Search Results

This paper presents an overview of the progression of the contemplated candidate volumes for the Lunar Lander since the beginning of the Vision for Space Exploration in 2004. These sets of data encompass the 2005 Exploration Systems Architecture Study (ESAS), the 2006 Request for Information on the Constellation Lunar Lander, the 2007 Lander Design Analysis Cycle −1 (LDAC-1) and the 2008 Lunar Lander Development Study (LLDS). This data derives from Northrop Grumman Corporation analyses and design research. A key focus of this investigation is how well the lunar lander supports crew productivity.

Exposure to microgravity during space flight causes bone loss when calcium and other metabolic by-products are excreted in urine voids. Frequent and accurate measurement of urine void volume and constituents is thus essential in determining crew bone loss and the effectiveness of the countermeasures that are taken to minimize this loss. Earlier space shuttle Urine Monitoring System (UMS) technology was unable to accurately measure urine void volumes due to the cross-contamination that took place between users, as well as to fluid system instabilities. Crew urine voids are currently collected manually in a flexible plastic bag that contains a known tracer quantity. A crew member must completely mix the contents of this bag before withdrawing a representative syringe sample for later ground analysis. The existing bag system accuracy is therefore highly dependent on mixing technique.

A long-duration lunar outpost will rely entirely upon imported or preserved foods to sustain the crew during early Lunar missions. Fresh, perishable foods (e.g. salad crops) would be consumed by the crew soon after delivery by the re-supply missions, and can provide a supplement to the diet rich in antioxidants (bioprotectants) that would serve as a countermeasure to radiation exposure. Although controlled environment research has been carried out on the growth of salad crops under a range of environmental conditions, there has been no demonstration of sustainable production in a flight-like system under conditions that might be encountered in space. Several fundamental challenges that must be overcome in order to achieve sustained salad crop production under the power, volume and mass constraints of early Lunar outposts include; growing multiple species, sustaining productivity through multiple plantings, and minimizing time for crew operations.

Scope of the DRESS project is to research, develop and validate a distributed and redundant electrical steering system technology for an aircraft nose landing gear. The new system aims to: • reduce system weight at aircraft level, replacing the current hydraulic actuation system with an electric one. • improve aircraft safety, achieving higher system redundancy levels compared to the current technology capabilities. This paper presents an outline of different activities occurring in the DRESS project and also shows preliminary results of the new system performance.

Due to the conventional autoclaving of pre-impregnated materials causes high costs in the production of carbon fibre structures, new injection methods have become more and more relevant. The research project “CFK-Tex” focuses on the automated handling and processing of preforms out of dry carbon fibre textiles. Regarding the advantages in quality improvement and process time, an automation of all process steps is getting enforced. The major challenge, in addition to the difficult handling-properties of the materials and high quality demands, is the enormous variety of outline variants caused by small production quantities but many different textile cuts per part. In the first step the requirements of an automated system are exactly analyzed considering the specific material properties as well as process and product based characteristics.

In support of the Constellation Program, NASA conducted an analysis of crew clothing and laundry options. Disposable clothing is currently used in human space missions. However, the new mission duration, goals, launch penalties and habitat environments may lead to a different conclusion. Mass and volume for disposable clothing are major penalties in long-duration human missions. Equivalent System Mass (ESM) of crew clothing and hygiene towels was estimated at about 11% of total life support system ESM for a 4-crew, 10-year Lunar Outpost mission. Ways to lessen this penalty include: reduce clothing supply mass through using clothes made of advanced fabrics, reduce daily usage rate by extending wear duration and employing a laundry with reusable clothing. Lunar habitat atmosphere pressure and therefore oxygen volume percentage will be different from Space Station or Shuttle. Thus flammability of clothing must be revisited.

In several industrial fields, the integration of functions is a key technology to enhance the efficiency of components in terms of performance to mass/volume/cost ratio. Concerning the space industry, in the last few years the trend in spacecraft design has been towards smaller, light-weight and higher performance satellites with sophisticated payloads and instrumentation. Increasing power density figures are the common feature of such systems, constituting a challenging task for the Thermal Control System. The traditional mechanical and thermal design concepts are evidencing their limits with reference to such an emerging scenario.

