 1900D aircraft in commuter role. Information is given on various aerodynamic parameters as well as those pertaining to engine and propeller usage. The takeoff rotation has been identified as the most demanding phase of flight in terms of unsteady loads exerted on the propeller blades. Special attention is paid to ground operations.

The current emphasis on environment protection by reducing noise pollution has led to stricter noise standards for general aviation aircraft. As a result, there is a growing demand for a computational tool to predict the noise during the design process. A computer program, called ProRAPP, has been developed for the prediction of noise generated by propeller/rotor blades. The acoustic pressure is calculated using a form of Ffowcs Williams-Hawkings equation which is suitable for numerical implementation. For noise predictions, the observer can either move with the propeller/rotor hub or it can be fixed to the ground. Experimental data from both wind tunnel and flight tests are used to validate the numerical results.

Global warming concerns are stimulating accelerated research and development of alternative fuels and propulsion systems for automobiles. The potential application of these emerging technologies to airplanes is reviewed. Preliminary designs of zero greenhouse gas emission airplanes using hydrogen fuel and either internal combustion or fuel cell-electric motor propulsion are presented for a wide body jet transport, medium jet transport, business jet, and single engine propeller airplane. The hydrogen fueled internal combustion engine airplanes offer the easiest path to zero emissions, but the greater efficiency of the fuel cell airplanes allows designs requiring substantially less fuel. The single engine propeller airplane is the easiest to modify for hydrogen fuel, because of the relatively high mass and volume of the engine being replaced. Technology improvements needed to make zero emission airplanes viable are suggested.

A unique cascade test facility has been developed for use in the Wichita State University (WSU) water table. Although small in scale, the WSU water table has the advantage of low cost and the ease with which test conditions can be varied. Water table facilities have been used in the past for cascade experiments, especially as analogies for compressible flow visualization of turbine cascades. However, the lack of a quantitative measurement technique at low speeds has precluded the use of the water table as an analogy for testing subsonic compressors and turbines. In the present experiment, the hydrogen bubble flow visualization technique is used to generate bubble time lines, and a CCD (Charge Coupled Device) video camera system captures and digitizes these time line images. A VisualBASIC® computer program is then used to determine the wake velocity profile based on the difference in bubble line positions at successive intervals of time.

The competitive market has forced the industry to develop methodologies to reduce lead-time of the products without sacrificing quality. One of the major metal removal operations in the aerospace industries is drilling. Over 100,000 holes are made for a small single engine aircraft. Naturally, demand for faster production rate results in the demand for high-speed drilling. But the cost of hole-making operations becomes a significant portion of the total manufacturing cost. This paper discusses the high speed drilling of Al-2024-T3 alloy, the effect of feed and speed on hole quality features like oversize, roundness error, burr height and surface roughness.

Experimental studies were conducted to investigate the effect of tailplane icing on the aerodynamic characteristics of 15%-scale business jet aircraft. The simulated ice shapes selected for the experimental investigation included 9-min and 22.5-min smooth and rough LEWICE ice shapes and spoiler ice shapes. The height of the spoilers was sized to match the horns of the LEWICE shapes on the suction side of the horizontal tail. Tests were also conducted to investigate aerodynamic performance degradation due to ice roughness which was simulated with sandpaper. Six component force and moment measurements, elevator hinge moments, surface pressures, and boundary layer velocity profiles were obtained for a range of test conditions. Test conditions included AOA sweeps for Reynolds number in the range of 0.7 based on tail mean aerodynamic chord and elevator deflections in the range of -15 to +15 degrees.

While most industries have already adopted the use of IP networks to exploit the many advantages of network connectivity, the aircraft industry still has not significantly deployed networked devices in the aircraft. Security and reliability are two main concerns that have slowed the transition to this technology. The ability for Air Traffic Control to send digital communications to aircraft could significantly improve the aircraft safety by improving the speed and efficiency of communications. In addition, if devices could offload flight data to servers on the ground for analysis, the accuracy and efficiency of maintenance and other decisions impacting the aircraft could significantly improve. The purpose of this research is to propose an IP-based LAN architecture for the aircraft which provides a scalable solution without jeopardizing flight safety.

A supplier satisfaction survey was developed and administered to 129 Aircraft suppliers who are AS9100 registered. The primary objective of the survey was to assess organizational benefits, attributed to the AS9100 standard, and registration process difficulties. Survey results from 49 responses indicated that the primary reason for seeking AS9100 registration was customer requirement, followed by improving production and service. Further analysis indicated that the top three difficulties were evaluating effectiveness of employee training, obtaining and analyzing data on customer feedback and satisfaction, and monitoring and measuring processes. The top three reported benefits, improved quality awareness among employees, an increase in employee training, and improved internal communication, respectively, were all non-financial in nature.

