Search Results

NVH targets for future vehicles are often defined by utilizing a competitive benchmarking vehicle in conjunction with an existing production and/or reference vehicle. Mode management of full vehicle modes is one of the most effective and significant NVH strategies to achieve such targets. NVH dynamic characteristics of a full vehicle can be assessed and quantified through experimental modal testing for determination of global body mode resonance frequency, damping property, and mode shape. Major body modes identified from full vehicle modal testing are primarily dominated by the vehicle's body-in-white structure. Therefore, an estimate of BIW modes from full vehicle modes becomes essential, when only full vehicle modes from experimental modal testing exist. Establishing BIW targets for future vehicles confines the fundamental NVH behavior of the full vehicle.

Random incidence sound absorption measurements of automotive components such as floor carpets, seats, headliners and hoodliners are important during the design and development of noise control treatments in a vehicle. Small volume reverberation rooms [1]1 have been widely used in practice to determine the absorption properties of those components. The SAE Acoustical Materials Committee has organized a task force to develop a standard procedure for measuring random incidence sound absorption properties of flat samples, as well as automotive components in small reverberation rooms. Statistical analysis and correlation study between large reverberation rooms and small reverberation rooms of flat samples using data acquired from a recent round robin study were reported in SAE Paper 2005-01-2284 [2, 3].

Buffeting is a wind noise of high intensity and low frequency in a moving vehicle when a window or sunroof is open and this noise makes people in the passenger compartment very uncomfortable. In this paper, side window buffeting was simulated for a typical SUV using the commercial CFD software Fluent 6.0. Buffeting frequency and intensity were predicted in the simulations and compared with the corresponding experimental wind tunnel measurement. Furthermore, the effects of several parameters on buffeting frequency and intensity were also studied. These parameters include vehicle speed, yaw angle, sensor location and volume of the passenger compartment. Various configurations of side window opening were considered. The effects of mesh size and air compressibility on buffeting were also evaluated. The simulation results for some baseline configurations match the corresponding experimental data fairly well.

This paper discusses an analytical tool that has been developed to predict what types of interior sound package treatments may be necessary in a truck cab to meet a predetermined target sound level at the driver location. The steps that were taken to develop this tool involved a combination of experimental measurement and analytical based studies. Measurements were conducted to identify the acoustic strengths of the major noise paths through which sound travels from outside to inside the truck. These findings were then used to develop a sound package that reduced the vehicle interior noise to meet the target. Measurements were primarily made on a chassis roll dynamometer with final road verification to substantiate the dynamometer data. Data obtained from these measurements were also used in the analytical model that predicts the impact of various acoustics parts in the vehicle, and has the capability to optimize the sound package treatment in the vehicle.

Once the design of a door sheetmetal and accessories is confirmed, the acoustics of the door system depends on the sound package assembly. This essentially consists of a watershield which acts as a barrier and a porous material which acts as an absorber. The acoustical performance of the watershield and the reverberant sound build-up in the door cavity control the performance. This paper discusses the findings of a design study that was developed based on design of experiments (DOE) concepts to determine which parameters of the door sound package assembly are important to the door acoustics. The study was based on conducting a minimum number of tests on a five factor - two level design that covered over 16 different design configurations. In addition, other measurements were made that aided in developing a SEA model which is also compared with the findings of the results of the design study.

High levels of broadband random noise are generally required for conducting sound transmission loss and sound absorption tests within reverberation rooms. However, the sound system components such as loudspeakers, amplifiers, and other elements are often selected with little consideration of the audio engineering principles that govern device as well as system operation. This paper will explore some of the requirements for reverberation room sound systems starting with the acoustical power spectrum needed to overcome the transmission loss of high performance barrier assemblies, the background noise in the receiving room, the background noise floor of measuring instruments, and air absorption within the reverberation room.

