Search Results

Studies have shown that premixed combustion concepts such as PCCI and RCCI can achieve high efficiencies while maintaining low NOx and soot emissions. The RCCI (Reactivity Controlled Compression Ignition) concept use blending port-injected high-octane fuel with early direct injected high-cetane fuel to control auto-ignition. This paper describes studies on RCCI combustion using CNG and diesel as the high-octane and high-cetane fuels, respectively. The test was conducted on a heavy-duty single cylinder engine. The influence of injection timing and duration of the diesel injections was examined at 9 bar BMEP and1200 rpm. In addition, experiments were conducted using two different compression ratios, (14 and 17) with different loads and engine speeds. Results show both low NOx and almost zero soot emissions can be achieved but at the expense of increasing of unburned hydrocarbon emissions which could potentially be removed by catalytic after-treatment.

The present competitive market scenario and customer requirements demand for improved NVH quality and to meet statutory norms without increased cost. When gears are used for power transmission, gear noise is of particular concern. The noise may be created due to harmonics of the rotating and meshing internal components. This has a significant effect on the overall vehicle sound quality. Various factors contribute to gearbox noise. Some of them include shaft misalignments, gear geometry, lubrication, bearings and loose mountings. Hence it is essential to study which factors contribute to the gearbox noise and to develop countermeasures for the same. Although a number of factors may contribute to gear noise as mentioned, the scope of this paper is limited to the effect of gear geometry alone on the gearbox noise.

To improve overall customer experience, it is imperative to minimize the noise levels inside agricultural equipment cab. Up-front prediction of acoustic performance in product development is critical to implement the noise control strategies optimally. This paper discusses the methodology used for virtual modeling of a cab on agricultural equipment for prediction of interior noise. The Statistical Energy Analysis (SEA) approach is suitable to predict high frequency interior noise and sound quality parameters such as articulation index and loudness. The cab SEA model is developed using a commercial software. The structural and acoustic excitations are measured through physical testing in various operating conditions. The interior noise levels predicted by the virtual model are compared with the operator ear noise levels measured in the test unit. The resultant SPL spectrum from SEA correlates well with the test.

Diffusive combustion of direct injected ethanol is investigated in a heavy-duty single cylinder engine for a broad range of operating conditions. Ethanol has a high potential as fossil fuel alternative, as it provides a better carbon footprint and has more sustainable production pathways. The introduction of ethanol as fuel for heavy-duty compression-ignition engines can contribute to decarbonize the transport sector within a short time frame. Given the resistance to autoignition of ethanol, the engine is equipped with two injectors mounted in the same combustion chamber, allowing the simultaneous and independent actuation of the main injection of pure ethanol and a pilot injection of diesel as an ignition source. The influence of the dual-fuel injection strategy on ethanol ignition, combustion characteristics, engine performance and NOx emissions is evaluated by varying the start of injection of both fuels and the ethanol-diesel ratio.

To overcome the trade-offs of thermal efficiency with energy loss and exhaust emissions typical of conventional diesel engines, a new diffusion-combustion-based concept with multiple fuel injectors has been developed. This engine employs neither low temperature combustion nor homogeneous charge compression ignition combustion. One injector was mounted vertically at the cylinder center like in a conventional direct injection diesel engine, and two additional injectors were slant-mounted at the piston cavity circumference. The sprays from the side injectors were directed along the swirl direction to prevent both spray interference and spray impingement on the cavity wall, while improving air utilization near the center of the cavity.

Gas engines (fuelled with CNG, LNG or Biogas) for generation of power and heat are, to this date, taking up larger shares of the market with respect to diesel engines. In order to meet the limit imposed by the TA-Luft regulations on stationary engines, lean combustion represents a viable solution for achieving lower emissions as well as efficiency levels comparable with diesel engines. Leaner mixtures however affect the combustion stability as the flame propagation velocity and consequently heat release rate are slowed down. As a strategy to deliver higher ignition energy, an active pre-chamber may be used. This work focuses on assessing the performance of a pre-chamber combustion configuration in a stationary heavy-duty engine for power generation, operating at different loads, air-to-fuel ratios and spark timings.

