Search Results

The objective of this paper is to propose that the automotive engineering “legacy” approach of assuming that vehicle electrical return paths using conductive structural components have zero (0) ohms of impedance, needs to be reviewed. The process in this review consists of the development of an equivalent circuit composed of both real (“resistive”) and reactive elements (due to inductance and capacitance). This issue needs to be addressed due to the increased complexity of electrical and electronics systems in vehicles and the use of the vehicle structural (such as chassis, frame, or bracket) components to provide a path for the return of electrical power and/or signals as a way to eliminate additional wiring manufacturing issues, cost, and weight contribution to a vehicle.

Aromatics, cetane number, density, and lubricity of a large number of retail diesel fuel samples were compared before, during, and after the switch from low sulfur to ultra low sulfur diesel fuel. Also, sulfur and nitrogen speciation was done on a small set of samples to determine the changes in heterocyclic compounds as refiners made the switch. For ultra low sulfur fuel, total aromatics decreased substantially, density decreased slightly, cetane number increased by about 1 - 2 numbers, and lubricity (wear scar) improved slightly relative to low sulfur diesel fuel. Speciation results showed that hydrotreating eliminated thiophenes and benzothiophenes from the fuel. The only sulfur species remaining were dibenzothiophenes, and these were present at very low part per million levels. Nitrogen compounds in the form of carbazoles were either eliminated or reduced to low part per million levels.

The extent to which the stress history of a component is non-proportional and out-of-phase can strongly influence the accuracy of the fatigue-life prediction. Phenomenological multiaxial fatigue models are more or less accurate depending upon the extent to which the stress or strain history is non-proportional and out-of-phase. Herein, scalar measures are introduced for characterizing the non-proportional and out-of-phase extent of any stress or strain history. These scalar measures are used to characterize the stress history of a an overhead-cam cylinder-head when subjected to severe cyclic operating thermal loads.

American Society for Testing and Materials (ASTM) Sequence III Engine Oil Certification Tests have been used for the past forty-five years to evaluate lubricant performance characteristics for valvetrain wear, viscosity increase, and piston deposit formation. Minimum performance standards for passenger car light duty gasoline engine oil categories are set by the International Lubricants Standardization and Approval Committee (ILSAC) (1) and the American Petroleum Institute (API) (2). This paper describes the development of the new ASTM Sequence IIIG Engine Oil Certification Test for use in evaluating the performance characteristics of engine oils meeting the next generation, low sulfur, low phosphorus, ILSAC GF-4 and API licensing requirements.

Zinc dithiophosphate, or ZDP, for over 60 years has been used as an additive in engine oils to provide wear protection and oxidation stability in an efficient and cost effective manner. Unfortunately, ZDP contains phosphorus, and phosphorus is a widely known and accepted poison of automotive catalysts and other emissions system components. Because of this, phosphorus (and ZDP) levels in automotive engine oils have been gradually reduced by about 35% over the last 10-15 years, and further reductions are likely in the future. This paper traces the history of ZDP use in automotive engine oils, and addresses the issue of how much (if any) ZDP is actually required to provide wear protection in today's, as well as yesterday's, engines. The focus in the paper is on wear (including scuffing) protection, and not on the other aspects of ZDP performance, such as providing oxidation stability of the oil.

Bench tests are often less expensive and faster than vehicle tests. However, correlation between bench tests and the engine needs to be proven, otherwise bench tests may be misleading. This investigation explored the relationships between bench wear test results and engine results from short-trip driving tests for a variety of conditions: fresh vs. used oil, different methods for assessing wear, and chemical effects such as oil contamination and differences in the fuel. There was a negative correlation between bench tests with fresh oil compared to vehicle test results with used oil, which suggests that bench wear characteristics of fresh engine oil should not be used to determine engine wear rates under the conditions tested here. Statistical analysis of bench test wear rates with used engine oil, compared to engine wear measurements, indicated that the trends were in an appropriate direction, with some scatter in the results.