After launch and activation activities, the Columbus module started its operational life on February 2008 providing resources to the internal and external experiments. In March 2008 two US Payloads were successfully installed into Columbus Module: Microgravity Sciences Glovebox (MSG) and a US payload of the Express rack family, Express Rack 3, carrying the European Modular Cultivation System (EMCS) experiment. They were delivered to the European laboratory from the US laboratory and followed few months later by similar racks; Human Research Facility 1 (HRF1) and HRF2. The following paper provides an overview of US Payloads, giving their main features and experiments run inside Columbus on year 2008. Flight issues, mainly on the hydraulic side are also discussed. Engineering evaluations released to the flight control team, telemetry data, and relevant mathematical models predictions are described providing a background material for the adopted work-around solutions.

The Lunar Electric Rover (LER), which was formerly called the Small Pressurized Rover (SPR), is currently being carried as an integral part of the lunar surface architectures that are under consideration in the Constellation Program. One element of the LER is the suit port, which is the means by which crew members perform Extravehicular Activities (EVAs). Two suit port deliverables were produced in fiscal year 2008: a 1-g suit port concept evaluator for functional integrated testing with the LER 1-g concept vehicle and a functional and pressurizable Engineering Unit (EU). This paper focuses on the 1-g suit port concept evaluator test results from the Desert Research and Technology Studies (D-RATS) October 2008 testing at Black Point Lava Flow (BPLF), Arizona. The 1-g suit port concept evaluator was integrated with the 1-g LER cabin and chassis concepts.

Several space agencies have announced plans to return humans to the Moon in the near future. The objectives of these missions include using the Moon as a stepping-stone towards crewed missions to Mars, to test advanced technology, and to further exploration of the Moon for scientific research and in-situ resource utilization. To meet these objectives, it will be necessary to establish and operate a lunar base. As a result, a wide variety of tasks that may pose a number of crew health and safety risks will need to be performed on the surface of the Moon. Therefore, to ensure sustainable human presence on the Moon and beyond, it is essential to anticipate potential risks, assess the impact of each risk, and devise mitigation strategies. To address this, a nine-week intensive investigation was performed by an international, interdisciplinary and intercultural team on how to maximize crew safety on the lunar surface through a symbiotic relationship between astronauts and robots.

The focus of this research is to perform a detailed investigation of the tradeoffs between mass, efficiency, service factor (SF), power factor (PF), and cost of commercially available induction machines (IMs). To support this effort, data from a large number of IMs is used to establish Pareto-optimal fronts between these competing objectives. From the Pareto-optimal fronts, relatively straightforward models are formulated for the mass versus loss, cost versus loss, SF versus mass, PF versus cost. Parameters of the models are obtained using a genetic algorithm (GA).

Boeing has contracts for military application of twin engine airplanes generically identified in this paper as the MX airplane. Unlike previous derivatives, the MX airplanes are produced with a streamlined manufacturing process to improve cost and schedule performance. The final assembly of each MX airplane includes a series of integration tests, called factory functional tests (FFTs), which are modified from those of typical commercial versions and verify correctness of equipment installation and basic functionalities. Two airplanes have been through the production line resulting in a number of FFT lessons learned. Addressed are the power distribution lessons learned: 1) the expanded coverage of the basic automated power-on generation system test, 2) the need for a manual wire continuity test, 3) salient features of the power distribution tests, and 4) keys to make first pass power distribution test smooth and successful.

Extended-duration space missions entailing expanded crew sizes and activities will produce a need for habitats that combine advantages of conventional hard/fixed and soft/deployable structures. Rigid modules enable pre-integration of utility and equipment systems prior to launch and apply proven technologies. Soft pressure vessels can be compacted to optimize launch payload volume and habitable volume/mass efficiencies, but impose hardware integration challenges, operational readiness requirements, and long-term structural performance uncertainties. This paper discusses concepts and applications that incorporate both approaches. Examples draw upon research and design investigations undertaken by SICSA in support of a NASA-sponsored study conducted by two independent teams, one headed by Boeing, and the other by ILC-Dover. SICSA had key roles in developing overall configuration architectures for both teams.

The 30 month COMET project aims to overcome the challenges facing European manufacturing industries by developing innovative machining systems that are flexible, reliable and predictable with an average of 30% cost efficiency savings in comparison to machine tools. From a conceptual point of view, industrial robot technology could provide an excellent base for machining being both flexible and cost efficient. However, industrial robots lack absolute positioning accuracy, are unable to reject disturbances in terms of process forces and lack reliable programming and simulation tools to ensure right first time machining, once production commences. These three critical limitations currently prevent the use of robots in typical machining applications. The COMET project is co-funded by the European Commission as part of the European Economic Recovery Plan (EERP) adopted in 2008.

