Search Results

The presentation describes the aerodynamic development and optimization process of the three different new models of the Audi A6/A7 family. The body types of these three models represent the three classic aerodynamic body types squareback, notchback and fastback. A short introduction of the flow structures of these different body types is given and their effect on the vehicle aerodynamic is described. In order to achieve good aerodynamic performance, the integration into the development process of the knowledge about these flow phenomena and the breakdown of the aerodynamic resistance into its components friction- and pressure drag as well as the induced drag is very important. The presentation illustrates how this is realized within the aerodynamic development process at Audi. It describes how the results of CFD simulations are combined with wind tunnel measurements and how the information about the different flow phenomena were used to achieve an aerodynamic improvement.

The optimization of the flow field around new vehicle concepts is driven by aerodynamic and thermal demands. Even though aerodynamics and thermodynamics interact, the corresponding design processes are still decoupled. Objective of this study is to include a thermal model into the aerodynamic design process. Thus, thermal concepts can be evaluated at a considerably earlier design stage of new vehicles, resulting in earlier market entry. In a first step, an incompressible CFD code is extended with a passive scalar transport equation for temperature. The next step also accounts for buoyancy effects. The simulated development of the thermal boundary layer is validated on a hot flat plate without pressure gradient. Subsequently, the solvers are validated for a heated block with ground clearance: The flow pattern in the wake and integral heat transfer coefficients are compared to wind tunnel simulations. The main section of this report covers the validation on a full-scale production car.

The statistical energy analysis (SEA) is widely used to support the development of the sound package of cars. This paper will present the preparation of a model designed to investigate the sound package of the new Audi A3 and associated correlation against measurements. Special care was given during the creation of the model on the representation of the structure to enable the analysis of structure borne energy flow on top of the classical airborne analysis usually done with SEA. The sound package was also detailed in the model to allow further optimization and analysis of its performance. Two real life load cases will be presented to validate the model with measurements. First, the dominating powertrain and a second load case with dominating rolling noise. An analysis of the contribution of the different source components and a way to diagnose the weak paths of the vehicle will be presented. The focus of this investigation is the application of optimally adjusted treatment.

During series production of modern combustion engines a major challenge is to ensure the correct operation of every engine part. A common method is to test engines in end-of-line (EOL) cold test stations, where the engines are not fired but tugged by an electric motor. In this work we present a physically based 0D model for dynamic simulation of combustion engines under EOL test conditions. Our goals are the analysis of manufacturing faults regarding their detectability and the enhancement of test procedures under varying environmental conditions. Physical experiments are prohibitive in production environments, and the simulative approach reduces them to a minimum. This model is the first known to the authors exploring advanced engine test methods under production conditions. The model supports a wide range of manufacturing faults (with adjustable magnitude) as well as error-free production spread in engine components.

Brake Particle Emission (BPE) is gaining considerable importance for the friction brake and automotive industry. So far no common approach or legislation for BPE characterization exists although many activities in this field have been started during the last years. Taking this into account, the authors carried out a joint measurement campaign to investigate a new approach regarding the sampling location using a brake dynamometer. During preliminary investigations the influence of the cooling air quality has been examined and a sampling point position validation has been carried out. At first the stabilization behavior for repeated test cycles and variations of volumetric air flow rates are analyzed. As a next step the role of volatile particle emissions is determined. Subsequently, the influence of load history and friction power is studied. Finally results in terms of the role of high temperature applications are presented.

Good lighting is crucial for safe driving at night. Unfortunately, many parameters are contributing to the final result of the individual tolerances of car body, dynamics and headlamp: the resulting aim. The paper will analyze individual tolerance contributors from car body parameters like load, tire pressure, suspension as well as temperature parameters of chassis and plastic parts. The investigation shows that the headlight aim can fluctuate in a worst case scenario more than ±0.3°.

The paper will describe actual investigations on safety improvements by new lighting functions. Especially the new chance of projections on the road surface either by simple reflector technology or by modern signature and pattern projection will be investigated. Different prototype patterns will be checked by a set of new parameters, e.g. reaction time to signals, clear understanding, minimum and optimum visual contrasts. The results show that high contrasts and dynamic effects are most effective.

