Search Results

Abstract With increasing demands for higher performance along with lower vehicle emissions, lightweight vehicle system construction is key to meet such demands. Suspension and transmission assemblies being the key areas for weight-reduction, we have designed a revolutionary new type of suspension system which combines the suspension links with the powertrain assembly and thus completely eliminates one suspension member. Less weight means lower fuel-consumption with improved passenger-comfort and road-holding due to reduction in unsprung mass. Elimination of a suspension link reduces the overall cost of material, machining & fabrication making our design cost-effective than existing setups. This paper deals with the design and implementation of of our concept. A working prototype is also constructed and tested which completely validates our design.

Abstract The transition of vehicle propulsion technologies away from conventional internal combustion engines toward more electrically dominant systems such as plug-in hybrid electric vehicles (PHEV) poses new challenges for vehicle thermal management systems. Especially at low ambient temperatures, consumer demand for cabin comfort as well as legislatively imposed safety considerations significantly reduce the electric driving range because only electric energy can be used for heating during emissions-free driving modes. Recent developments to find energy efficient thermal management systems for electric and plug-in electric vehicles have led to the implementation of automotive heat pump systems. As an alternative approach to meet dynamic heating demands and safety regulations, these systems use heat at a low temperature level, for example the waste heat of electric drivetrain components, to heat the passenger compartment efficiently and therefore increase the electric driving range.

Abstract Investigation of vehicle resistant forces and power losses is of crucial importance owing to current state of energy consumption in transport sector. Meanwhile, considerable portion of resistant forces in a ground vehicle is traced back to tires. Pneumatic tires are known to be a source of energy dissipation as a consequence of their viscoelastic nature. The current study aims to provide a modification to tire resistance by considering the power loss in a tire due to longitudinal slip. The modified tire resistance is comprised of rolling resistance and a newly introduced resistance caused by tire slip, called slip resistance. The physical model is chosen for parameters sensitivity study since the tractive force is described in this model via tangible physical parameters, e.g. tire tangential stiffness, coefficient of friction, and contact patch length.

Abstract The brake discs are subjected to thermal load due to sliding by the brake pad and fluctuating loads because of the braking load. This combined loading problem requires simulation using coupled thermo-mechanical analysis for design evaluation. This work presents a combined thermal and mechanical finite element analysis (FEA) and evolutionary optimization-based novel approach for estimating the optimal design parameters of the ventilated brake disc. Five parameters controlling the design: inboard plate thickness, outboard plate thickness, vane height, effective offset, and center hole radius were considered, and simulation runs were planned. A total of 27 brake disc designs with design parameters as recommended by the Taguchi method (L27) were modeled using SolidWorks, and the FEA simulation runs were carried out using the ANSYS thermal and structural analysis tool.

Abstract This article applies a new method for the evaluation and estimation of real-life energy consumption of two different thermal management systems based on driving behavior in the course of the day. Recent attempts to find energy-efficient thermal management systems for electric and plug-in hybrid electric vehicles have led to using secondary loop systems as an alternative approach for meeting dynamic heating and cooling demands and reducing refrigerant charge. However, the additional layer of thermal resistance, which influences the system’s transient behavior as well as passenger compartment comfort during cool-down or heat-up, makes it difficult to estimate the annual energy consumption. In this article, the overall energy consumption of a conventional and a secondary loop system is compared using a new method for describing actual customers’ driving behavior in the course of the day.

Abstract Power split in Fuel Cell Hybrid Electric Vehicles (FCHEVs) has been controlled using different strategies ranging from rule-based to optimal control. Dynamic Programming (DP) and Model Predictive Control (MPC) are two common optimal control strategies used in optimization of the power split in FCHEVs with a trade-off between global optimality of the solution and online implementation of the controller. This is due to the fact that DP that offers the global optimal solution requires the pre-known knowledge of the driving condition for the whole drive cycle, which makes the real-time implementation of the strategy more challenging. In this paper, both control strategies are developed and tested on a FC/battery vehicle model, and the results are compared in terms of total energy consumption. In addition, the effects of the MPC prediction horizon length on the controller performance are studied.

Abstract In this study, an attempt is made to deduce the number of teeth in the driven sprocket of a Formula SAE (FSAE) car using Optimum Lap software based on track run simulation of the car, which comes out to be 51 teeth. The sprocket material was selected as Aluminum Alloy AL-7075 T6 because of its strength-to-weight ratio. In addition to it, the generative design strategy by Fusion-360 was utilized to automatically engender the slotted sprocket design on the ground of stress induced on it during operation. Furthermore, the design was verified virtually carrying out static structural and fatigue analysis under the worst-case scenario in CAE software. The overall weight reduction achieved was around 45%. Furthermore, the center-to-center distance between the sprockets and the number of chain links required were also calculated on the basis of space constraints and the wrap angle of the sprocket.

