Search Results

The use of early and late injection diesel Low Temperature Combustion (LTC) strategies in the low to mid load operating range are becoming increasingly popular options for production diesel engines to reduce oxides of nitrogen (NOx) and particulate matter (PM) emissions. Although opacity-based filter smoke number (FSN) PM measurements in these operating conditions have been reduced to near zero for many instruments (which are standard and very useful in most engine combustion research laboratories), significant changes can still be seen in the particle size and number measurements (such as a 2.5 - 4.5 fold variation in total particle number concentration, depending on engine operating condition). The current work presents particle size distribution measurements from early to late injection timing LTC, varying the start of injection (SOI) by three crank angle degrees (CAD) per data point, for two exhaust gas recirculation (EGR) rates, 45% and 50%.

In the last two decades engine research has been mainly focused on reducing pollutant emissions. This fact together with growing awareness about the impacts of climate change are leading to an increase in the importance of thermal efficiency over other criteria in the design of internal combustion engines (ICE). In this framework, the heat transfer to the combustion chamber walls can be considered as one of the main sources of indicated efficiency diminution. In particular, in modern direct-injection diesel engines, the radiation emission from soot particles can constitute a significant component of the efficiency losses. Thus, the main of objective of the current research was to evaluate the amount of energy lost to soot radiation relative to the input fuel chemical energy during the combustion event under several representative engine loads and speeds. Moreover, the current research characterized the impact of different engine operating conditions on radiation heat transfer.

With ever-demanding emission legislations in Compression Ignition (CI) engines, new premixed combustion strategies have been developed in recent years seeking both, emissions and performance improvements. Since it has been shown that in-cylinder air flow affects the combustion process, and hence the overall engine performance, the study of swirling structures and its interaction with fuel injection are of great interest. In this regard, possible Turbulent Kinetic Energy (TKE) distribution changes after fuel injection may be a key parameter for achieving performance improvements by reducing in-cylinder heat transfer. Consequently, this paper aims to gain an insight into spray-swirl interaction through the analysis of in-cylinder velocity fields measured by Particle Image Velocimetry (PIV) when PCCI conditions are proposed. Experiments are carried out in a single cylinder optical Diesel engine with bowl-in-piston geometry.

This work investigates the particulates size distribution of reactivity controlled compression ignition combustion, a dual-fuel concept which combines the port fuel injection of low-reactive/gasoline-like fuels with direct injection of highly reactive/diesel-like fuels. The particulates size distributions from 5-250 nm were measured using a scanning mobility particle sizer at six engine speeds, from 950 to 2200 rpm, and 25% engine load. The same procedure was followed for conventional diesel combustion. The study was performed in a single-cylinder engine derived from a stock medium-duty multi-cylinder diesel engine of 15.3:1 compression ratio. The combustion strategy proposed during the tests campaign was limited to accomplish both mechanical and emissions constraints. The results confirms that reactivity controlled compression ignition promotes ultra-low levels of nitrogen oxides and smoke emissions in the points tested.

Concepts of premixed diesel Low Temperature Combustion (LTC) have been shown to be advantageous in greatly reducing engine-out nitrogen oxide (NOx) and particulate matter (PM) emissions, even below the minimum detection limit of standard opacity-based PM mass instruments. Previous research has revealed that significant changes to the PM size and number emissions still occur for changes to the LTC engine operating conditions. This work investigates the influence of reductions in intake oxygen concentration on PM (mass, size, and number), NOx, hydrocarbon (HC), and carbon monoxide (CO) emissions from select LTC engine operating conditions. Exhaust particle size distributions were measured for multiple engine operating conditions of premixed diesel LTC within a range of five intake oxygen concentrations from 9% to 13% (by volume) at three intake pressures from 1.325 to 1.6 bar.

Most of the new Diesel combustion concepts are mainly based on reducing local combustion temperatures and enhancing the fuel/air mixing with the aim of simultaneously reducing soot and NOx emissions. In this framework, Premixed Charge Compression Ignition (PCCI) has revealed as one of the best options to combine both low emissions and good combustion controllability. During last years, PCCI strategy has been widely explored using high EGR levels and different early or late injection timings to extend the ignition delay. Recently, the use of lower cetane fuels is under investigation. Despite the great quantity of research work performed, there are still some aspects related to PCCI combustion that are not completely well known. In this paper an experimental and numerical study is carried out focused on understanding the mixing and auto-ignition processes in PCCI combustion conditions using Diesel and Gasoline fuels.