Wheels on passenger vehicles cause about 25% of the aerodynamic drag. The interference of rims and tires in combination with the rotation result in strongly turbulent wake regions with complex flow phenomena. These wake structures interact with the flow around the vehicle. To understand the wake structures of wheels and their impact on the aerodynamic drag of the vehicle, the complexity was reduced by investigating a standalone tire in the wind tunnel. The wake region behind the wheel is investigated via Particle Image Velocimetry (PIV). The average flow field behind the investigated wheels is captured with this method and offers insight into the flow field. The investigation of the wake region allows for the connection of changes in the flow field to the change of tires and rims. Due to increased calculation performance, sophisticated computational fluid dynamics (CFD) simulations can capture detailed geometries like the tire tread and the movement of the rim.

The paper describes the aerodynamic development and optimization process of the three different new models of the Audi A6/A7 family. The body types of these three models represent the three classic aerodynamic body types squareback, notchback and fastback. A short introduction of the flow structures of these different body types is given and their effect on the vehicle aerodynamic is described. In order to achieve good aerodynamic performance, the integration into the development process of the knowledge about these flow phenomena and the breakdown of the aerodynamic resistance into its components friction- and pressure drag as well as the induced drag is very important. The paper illustrates how this is realized within the aerodynamic development process at Audi. It describes how the results of CFD simulations are combined with wind tunnel measurements and how the information about the different flow phenomena were used to achieve an aerodynamic improvement.

Brake particle emissions as a part of non-exhaust emissions are becoming more and more relevant, various international research activities can be stated. Also from the legislation side, first hints are given in regards of possible regulations. One possible approach for the reduction of brake particle emissions deals with the collection of those particles close to the foundation brake. The presented paper will follow such an approach and give some insights. In a first step, the technical layout is described for bench and vehicle testing. While for bench testing a PMP-like style of the setup could be chosen, the vehicle test setup is oriented on conventional wheel dust measurements. Hence, presented results of laboratory testing are dealing with PN and PM measurements. Also the impact on particle size distribution is discussed. It can be stated, that the particle collecting system is able to improve PN and PM emissions. Additionally, ultra-fine particles are almost eliminated.

Hybrid vehicle simulation methods combine physical test articles (vehicles, suspensions, etc.) with complementary virtual vehicle components and virtual road and driver inputs to simulate the actual vehicle operating environment. Using appropriate components, hybrid simulation offers the possibility to develop more accurate physical tests earlier, and at lower cost, than possible with conventional test methods. MTS Systems has developed Hybrid System Response Convergence (HSRC), a hybrid simulation method that can utilize existing durability test systems and detailed non-real-time virtual component models to create an accurate full-vehicle simulation test without requiring road load data acquisition. MTS Systems and Audi AG have recently completed a joint evaluation project for the HSRC hybrid simulation method using an MTS 329 road simulator at the Audi facility in Ingolstadt, Germany.

The ridemeter is a development tool that provides a predictive value for subjectively perceived ride quality on the basis of objective measured values. After years of preliminary investigations it was possible to make the link between the subjective driving experience and objective measured data. Intensive validation of the tool known as the ridemeter enables it to obtain meaningful results, which meet with a high degree of acceptance from the development engineer. The ridemeter is capable of providing calculated assessments for different vehicle concepts on different roads. The ridemeter is used on general road tests, on test runs on the AUDI proving ground, on our test rigs and in simulation. Areas of application include benchmark investigations, optimisation steps for suspension components and systems, and the setting out of limit values and tolerance curves in specifications for future vehicles.

For car manufacturers, seating comfort is becoming more and more important in distinguishing themselves from their competitors. There is a simultaneous demand for shorter development times and more comfortable seats. Comfort in automobile seats is a multi-dimensional and complex problem. Many current sophisticated measuring tools were consulted, but it is unclear on which factors one should concentrate attention when measuring comfort. The goal of this paper is to find a model in order to predict the overall seating discomfort based on body area ratings. Besides micro climate, the pressure distribution appears to be the most objective measure comprising with the clearest association with the subjective ratings. Therefore an analysis with three different test series was designed, allowing the variation of pressure on the seat surface. In parallel the subjects were asked to judge the local and the overall sensation.