Abstract This article presents the application of the Life Cycle Sustainability Assessment (LCSA) methodology for integrating environmental, economic, and social assessment results by the direct application of Fuzzy-Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS). The aim of this work is to test the applicability of LCSA methodology as a potential tool to support the design phase, providing solutions tailored to its application in the automotive sector. To validate the proposed procedure, two alternative design solutions for a car dashboard are used as case study. In response to the need of methods and tools for evaluating and comparing sustainability of alternative design solutions, LCSA is seen as one of the most promising method, but which needs further testing with real cases to solve some methodological challenges.

Abstract Maximum lifetime and minimum manufacturing cost for new products are the primary goals of companies for competitiveness. These two objectives are contradictory and the geometric dimensions of the products directly control them. In addition, the earlier design errors of new products are predicted, the easier and more inexpensive their rectification becomes. To achieve these objectives, we propose in this article a novel model that makes it possible to solve the problem of optimizing the lifespan and the manufacturing cost of new products during the phase of their design. The prediction of the life of the products is carried out by an energy damage method implemented on the finite element (FE) calculation by using the ABAQUS software. The manufacturing cost prediction is carried out by applying the ABC cost estimation analytical method. In addition, the optimization problem is solved by the method of genetic algorithms.

Abstract Aerodynamic optimization of the exterior vehicle shape is a highly multidisciplinary task involving, among others, styling and aerodynamics. The often differing priorities of these two disciplines give rise to iterative loops between stylists and aerodynamicists. Reduced-order modeling (ROM) has the potential to shortcut these loops by enabling aerodynamic evaluations in real time. In this study, we aim to assess the performance of ROM via proper orthogonal decomposition (POD) for a real-life industrial test case, with focus on the achievable accuracy for the prediction of fields and aerodynamic coefficients. To that end, we create a training data set based on a six-dimensional parameterization of a Volkswagen passenger production car by computing 100 variants with Detached-Eddy simulations (DES).

Abstract Catalytic converters, a primary component in most automotive emissions control systems, do not function well until they are heated substantially above ambient temperature. As the primary energy for catalyst heating comes from engine exhaust gases, plug-in hybrid electric vehicles (PHEVs) that have the potential for short and infrequent use of their onboard engine may have limited energy available for catalytic converter heating. This article presents a comparison of multiple hybrid supervisory control strategies to determine the ability to avoid engine cold starts during a blended charge-depleting propulsion mode. Full vehicle and catalytic converter simulations are performed in parallel with engine dynamometer testing in order to examine catalyst temperature variations during the course of the US06 City drive cycle. Emissions and energy consumption (E&EC) calculations are also performed to determine the effective number of engine starts during the drive cycle.

Abstract Fan cooling system of an air-cooled diesel engine is optimized using 3D CFD numerical simulation approach. The main objective of this article is to increase engine fuel efficiency by reducing fan power consumption. It is achieved by optimizing airflow rates and flow distribution over the engine surfaces to keep the maximum temperature of engine oil and engine surfaces well within the lubrication and material limit, respectively, at the expense of lower fan power. Based on basic fan laws, a bigger fan consumes lesser power for the same airflow rate as compared to a smaller fan, provided both fans have similar efficiency. Flow analysis is also conducted with the engine head and block modeled as solid medium and fan cooling system as fluid domain. Reynolds-averaged Navier-Stokes turbulence (RANS) equations were solved to get the flow field inside the cooling system and on the engine liner fins. The Moving Reference Frame approach was used for simulating the rotation of a fan.

Abstract Particulate Matter (PM) is one of the most sought-after exhaust emissions from Heavy-Duty Diesel Engines (HDDEs) to reduce. Several regulations in Europe and North America have led the way in drastically reducing PM of both on-road and off-road engines through stringent adoption of Diesel Particulate Filters (DPFs) and advanced combustion techniques. The effects of these advanced aftertreatment systems were studied using standardized testing procedures and equipment. While PM is defined as a “single” criteria pollutant, its complex structure entails several chemical compounds and molecules, displaying a whole spectrum of particle sizes. In addition, the morphology of some volatile compounds is shown to be affected by the interaction with background air during exhaust dilution and cooling.