Dual-mode dual-fuel combustion is a promising combustion concept to achieve the required emissions and CO2 reductions imposed by the next standards. Nonetheless, the fuel formulation requirements are stricter than for the single-fuel combustion concepts as the combustion concept relies on the reactivity of two different fuels. This work investigates the effect of the low reactivity fuel sensitivity (S=RON-MON) and the octane number at different operating conditions representative of the different combustion regimes found during the dual-mode dual-fuel operation. For this purpose, experimental tests were performed using a PRF 95 with three different sensitivities (S0, S5 and S10) at operating conditions of 25% load/950 rpm, 50%/1800 rpm and 100%/2200 rpm. Moreover, air sweeps varying ±10% around a reference air mass were performed at 25%/1800 rpm and 50%/1800 rpm. Conventional diesel fuel was used as high reactivity fuel in all the cases.

A comprehensive study is carried out in order to better understand combustion behavior in a direct injection Diesel engine working under multiple injection strategies, in particular when using post-injections. The aim of the study is to provide criteria to more easily define optimized injection strategies. During the study two main phenomena have been observed and characterized: an acceleration of the final stage of combustion and an apparent disconnection between the combustions of the two pulses (“split flame”). Thanks to the combustion acceleration phenomenon, if the post-injection is placed near enough the main injection, the end of combustion can take place even earlier compared to the case with a single main injection. In such conditions NOx emissions increase (most likely due to a higher temperature level during the last stage of combustion), but soot and specific fuel consumption decrease (due to a faster last phase of combustion).

This paper describes the optimization process of a small single-cylinder research HSDI diesel engine, starting from a conventional combustion towards split-injection low-temperature combustion. Targets for emissions, fuel consumption and combustion noise are defined with the characteristics of low temperature combustion in mind, in other words, high CO, HC and combustion noise but low soot and NOX. In this investigation the targets are defined for a medium-load working modes of a typical small four-cylinder turbo-charged diesel engine, equipped with a particulate trap and oxidation catalyst. They are introduced into an objective target function which is a guide for the optimization process. The statistical optimization procedure used is the method of consecutive screenings. With this methodology, six factors are optimized: mass distribution of the fuel injection pattern, injection pressure, combustion phasing, EGR rate, boost pressure and dwell time between injection events.

In this paper the effect of the engine load and the EGR (exhaust gas recirculation) rate on the combustion process and the pollutant emissions when using RME (rapeseed methyl-ester) is investigated. For this purpose a parametric study in a single-cylinder HSDI (high speed direct injection) engine in a wide range of operating conditions (thus trying to maximize the generality of the results) has been carried out. All the output parameters are compared with the corresponding ones for a reference diesel fuel at equivalent engine performances and operating conditions. To perform a rigorous comparison, a specific methodology has been designed based on the comparison at equivalent engine load and oxygen mass fraction in the intake manifold, so as to remove the effect of the fuel properties (derived from the different oxygen content, mainly) on the engine performances.

The work presented here focuses on the influence of pre- and post-injection on the development of the combustion process and on engine efficiency and pollutant emissions. Tests were performed with a heavy-duty 1.8 litre single-cylinder engine. The study combines performance and emissions measurements together with heat release law analysis. Four representative operating conditions from the European Steady state test Cycle (ESC) have been considered. For each one, the fuel quantity of the pre- and post-injection has been varied between 12 and 20 mg/cc, and the delay of the pre- and post-injection respect to the main injection has been modified too. With a pre-injection strategy it has been possible to reduce the fuel consumption with little soot penalty but causing an increase in NOx levels in most engine modes. The post-injection strategy has been demonstrated to be efficient in soot reduction without NOx emission and fuel consumption penalty.

The main objective of the study described in this paper is to explore the potential of different post-injection patterns, with a plain common rail system, for reduction of soot emissions in HD diesel engines. Test have been carried out in a single-cylinder engine at several critical engine operation points from the European Steady state test Cycle (ESC). At these operation points, EGR was introduced to reduce NOx emissions to a given value, and then different post-injection patterns were produced. A parametric study was performed, considering the time between injections and the post-injected fuel mass as the main variables. In every case the total injected fuel mass was kept constant. Aside from the experimental data obtained in the engine tests, a diagnosis model was applied to calculate heat release laws and other parameters depicting the combustion process.

In the past few years’ various studies have shown how the application of a highly premixed dual fuel combustion for CI engines leads a strong reduction for both pollutant emissions and fuel consumption. In particular a drastic soot and NOx reduction were achieved. In spite of the most common strategy for dual fueling has been represented by using two different injection systems, various authors are considering the advantages of using a single injection system to directly inject blends in the chamber. In this scenario, a characterization of the behavior of such dual-fuel blend spray became necessary, both in terms of inert and reactive ambient conditions. In this work, a light extinction imaging (LEI) has been performed in order to obtain two-dimensional soot distribution information within a spray flame of different diesel/gasoline commercial fuel blends. All the measurements were conducted in an optically accessible two-stroke engine equipped with a single-hole injector.