There is growing global interest in using renewable alcohols to reduce the greenhouse gases and the reliance on conventional fossil fuels. Recent studies show that methanol combined with partially premixed combustion provide clear performance and emission benefits compared to conventional diesel diffusion combustion. Nonetheless, high unburned hydrocarbon (HC) and carbon monoxide (CO) emissions can be stated as the main PPC drawback in light load condition when using high octane fuel such as Methanol with single injection strategy. Thus, the present experimental study has been carried out to investigate the influence of multiple injection strategies on the performance and emissions with methanol fuel in partially premixed combustion. Specifically, the main objective is to reduce HC, CO and simultaneously increase the gross indicated efficiency compared to single injection strategy.

The future of bus transit in new millennium is promising. This optimism is based on an anticipated long-term slowdown in growth of suburbs and revitalization of central cities. It reflects and escalates the public concern with traffic congestion, sprawl and pollution. This calls for double the use of public transport to address above issues. It calls for changing the mind-set of society towards public transports like buses, coaches etc. This could happen if bus design ensures right comfort, safety and TCO by ensuring refined bus transport. Hence, it is responsibility of OEMs to provide the new generation buses and coaches, which will ensure the public demands of comforts in terms of NVH refinement. This paper covers the unique approach used to convert the existing bus NVH refinement to next level as a short-term solution and with the intention of articulating NVH strategies for new generation bus development.

A truck and bus transportation which support logistics and people, diesel engines are highly expected to have high thermal efficiency and low exhaust emissions over the next few decades. Effective methods to achieve even higher thermal efficiency are to reduce a cooling loss from combustion chamber wall. A multi-hole diesel injector has a significant impact on improving engine thermal efficiency by enhancing a combustion activity and reducing a cooling loss. In this study, two types of diesel injectors - 8-hole and 14-hole - with the same flow rate were tested under heavy-duty diesel engine condition. Heat release rate, energy balance and engine emissions were investigated using the single-cylinder engine with displacement of 1,478 cc. Furthermore, an optical engine was used to observe quantitative spray penetration and flame development from shadowgraph imaging and analyze flame temperature by a two-color method.

Combustion characteristics of dimethyl ether, DME, have been investigated experimentally, in a heavy duty single cylinder engine equipped with an adapted common rail fuel injection system, and the effects of varying injection timing, rail pressure and exhaust gas recirculation on the combustion and emission parameters. The results show that DME combustion does not produce soot and with the use of exhaust gas recirculation NOX emissions can also be reduced to very low levels. However, high injection pressure and/or a DME adopted combustion system is required to improve the mixing process and thus reduce the combustion duration and carbon monoxide emissions.

A single cylinder engine was modified into a photographic test equipment. A new method-filling and cycling nitrogen gas to the cylinder-was used to keep the fuel in combustion chamber out of firing. Tests were carried out at three fuel injection pressure and three gas swirl rates. The chamber swirl rate was measured by hot-wire anemometer, the fuel spray pictures were taken by a high speed camera. By reference to the experimental results, the spray bevaviers in swiling flow were discussed both in the main injection and the end injection periods.

Light weighting vehicle acoustic components and improving the performance level of sound abatement treatments is becoming more important to automotive manufacturers due to increased fuel economy requirements established by the Corporate Average Fuel Economy - (CAFE) standards [1], and the consumer’s demand for ever improving sound quality inside the vehicle cabin. In tests conducted by Ricardo Inc. for the Aluminum Association Inc., a 2008 report estimates that for every 45 kg of mass removed from passenger vehicles and light weight commercial vehicles (LCV) up to a 1 percent increase in fuel mileage can be achieved [2]. Automotive OEM’s expect that sound abatement products, sound barriers, absorbers, and damping materials contribute to this reduction in vehicle weight.

Truck and construction seats offer a number of different challenges compared to automotive seats in the identification and characterization of Buzz, Squeak, and Rattle (BSR) noises. These seats typically have a separate air or mechanical suspension and usually a larger number and variety of mechanical adjustments and isolators. Associated vibration excitation tend to have lower frequencies with larger amplitudes. In order to test these seats for both BSR and vibration isolation a low-noise shaker with the ability to test to a minimum frequency of 1 Hz was employed. Slowly swept sine excitation was used to visualize the seat mode shapes and identify nonlinearities at low frequencies. A sample set of seat BSR sounds are described in terms of time and frequency characteristics, then analyzed using sound quality metrics.