Abstract The increased market penetration of hybrid electric powertrains in medium heavy-duty (MHD) applications has provided a novel platform for vehicle research. One example of such a platform is the MHD parallel hybrid truck developed by Odyne Systems, LLC. In collaboration with Odyne Systems, LLC and the Department of Energy (DOE), Oak Ridge National Laboratory (ORNL) developed a validated vehicle plant model for this truck and tested the Odyne powertrain in a hardware-in-the-loop (HIL) environment. While testing in the HIL environment, the effects of reduced engine load, and thus catalyst heating, on the selective catalytic reduction (SCR) catalyst produced diminished hybrid improvement as the level of energy storage usage increased. This article will discuss these results and the potentially unforeseen interactions with modern aftertreatment systems when hybridizing conventional powertrains.

Abstract Recent research has demonstrated that gasoline compression ignition (GCI) can improve the soot-oxides of nitrogen (NOx) trade-off of conventional diesel engines due to the beneficial properties of light distillate fuels. In addition to air handling and aftertreatment, fuel systems also require further development to realize the potential efficiency and emissions benefits of GCI. Injector one-dimensional (1-D) hydraulic modeling is an important design tool used for this purpose. The current study is a continuation of prior work that used computed physical fuel properties and hydraulic models to accurately simulate high-pressure injection behavior relevant to GCI. With respect to fuel characteristics for the model, physical properties were validated by direct comparison to measurements at temperatures and pressures reaching 150°C and 2500 bar, respectively.

Abstract This article describes the application of Reinforcement Learning (RL) with an embedded heuristic algorithm to a multi-objective hybrid vehicle optimization. A multi-objective optimization problem (MOP) is defined as a minimization of total energy consumption and trip time resulting from optimal control of vehicle speed over a known route. First, a computationally efficient heuristic optimization algorithm is formulated to solve the MOP for multiple traffic scenarios. Then, the off-line integration of RL is applied to the heuristic optimization algorithm process and utilized to solve the MOP. Finally, the online optimization capability of the machine learning algorithm is discussed, as well as its extension to the vehicle routing problem and the hybrid electric vehicle. The specific scenario investigated is where a generic vehicle begins a trip on a one-lane highway. The length of the highway and the number of vehicles and traffic signals on the road are generic as well.

Abstract With highway vehicles using over 20% of the total energy consumption in the United States, making strides in improving their fuel economy will positively influence the nation’s environmental impact. One methodology to accomplish this outcome is by reducing vehicle weight. In this regard, since the internal combustion (IC) engine is a major contributor to the mass of an automobile, it is an ideal area to target. Prior efforts in this area include using alternative materials (e.g., aluminum or magnesium) to decrease weight. Here, additive manufacturing (AM) is an appealing option due to its freedom from typical manufacturing constraints and the ability to produce highly optimized designs using nonconventional powertrain materials (e.g., titanium). The use of AM has the potential to increase reliability, improve performance, decrease production cost, and possibly minimize the number of parts.

Abstract As bicycle design continues to develop, consumers are not satisfied with just the convenience and power-saving features of bicycles, but they also demand a fancy appearance. To achieve dramatic deforming of bike frames, an extreme high-profile difference is required. Thus, this study used rotary swaging, which is the best forging method among shrink forming processes, as the preforming process. The tube diameter reduction rates of 0.28 and 0.31 were set as the main parameters, and the effects of feeding speed, feeding method, and friction factor on the formed tube were analyzed. The results indicated that a higher feeding speed results in a lower rate of tube thickness increase and a lower friction factor results in a lower rate of tube thickness increase. Regarding the effects of feeding methods, the automatic feeding method yielded better surface roughness than the manual method.

Abstract Uncertainties in design represent a considerable industrial stake. Controlling the reliability and robustness of a mechanical system at the level of design has become necessary in order to control these uncertainties. Using the theory of probabilistic design optimization, the present work reports on the application of the concept of reliability-based robustness on minimizing the weight of a planetary gear train (PGT). The optimum combination of reliability and robustness for the minimum weight of the PGT was found using an optimization algorithm based on Particle Swarm Optimization (PSO) and Monte Carlo Simulation (MCS). The algorithm was developed by combining the propagation of uncertainties with the optimization of the function objective within a single probabilistic model. The results show that a reliability-based robust design offers a better alternative to the traditional deterministic design models.

Abstract The preeminent obligation of the automotive engineers, while designing a car, is to assure the driver’s well-being during any kind of impact by suppressing intrusions into the cockpit or minacious deceleration levels. Technologists and designers are advancing various modern active and passive safety systems to augment vehicle occupants’ safety. To mitigate the research and development expenditure in time and money, it is recommended to utilize computational crash simulations for the early evaluation of safety behavior under vehicle impact tests. Therefore, in this research study, an attempt is made to simulate crashworthiness and design the impact attenuator utilized in Formula SAE vehicles to absorb the kinetic energy of a car during a frontal collision. Closed-cell aluminum foam is selected as its material because of its less density than solid metals and ability to undergo large deformations at almost constant load.