Search Results

Abstract Gasoline particulate filters (GPFs) are important aftertreatment components that enable gasoline direct injection (GDI) engines to meet European Union (EU) 6 and China 6 particulate number emissions regulations for nonvolatile particles greater than 23 nm in diameter. GPFs are rapidly becoming an integral part of the modern GDI aftertreatment system. The Active Exhaust Tuning (EXTUN) Valve is a butterfly valve placed in the tailpipe of an exhaust system that can be electronically positioned to control exhaust noise levels (decibels) under various vehicle operating conditions. This device is positioned downstream of the GPF, and variations in the tuning valve position can impact exhaust backpressures, making it difficult to monitor soot/ash accumulation or detect damage/removal of the GPF substrate. The purpose of this work is to present a unique example of subsystem control and diagnostic architecture for an exhaust system combining GPF and EXTUN.

Abstract This article presents a fault diagnosis approach for roller bearing by applying the autocorrelation approach to filtered vibration measured signal. An optimal Morlet wavelet filter is applied to eliminate the frequency associated with interferential vibrations; the raw measured signal is filtered with a band-pass filter based on a Morlet wavelet function whose parameters are optimized based on maximum Kurtosis. Autocorrelation enhancement is applied to the filtered signal to further reduce the residual in-band noise and highlight the periodic impulsive feature. The proposed technique is used to analyze the experimental measured signal of investigated vehicle gearbox. An artificial fault is introduced in vehicle gearbox bearing an orthogonal placed groove on the inner race with the initial width of 0.6 mm approximately. The faulted bearing is a roller bearing located on the gearbox input shaft - on the clutch side.

Abstract Automotive-grade high-strength steels are galvanized for improved corrosion resistance. However, selective oxidation of alloying elements during annealing heat-treatment may influence the subsequent zinc (Zn) coating quality. The formation of internal and external oxides depends on the alloy composition, especially the Si/Mn ratio, and the oxygen potential of the annealing atmosphere. In this work, a dual-phase (DP) steel was intercritically annealed with varied fuel-to-air ratios in a direct-fired furnace and then galvanized in a Zn bath with 0.2 wt% Al. The type of internal and external oxides and the interfacial structures between the steel substrate, the Al-Fe-Zn inhibition layer, and the Zn coating were examined by using site-specific focused ion beam (FIB) and transmission electron microscopy (TEM).

Abstract TOC

Abstract TOC

Abstract TOC

Abstract TOC

Abstract The principal issue in choosing an energy management strategy (EMS) for hybrid electric vehicles (HEVs) has been the way of determining the optimal share of electric energy in hybrid drive. In this article, a novel EMS is proposed that, along with maximum engine efficiency in the hybrid drive, can optimize the share of battery energy for the maximum efficiency of vehicle power train expanded with an imaginary power plant that, by delivering the electric energy to a grid, feeds the vehicle battery. It is proved that the expanded power train efficiency has the local maximum for a wide range of wheel power demand. The relation between the wheel power demand in hybrid drive, the share of battery energy, and the maximum efficiency of the expanded power train is conducted offline. Downloaded to the onboard control system, it enables the operation with the instantaneously optimal share of battery energy and the control system to operate with the low computational load.

Abstract Traditionally, in combustion engine applications, metallic materials have been widely employed due to their properties: castability and machinability with accurate dimensional tolerances, good mechanical strength even at high temperatures, wear resistance, and affordable price. However, the high thermal conductivity of metallic materials is responsible for consistent losses of thermal energy and has a strong influence on pollutant emission. A possible approach for reducing the thermal exchange requires the use of thermal barrier coating (TBC) made by materials with low thermal conductivity and good thermo-mechanical strength. In this work, the effects of a ceramic coating for thermal insulation of the piston crown of a car diesel engine are investigated through a numerical methodology based on finite element analysis. The study is developed by considering firstly a thermal analysis and then a thermo-structural analysis of the component.

Abstract In this study low temperature plasma technology was applied to expand auto-ignition operation region and control auto-ignition phasing of the homogeneous charge compression ignition (HCCI) combustion. The low temperature plasma igniter of a barrier discharge model (barrier discharge igniter (BDI)) with high-frequency voltage (15 kHz) was provided at the top center of the combustion chamber, and the auto-ignition characteristics of the HCCI combustion by the low temperature plasma assistance was investigated by using a single-cylinder gasoline engine. HCCI combustion with compression ratio of 15:1 was achieved by increasing the intake air temperature. The lean air-fuel (A/F) ratio limit and visualized auto-ignition combustion process on baseline HCCI without discharge assistance, spark-assisted HCCI, and BDI-assisted HCCI were compared.

Abstract The article describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components’ light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features has been thoroughly experimentally examined.