The 30 month COMET project aims to overcome the challenges facing European manufacturing industries by developing innovative machining systems that are flexible, reliable and predictable with an average of 30% cost efficiency savings in comparison to machine tools. From a conceptual point of view, industrial robot technology could provide an excellent base for machining being both flexible and cost efficient. However, industrial robots lack absolute positioning accuracy, are unable to reject disturbances in terms of process forces and lack reliable programming and simulation tools to ensure right first time machining, once production commences. These three critical limitations currently prevent the use of robots in typical machining applications. The COMET project is co-funded by the European Commission as part of the European Economic Recovery Plan (EERP) adopted in 2008.

The term “productivity” all too often has becomes a buzz-word, ultimately diminishing its perceived importance. However, productivity is the major concern of any team, and therefore must be defined to gain an appropriate understanding of how a system is actually working. Here, productivity means the level of contribution to the throughput of a system such as defined in the Theory of Constraints. In the field of space exploration, the throughput is the number of milestones of the mission accomplished as well as the potential survival during extreme events (due to failures or other unplanned events). For a time tasks were accomplished by expert individuals (e.g., an astronaut), but recently team structures have become the norm. It is clear that with increased mission complexity, “no single entity can have complete knowledge of or the abilities to handle all matters” [10].

The need for efficient manufacturing approaches has emerged with the increasing usage of composites for structural components in commercial aviation. Resin Transfer Molding (RTM), a process where a fiber preform is injected with resin into a closed tool, can achieve high fiber content required for structural components as well as improved dimensional accuracy since all surfaces are controlled by a tool surface. Moreover, RTM is well suited for parts that can be standardized throughout the aircraft, such as a fuselage frames and stringers. The objective of this investigation is to develop a preforming approach for a C-Shaped Fuselage frame. Two approaches are proposed: tri-axial braiding and hand lay-up of Non-Crimp Fabrics. The fiber architecture of the basic materials as well as the complete preforms is explained. The necessary preforming operations are detailed. The quality control measurement of fiber orientation and thickness are presented.

This paper presents a set of numerical computations with different turbulence model on an air jet flowing tangentially over the curved surface. It has been realized that jet deflection angle and the corresponding thrust are important parameter to determine with great care. Through the grid independence analysis, it has been found that without resolution of the viscous sub-layer, it is not possible to determine the computationally independent angle of jet deflection and boundary layer thickness. The boundary layer analysis has been performed at different radius of curvature and at jet Reynolds number ranging from approximately about 2400-10,000. The boundary layer thickness has been determined at the verge of separation and found a relation with the radius of curvature and jet Reynolds number. The skin-friction coefficient has been also studied at the verge of separation in relation to the surface radius and jet Reynolds number.

Until recently most aircrafts, aircraft engines and landing gear as well as other aerospace equipment has been manufactured using essentially traditional mechanical, pneumatic or hydraulic power hand tools maintaining at the same time very strict processes to ensure quality and traceability to a certain level. An increased use of composites, intensified focus on quality and demand for extended traceability, as well as more accuracy, more flexibility, more productivity and more ergonomics in the tooling used during the assembly process has led to many manufacturing shops to invest into wireless battery tools as the best alternative to manufacture aircrafts now and in the future. We will detail in this paper what reasons led some pioneers to choose wireless battery technology to assemble aircrafts. We will describe from our perspective what the next steps are in solutions dedicated to the aerospace industry.

Significant efforts have been made in the research of Pulsed Detonation Engines (PDEs) to increase the reliability and longevity of detonation based propulsion systems for use in manned aircraft. However, the efficiency, durability, and low mechanical complexity of PDEs opens up potential for use in disposable unmanned-vehicles. This paper details the steps taken for producing a miniaturized pulse detonation engine at West Virginia University (WVU) to investigate the numerically generated constraining dimensions for Deflagration to Detonation Transition (DDT) cited in this paper. Initial dimensions for the WVU PDE Demonstrator were calculated using fuel specific DDT spatial properties featured in the work of Dr. Phillip Koshy Panicker, of The University of Texas at Arlington. The WVU demonstrator was powered using oxygen and acetylene mixed in stoichiometric proportions.