Typical automotive sound package components are usually characterized by their absorption coefficients and their acoustic power-based insertion loss. This insertion loss (IL) is usually obtained by subtracting the transmission loss (TL) of a bare flat steel plate from the TL of the same plate covered with the trim material. While providing useful information regarding the performance of the component, air-borne insertion loss is based solely on acoustic excitations and thus provides very little information about the structure-borne performance of the component. This paper presents an attempt to introduce a standard procedure to define the power-based structure-borne insertion loss of sound package components. A flat steel plate is excited mechanically using a shaker. Different carpet constructions are applied on the plate and tested. Based on velocity measurements, a force transducer and intensity probe, the mechanical input and the acoustic radiated power are obtained.

Damping treatments have been used in reducing structure-borne noise in vehicles for many years. Although sheet based heat bondable mastic products (often called melt sheets) are quite common in the industry, sprayable products have several advantages and have been cited in the literature. This paper discusses findings of numerous structure-borne noise studies that were conducted on sprayable materials with different base-chemistries. The analyses show that a waterborne product is the most advantageous damping treatment in an automotive assembly process. The results also reveal that application of this product provides effective damping treatment as well as reduces structurally radiated noise.

In the automotive industry, random incidence sound absorption tests are conducted on flat material samples as well as on finished components such as headliners, seats, and floor carpet systems. This paper discusses a feasibility study that is being pursued by an SAE task force, under the direction of the Acoustical Materials Committee, to develop a small volume reverberation room test method for conducting random incidence sound absorption tests. This method has the potential to be suitable for flat material and component testing. A round-robin test program is being conducted to determine variability due to test procedures, room size differences and laboratory differences. The paper discusses the selection of test samples and provides an update on the findings of the round-robin test study.

The use of sealant materials to improve interior acoustics has increased significantly in todays automobiles. One such application is to use expandable sealant materials in rails, pillars, and cavities to reduce noise propagation. However, there is no standardized method for evaluating the acoustical performance of these materials. This paper reviews the basics of noise control engineering and discusses a proposed laboratory based test methodology that has been developed for properly evaluating the acoustical performance or expandable sealant materials. The test method is intended to simulate actual applications so that different materials can be evaluated to achieve optimum acoustical performance within a channel representing the rails or pillars in automobiles.

Advances in vehicle noise control are leading the automotive industry to place increasing emphasis on weatherseals to block exterior noise. As a result, properly evaluating the acoustical performance of automotive weatherseals is of increasing importance. There is no current specific standard for this testing. Rather, there has been reliance on adaptations of SAE Standard 51400 “Laboratory Measurement of the Airborne Sound Barrier Performance of Automotive Materials and Assemblies” by testing laboratories. However, the 51400 standard addresses testing of flatstock materials and does not readily lend application to pre-formed parts such as weatherseals. For this reason, adaptation of the standard can vary significantly from facility to facility and manufacturer to manufacturer. These differences can be significant and can render comparisons between test results on competing materials very difficult.

The purpose of this paper is to identify various concerns that need to be evaluated prior to the design and construction of a reverberation chamber, such that the chamber can be used for various automotive related acoustical measurements. Some of the concerns involve issues such as room shape and size, the degree of sound and vibration isolation required, the use of conventional building materials versus traditional massive construction, construction cost, and the performance requirements for the test noise generation system. Various uses of a reverberation chamber include random incidence sound absorption measurements, small sample sound transmission loss measurements, vehicle insertion loss tests, dash panel, door, and other “buck” evaluation tests, and sound power level measurements of small automotive components and devices. These uses have differing and in some cases conflicting requirements that compete in the selection of room design parameters.

The presence of any weak paths or leakage limits the best design and the acoustical performance of a sound package system in a vehicle. Techniques to predict the response at the design level could help in improving the performance of the sound package system. This paper discusses the development, verification, and implementation of an analytical technique for predicting the acoustical performance of a sound package system based on the principles of sound transmission coefficient and the surface area covered by each sub-system. This technique is especially suitable for predicting the acoustical performance of a weak path created by passthroughs or plugs in a sound package system. Initially, a simple system was developed and studied to verify the model. The predicted values were compared with the measured values. Based on the comparison, different parameters were identified and modified such that the model agrees closely with the measured data.