Abstract This work focuses on the effects of the laminar flame speed (LFS) and flame stretch on the phenomenological modeling of the combustion process in spark ignition engines. The study is carried out using a 1D model of a small-size naturally aspirated SI engine, equipped with an external EGR circuit. The model, developed in GT-Power™ environment, includes advanced sub-models of the in-cylinder processes. The combustion is modeled using a fractal approach, where the burning rate is directly related to the laminar flame speed. A novel LFS correlation based on 1D chemical kinetics computations is presented and assessed with the experimentally derived Metghalchi and Keck correlation. Moreover, the effects of the flame stretch, evaluated according to an asymptotic theory, are properly considered in the combustion model.

Abstract Performing an uncertainty analysis for complex measurement tasks, such as those found in engine research, presents unique challenges. Also, because of the excessive computational costs, modeling-based approaches, such as a Monte Carlo approach, may not be practical. This work provides a traditional statistical approach to uncertainty analysis that incorporates the uncertainty tree, which is a graphical tool for complex uncertainty analysis. Approaches to calculate the required sensitivities are discussed, including issues associated with numerical differentiation, numerical integration, and post-processing. Trimming of the uncertainty tree to remove insignificant contributions is discussed. The article concludes with a best practices guide in the Appendix to uncertainty propagation in experimental engine combustion post-processing, which includes suggested post-processing techniques and down-selected functional relationships for uncertainty propagation.

Abstract This study shows the development of low-temperature and high-temperature reactions in a gasoline-fuelled compression ignition (GCI) engine realizing partially premixed combustion for high efficiency and low emissions. The focus is how the ignition occurs during the low- to high-temperature reaction transition and how it varies due to single- and double-injection strategies. In an optically accessible, single-cylinder small-bore diesel engine equipped with a common-rail fuel injection system, planar laser-induced fluorescence (PLIF) imaging of formaldehyde (HCHO-PLIF), hydroxyl (OH-PLIF), and fuel (fuel-PLIF) has been performed. This was complemented with high-speed imaging of combustion luminosity and chemiluminescence imaging of cool flame and OH*.

Abstract Mechanical friction simulations offer a valuable tool in the development of internal combustion engines for the evaluation of optimization studies in terms of time efficiency. However, system modeling and evaluation of model performance may be highly complex. A high number of interacting submodels and parameters as well as a limited model transparency contribute to uncertainties in the modeling process. In particular, model calibration and validation are complicated by the unknown effect of parameters on the model output. This article presents an advanced and model-independent methodology for identifying sensitive parameters of engine friction. This allows the user to investigate an unlimited number of parameters of a model whose structure and properties are prior unknown.

Erratum

Abstract The heat transfer phenomena in Internal Combustion Engines (ICEs) are one of the main research topics that need to be addressed to enhance the performance in terms of power, efficiency, emissions and reliability. The present study is focused on the evaluation of the in-cylinder heat fluxes through the use of Computational Fluid Dynamic (CFD) simulations, with a wall function approach. In particular, the aim of this work is to present a new fully non-isothermal wall function obtained from the one-dimensional (1-D) energy balance equation for turbulent flows in the boundary layers, specifying all the steps and assumptions which have carried to the final fully compressible formulation. The new proposed wall function has been validated against experimental data of the General Motors (GM) Pancake Engine, representative of low Brake Mean Effective Pressure (bmep) operating point, comparing the results with other existing wall functions.

Abstract One of the key factors for accurate mass burn fraction and energy conversion point calculations is the accuracy of the compression ratio. The method presented in this article suggests a workflow that can be applied to determine or correct the compression ratio estimated geometrically or measured using liquid displacement. It is derived using the observation that, in a motored engine, the heat losses are symmetrical about a certain crank angle, which allows for the derivation of an expression for the clearance volume [1]. In this article, a workflow is implemented in real time, in a current production engine indicating system. The goal is to improve measurement data quality and stability for the energy conversion points calculated during measurement procedures. Experimental and simulation data is presented to highlight the benefits and improvement that can be achieved, especially at the start of combustion.

Abstract An in-cylinder combustion analysis and a computational fluid dynamics (CFD) coolant flow analysis were performed using AVL FIRE software, which provided the heat transfer boundary conditions (HTBCs) to the temperature field calculation of the cylinder head. Based on the measured material performance parameters such as stress-strain curve under different temperatures and E-N curve, creep, and oxidation data material performance, the cylinder head-gasket-cylinder block finite element analysis (FEA) was performed. According to the temperature field calculation results, the maximum temperature of the cylinder head is 200°C that is within the limit of ALU material. The temperature of the water is more than 21.1°C below the critical burnout point temperature. The high-cycle fatigue (HCF) and thermal-mechanical fatigue (TMF) analysis of the cylinder head were performed by FEMFAT software.

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.