Engine-out soot emissions are the result of a complex balance between in-cylinder soot formation and oxidation. Soot is formed in the diffusion flame, just after the lift-off length (LOL). Size and mass of soot particles increase through the diffusion flame and finally they are partially oxidized at the flame front. Therefore, engine-out soot emissions depend on the amount of soot formed and oxidized inside the combustion chamber. There is a considerable amount of work in the literature on characterization of soot formation. However, there is a clear lack of published research related to the characterization of soot oxidation. Thus, the main objective of the current research is to provide more knowledge and insight into the soot oxidation processes. For this purpose, a combination of theoretical and experimental tools were used. In particular, in-cylinder optical thickness (KL) was quantified with an optoelectronic sensor that uses two-color pyrometry.

An innovative alternative to overcome the load limits of the early injection highly premixed combustion concept consists of taking advantage of the intrinsic characteristics of two-stroke engines, since they can attain the full load torque of a four-stroke engine as the addition of two medium load cycles, where the implementation of this combustion concept could be promising. In this frame, the main objective of this investigation focuses on evaluating the potential of the early injection HPC concept using a conventional diesel fuel combined with a two-stroke poppet valves engine architecture for pollutant control, while keeping a competitive engine efficiency. On a first stage, the HPC concept was implemented at low engine load, where the concept is expected to provide the best results, by advancing the start of injection towards the compression stroke and it was confirmed how it is possible to reduce NOX and soot emissions, but increasing HC and CO emissions.

In-cylinder emission control strategies, such as modifications of injection pressure and injection timing, have been used by researchers in order to reduce exhaust emissions and to comply with the legislation standards. Since some years ago post-injections have been studied and are well known as being efficient for soot emissions reduction. Although is well known that diesel gaseous and particle mass emissions have been reduced progressively over the last twenty years in response to the restrictive emission legislation and due to the application of new technologies The aim of this work is to help develop and understand the effect of the post-injection on diesel exhaust particle size distributions. The approach is to use a modern, well instrumented research engine equipped with a flexible high pressure fuel injection system. The results of this work are available to help provide guidelines for strategies to achieve reductions of the particle size distributions in diesel engines.

Ever decreasing permitted emission levels and the necessity of more efficient engines demand a better understanding of in-cylinder phenomena. In swirl-supported compression ignition (CI) engines, mean in-cylinder flow structures formed during the intake stroke deeply influence mixture preparation prior to combustion, heat transfer and pollutant oxidation all of which could potentially improve engine performance. Therefore, the ability to characterize these mean flow structures is relevant for achieving performance improvements. CI mean flow structure is mainly described by a precessing vortex. The location of the vortex center is key for the characterization of the flow structure. Consequently, this work aims at evaluating algorithms that allow for the location of the vortex center both, in ensemble-averaged velocity fields and in instantaneous velocity fields.

Many concepts of premixed diesel combustion at reduced temperatures have been investigated over the last decade as a means to simultaneously decrease engine-out particle and oxide of nitrogen (NO ) emissions. To overcome the trade-off between simultaneously low particle and NO emissions versus high "diesel-like" combustion efficiency, a new dual-fuel technique called Reactivity Controlled Compression Ignition (RCCI) has been researched. In the present study, particle size distributions were measured from RCCI for four gasoline:diesel compositions from 65%:35% to 84%:16%, respectively. Previously, fuel blending (reactivity control) had been carried out by a port fuel injection of the higher volatility fuel and a direct in-cylinder injection of the lower volatility fuel. With a recent mechanical upgrade, it was possible to perform injections of both fuels directly into the combustion chamber.

Compared to the gasoline engine, the diesel engine has the advantage of being more efficient and hence achieving a reduction of CO₂ levels. Unfortunately, particulate matter (PM) and nitrogen oxides (NOx) emissions from diesel engines are high. To overcome these drawbacks, several new combustion concepts have been developed, including the PCCI (Premixed Charge Compression Ignition) combustion mode. This strategy allows a simultaneous reduction of NOx and soot emissions through the reduction of local combustion temperatures and the enhancement of the fuel/air mixing. In spite of PCCI benefits, the concept is characterized by its high combustion noise levels. Currently, a promising way to improve the PCCI disadvantages is being investigated. It is related with the use of low cetane fuels such as gasoline and diesel-gasoline blends.

A fundamental study to experimentally analyze the effect of cavitation in common-rail diesel nozzles on the soot formation process was carried out. The soot content was characterized by measuring the soot radiation, and an original methodology was developed to suitably characterize the soot formation process from this soot content. After a significant effort to overcome the different difficulties when analyzing the experimental data, the results seem to show a promising conclusion: cavitation reduces the soot formation rate. This reduction is explained, on the one hand, because it leads to a reduction in the effective diameter, thus diminishing the equivalence fuel/air ratio at the lift-off length; and, on the other hand, because it provokes an increase in effective velocity, thus increasing the lift-off length and reducing the corresponding equivalence fuel/air ratio.