This paper discusses a development procedure that was used to evaluate the acoustical performance of one type of dashpanel construction over another type for a given application. Two very different constructions of dashpanels, one made out of plain steel and one made out of laminated steel, were studied under a series of different test conditions to understand which one performs better, and then to evaluate how to improve the overall performance of the inferior dashpanel for a given application. The poorly performing dashpanel was extensively tested with dashmat and different passthroughs to understand the acoustic strength of different passthroughs, to understand how passthroughs affect the overall performance of the dash system, and subsequently to understand how the performance can be improved by improving one of the passthroughs.

With the ever increasing popularity of SUV automobiles, studies involving driveline specific problems have grown. One prevalent NVH problem is axle whine associated with the assembled motion transmission error (MTE) of an axle system and the corresponding vibration/acoustic transfer paths into the vehicle. This phenomenon can result in objectionable noise levels in the passenger compartment, ensuing in customer complaints. This work explores the methodology and test methods used to diagnose and solve a field axle whine problem, including the use of cab mount motion transmissibility path analysis, running modes and a detailed MTE best-of-the-best (BOB)/worst-of-the-worst (WOW) study. The in-vehicle axle whine baseline measurements including both vehicle dynamometer and on-road test conditions, along with the countermeasures of axle whine fixes are identified and presented in this paper.

Small reverberation rooms are used in common practice for determining random incidence sound absorption properties of flat materials and finished parts. Based on current small reverberation room usage in the automotive industry, there is a need for standardization that would bring about an appropriate level of consistency and repeatability. To respond to this need, a feasibility study is being pursued by an SAE task force, under the direction of the Acoustical Materials Committee, to develop a small volume reverberation room test method for conducting random incidence sound absorption tests. In addition to an accepted test method for small reverberation rooms, a data driven correlation that relates full size reverberation room absorption testing to small size reverberation room testing would be beneficial in understanding the usage of both. A Round Robin study has been underway for more than three years and will be completed in 2005.

Liquid spray applied damping materials have potential advantages over conventional sheet damping materials in automotive body panel vibration applications. In order to understand the acoustical impact, a laboratory based NVH study was conducted to compare the damping and stiffness performance characteristics of various sprayable damping materials versus the production damping treatment. Based on this comparison, a criteria was developed to select potentially viable sprayable damping materials for vehicle testing. In-vehicle tests were also performed and compared to the laboratory findings to understand how well the results correlate. This paper discusses a criteria for selecting sprayable damping materials based on bench-top tests for vehicle applications, and the potential benefits of sprayable materials.

A statistical theory is used to quantify the amount of information transmitted from a transducer (i.e., accelerometer) to the air bag controller during a vehicle crash. The amount of information relevant to the assessment of the crash severity is evaluated. This quantification procedure helps determine the effectiveness of different testing conditions for the calibration of sensor algorithms. The amount of information in an acceleration signal is interpreted as a measure of the ability to separate signals based on parameters that are used to assess the severity of an impact. Applications to a linear spring-mass model and to actual crash signals from a development vehicle are presented. In particular, the comparison of rigid barrier (RB) and offset deformable barrier (ODB) testing modes is analyzed. Also, the performance of front-mounted and passenger compartment accelerometers are compared.

Acoustical laboratories for vehicle testing have specialized requirements which differ from those for most conventional buildings and facilities. As a result, the normal design and building process takes on added dimensions which need to be carefully considered and addressed. This paper presents an overview of the process that starts with conceptualization of the laboratory and ends with the validation and qualification of the laboratory, and includes particular emphasis on the inherent peculiarities. Case studies are provided of several potential perils and pitfalls that may be encountered in the process which can adversely affect the usability of the laboratory as well as the validity and repeatability of test results obtained by that laboratory. The paper concludes with suggested courses of action which will help either to avoid or minimize the compromises that imperil the functional effectiveness of a laboratory.

This paper provides an overview of a custom software developed to obtain measurement data in a self-contained acoustic test facility system used for conducting random incidence sound absorption tests and sound transmission loss tests on small samples in accordance with SAE J2883 and J1400 standards, respectively. Special features have been incorporated in the software for the user to identify anomalies due to extraneous noise intrusion and thereby to obtain good data. The paper discusses the thoughts behind developing user-friendly algorithms and graphical user interfaces (GUI) for the sound generation, control, data acquisition, signal processing, and identifying anomalies.