Refine Your Search

Date

Date

Automotive Heat treatment Finishing Fasteners Committee

Search Results

Viewing 1 to 20 of 84
123Next >Last >>
Sort by relevance
Standard

LOCK WASHERS
1974-02-01
HISTORICAL
J489B_197402
This SAE Standard covers the complete dimensional and general specifications, including physical properties and methods of testing, for those types of lock washers intended for use in automotive and general industrial applications.
Standard

Thread Rolling Screws
2012-07-05
CURRENT
J81_201207
This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) NOTE—The performance requirements covered in this document apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

Thread Rolling Screws
1997-09-01
HISTORICAL
J81_199709
This SAE Standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.)
Standard

THREAD ROLLING SCREWS
1972-07-01
HISTORICAL
J81_197207
This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that “thread rolling” screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

THREAD ROLLING SCREWS
1979-06-01
HISTORICAL
J81_197906
This standard covers requirements for thread rolling screws suitable for use in general engineering applications. (It is intended that "thread rolling" screws have performance capabilities beyond those normally expected of other standard types of tapping screws.) Note: The performance requirements covered in this standard apply only to the combination of laboratory conditions described in the testing procedures. If other conditions are encountered in an actual service application (such as different materials, thicknesses, hole sizes, etc.), values shown herein for drive torque, torque-to-clamp load, and proof torque may require adjustment.
Standard

Protective Coatings for Fasteners
2019-10-07
CURRENT
J1648_201910
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard

PROTECTIVE COATINGS FOR FASTENERS
1996-08-01
HISTORICAL
J1648_199608
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard

Protective Coatings for Fasteners
2013-04-15
HISTORICAL
J1648_201304
This SAE Information Report is provided as an advisory guide. Careful discretion as to application is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. It covers finishes applied to fasteners and related topics, corrosion resistance, lubricity, electrical grounding, ultraviolet light, and embrittlement. Table 1 lists these coatings and their properties so that finish selection can be reasonably made in accordance with known and anticipated fastener assembly applications. Application of protective coatings will affect fastener dimensions. This is especially critical for the thread fit of mating parts because the pitch diameter increases by four times the coating thickness. Explanation is covered in Section 5.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series
2019-08-07
CURRENT
J174_201908
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Inch Series
2013-04-11
HISTORICAL
J174_201304
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

TORQUE-TENSION TEST PROCEDURE FOR STEEL THREADED FASTENERS—INCH SERIES
1998-05-01
HISTORICAL
J174_199805
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 1/4 through 1 in nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the metric version, see SAE J174M.
Standard

TORQUE-TENSION TEST PROCEDURE FOR STEEL THREADED FASTENERS—METRIC SERIES
1998-05-01
HISTORICAL
J174M_199805
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

Torque-Tension Test Procedure for Steel Threaded Fasteners - Metric Series
2013-04-11
HISTORICAL
J174M_201304
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque-type threaded steel fasteners 6 through 24 mm nominal diameters. Realistically, torque-tension relationships for specific individual fastener assembly joints will vary due to the different joint parameters. Tests using actual joint components will be required to determine accurate torque-tension values for those conditions. For the inch series version, see SAE J174.
Standard

DECARBURIZATION IN HARDENED AND TEMPERED THREADED FASTENERS
1983-08-01
HISTORICAL
J121_198308
This recommended practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS
1996-08-01
HISTORICAL
J121M_199608
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
123Next >Last >>
X