In the production of brake disc pads, powder mixes containing, metal chips, filling agents, and abrasive materials, as well as phenolic resins are processed and molded to a back plate by way of pressure and temperature. These molded disc pads reach their final strength through additional thermal treatment such that the phenolic resins approach “full cure”. This production process leads to anisotropic, viscoelastic, and to a certain extent heterogeneous materials which are - like the brake system- increasingly subject to even greater demands. E.g. apart from tribological characteristics, more and more focus is placed on structure-mechanical properties to improve the braking comfort.

The following document offers insight into the work of the MOST Cooperation. Now that MOST is on the road, a short overview of five years of successful collaborative work of the partners involved and the results achieved will be given. Emphasis is put on the importance of a shared vision in combination with shared values as a prerequisite for targeted collaborative work. It is also about additional key success factors that led to the success of the MOST Cooperation. Your attention will be directed to the way the MOST Cooperation sets and achieves its goals. And you will learn about how the organization was set-up to support a fast progression towards the common goal. The document concludes with examples of recent work as well as an outlook on future work.

This paper shall give an idea of a lighting strategy a car company could have decided in an senior management circle. It is a medium to long term approach dealing with styling, design, innovation, quality and environmental aspects. Cost influences will be pointed out. It gives examples how different target conflicts could be handled and how or where to find mutual gain. Some “natural” conflicts between styling, engineering and marketing in car development are discussed. The different roles a car company could play in the development process will be shown. Is a car company responsible for the application of parts only or should it take the development leadership? And how could it be in future? Chances and risks will be pointed out.

The paper describes the integration of Complexity Management into the design cycle of an Automobile Manufacturer. It explains the reasons why most Automobile Manufacturers lack effective processes of dealing with complexity issues and introduces a holistic methodology for systematic and successful avoidance and control of unnecessary complexity. The paper provides an overview on the methods and tools necessary for the successful application of the above principle and is based on the experiences made with the implementation of the concept into the Audi AG product development process.

Computational Fluid Dynamics (CFD) is state of the art in the aerodynamic development process of vehicles nowadays. With increasing computer power the numerical simulations including meshing and turbulence modeling are capturing the complex geometry of vehicles and the flow field behavior around and behind a bluff body in more detail. The ultimate goal for realistic automotive simulations is to model the under-hood as well. In this study vehicle simulations using the finite volume open source CFD program OpenFOAM® are validated with own experiments on a modified generic quarter-scale SAE body with under-hood flow. A model radiator was included to take account of the pressure drop in the under-hood compartment. Force and pressure measurements around the car, total-pressure and hot-wire measurements in the car flow field and surface flow patterns were simulated and compared with the experiment.

Headlamp performance has changed in the last 20 years significantly. Sealed beam lamps were replaced by VHAD, VOR and VOL types, but still the optical input in terms of tungsten filament based luminous flux remained more stable. With Xenon discharge lamps and now LED the performance of a headlamp may vary strongly and thus the optical performance. Various rating systems have been developed to assess the quality of lamps and light distribution, some based on laboratory based data, some based on static or dynamic street test drives with online measurements and assessments. Basic interest is to understand the performance of the light for a real driver. This article will discuss the influence parameters on achieving a repeatable and precise rating as well as the outer influence that creates glare and varying seeing distance. Mostly mechanical headlamp and car conditioning will influence the result as well as human factors like aiming precision and aiming tolerances.

The large wind tunnel at the Technische Universität München was upgraded by integrating a modular single-belt system, which enables the simulation of moving ground conditions for ground vehicle testing. Central part of this system is its large belt that moves at a maximum speed of 50 m/s. This belt not only simulates the relative motion between the model vehicle under investigation and the floor, but also drives the model's wheels. Due to its size, the wind tunnel facility is suited for testing 40%-scaled models of typical passenger cars, which are held in place by a newly designed model support system consisting of five struts: One strut to support the body of the model and four struts to hold the model's wheels on top of the moving belt. Another crucial step in upgrading the wind tunnel was to install a boundary layer scoop system to reduce the thickness of the boundary layer approaching the moving belt.