Typical approaches to regulating sound performance of vehicles and products rely upon A-weighted sound pressure level or sound power level. It is well known that these parameters do not provide a complete picture of the customer’s perception of the product and may mislead engineering efforts for product improvement. A leading manufacturer of agricultural equipment set out to implement a process to include sound quality targets in its product engineering cycle. First, meaningful vehicle level targets were set for a tractor by conducting extensive jury evaluation testing and by using objective metrics that represent the customer’s subjective preference for sound. Sensitivity studies (“what-if” games) were then conducted, using the predicted sound quality (SQ) index as validation metric, to define the impact on the SQ performance of different noise components (frequency ranges, tones, transients).

An ongoing research and development activities on the scavenged pre-chamber ignition system for an automotive natural gas fueled engine is presented in this paper. The experimental works have been performed in engine laboratory at steady state conditions on a gas engine with 102 mm bore and 120 mm stroke, converted to a single cylinder engine. The in-house designed scavenged pre-chamber is equipped with a spark plug, fuel supply and a miniature pressure sensor for detailed combustion diagnostics. The engine was operated at constant speed, fully open throttle valve and four different fueling modes with or without spark discharge. A partly motored mode allowed direct evaluation of the pre-chamber heat release. The experimental data acquired in this research served as a validation data for the numerical simulations. The performed tests of prototypes and calculations have recently been expanded to include 3-D flow calculations in the Ansys Fluent software.

The increased availability of natural gas (NG) in the United States (US) and its relatively low cost versus diesel fuel has increased interest in the conversion of medium duty (MD) and heavy duty (HD) engines to NG fueled combustion systems. The aim for development for these NG engines is to realize fuel cost savings and increase operating range while reduce harmful emissions and maintaining durability. Traditionally, port-fuel injection (PFI) or premixed NG spark-ignited (SI) combustion systems have been used for light duty LD, and MD engines with widespread use in the US and Europe [1]. However, this technology exhibits poor thermal efficiency and is load limited due to knock phenomenon that has prohibited its use for HD engines. Spark Ignited Direct Injection (SIDI) can be used to create a partially stratified combustion (PSC) mixture of NG and air during the compression stroke.

The diesel engine is still one of the most common and most efficient mobile energy converters. Nevertheless, it is troubled by many problems, one of them being nozzle coking. This is not a new problem; however, due to the introduction of more advanced injection systems and a more diverse fuel matrix, including biofuels, the problem has become more complex. The nozzle holes are also much narrower today than when the problem first appeared and are therefore more sensitive to coking. Two CEC sanctioned coking tests exist for diesel engines, but no universally accepted test for heavy duty engines. In this paper, tests have been performed with B10 doped with 1 ppm zinc on a single cylinder engine, based on a heavy duty engine, with the purpose to develop a simple accelerated coking test. To have relevance to real usage, the test was based on real engine load points from a high power Euro V engine calibration. The coking propensity was studied in an engine speed sweep at max load.

Increased customer expectation for NVH refinement creates a significant challenge for the integration of Diesel powertrains into passenger vehicles that might have been initially developed for gasoline engine applications. A significant factor in the refinement of Diesel powertrain sound quality is calibration optimization for NVH, which is often constrained by performance, emissions and fuel economy requirements. Vehicle level enablers add cost and weight to the vehicle and are generally bounded by vehicle architecture, particularly when dealing with a carry-over vehicle platform, as is often the case for many vehicle programs. These constraints are compounded by the need to make program critical sound package content decisions well before the availability of prototype vehicles with the right powertrain. In this paper, a case study on NVH development for integration of a light duty Diesel powertrain is presented.

NVH is very important topic in development of a vehicle. Legislative requirements for driver ear level, the comparison to competitor vehicles in terms of noise and vibration as well as sound quality set very challenging targets. High noise at Driver Ear Level (DEL) and tactile vibrations of tractor is the major cause of exhaustion to the operator. With growing competition there is need for the tractor manufacturers to control noise and vibration levels. Recognizing the corrective measures to reduce the noise and vibration has a greater impact in increasing the efficiency of the product and operator comfort. Objective of this paper is to control vehicle level noise and vibrations using vehicle level structure modifications. It includes airborne and structure borne NVH study on a tractor by measuring sound pressure and vibration levels at vehicle level. Single cylinder engine was mounted on light weight structure to meet the power and torque requirements in the tractor.