This study presents the prediction of the dimensional variation of holes due to sheet metal bending using the hydroforming technique. Sheet metal with pre-drilled holes was evaluated for a bending operation using a hydroforming technique. Sheet metal with a variety of thicknesses, bending radii, and bending angles was evaluated. Variation in the dimensional tolerance due to the bending was attained using the minimum radial separation method. A dataset of dimensional variation in the holes was developed and used for development of the artificial neural network, which was able to predict the dimensional variation of the hole if an unknown pattern of inputs was provided.

The reliability and maintenance of electrical wiring and electrical components in aging aircraft have become areas of concern for the aviation industry. Numerous investigations have been conducted on the aging aspects of wiring and systems of large transport and military airplanes, with funding primarily from the FAA (Federal Aviation Administration), Air Force, and NASA. However, because of the large number of smaller general aviation aircraft in service, a need for examining the condition of wiring, electrical components and maintenance procedures for smaller aircraft exists. The Aging Aircraft Research Laboratory at the National Institute for Aviation Research (NIAR), Wichita State University, has conducted a comprehensive teardown evaluation of three high time commuter class airplanes. This teardown included assessment of aircraft wiring, electrical systems and circuit breakers through general and intrusive visual inspections and laboratory tests.

An envelope protection scheme is proposed for responding to a microburst. This approach is based on limiting the allowable maximum inertial deceleration of the aircraft when flying at low airspeeds. This technique is shown in simulations to be very effective at preventing stall and resulting in minimal loss of altitude. It is speculated that the same scheme can also protect an aircraft in the event of other forms of windshear encounters, such as making a sudden turn to downwind.

The results of an analytical study of aerodynamic interference effects for a light twin aircraft are presented. The data presented concentrates on the influence of a wing on a body (the fuselage). Wind tunnel comparisons of three fillets are included, with corresponding computational analysis. Results indicate that potential flow analysis is useful to guide the design of intersection fairings, but experimental tuning is still required. While the study specifically addresses a light twin aircraft, the methods are applicable to a wide variety of aircraft.

This paper presents a method by which artificial neural networks can be trained and used to identify a possible spin entry, differentiate between an incipient spin and a stabilized spin, and predict required recovery controls. These were then implemented into a simulation and tested using data from actual flight tests conducted by NASA Langley Research Center, to verify that artificial neural networks can successfully be used for this application. The spin avoidance and recovery system functioned properly. In addition, a weighting system was developed to predict possible spin characteristics of aircraft, depending on the relative magnitude of the three principal moments of inertia.

Multiple site damage (MSD) on aging aircraft accumulates from fatigue loading over a period of time. For ductile materials such as 2024-T3 aluminum, MSD may lower the strength below that which is predicted by conventional fracture mechanics. An analytical model referred to as the linkup (or plastic zone touch) model has previously been used to describe this phenomenon. However, the linkup model has been shown to produce inaccurate results for many configurations. This paper describes several modifications of the linkup model developed from empirical analyses. These modified linkup models have been shown to produce accurate results over a wide range of configurations for both unstiffened and stiffened flat 2024-T3 panels with MSD at open holes. These modified models are easy to use and give quick and accurate results over a large range of parameters.

An experimental study was conducted to investigate ice-adhesion on clean and coated aluminum surfaces. A test apparatus using the parallel plate linear shear technique was designed along with a data acquisition system for conducting the tests and recording the experimental data. A low pulling rate was applied to specially prepared test specimens for measuring the strength of ice adhesion for a range of test conditions. The effects of surface roughness, surface contamination, and water impurity on ice adhesion were investigated. In addition, tests were conducted to evaluate the effectiveness of a low ice-adhesion coating applied to aluminum test specimens. The results obtained showed that the bond between ice and metal was considerably lower for tap water than for distilled water. For the clean and coated aluminum surfaces the strength of ice adhesion varied with specimen roughness. However, no clear trend was established between ice adhesion strength and surface roughness.

Drilling is one of the most widely applied manufacturing operations. Millions of holes are drilled today in manufacturing industries especially in aerospace industry where high quality holes are essential. Rejection and rework rate of the products because of the bad hole is quite high. In this research graphite/honeycomb composite material and aluminum sheet metal has been used. The results show that drill geometry, speed and feed rate have substantial effects on the hole quality and also there was gradual variation of the thrust and lateral forces with feed rates.