Refine Your Search

Date

Date

Topic

Topic

Author

Author

Standard Drag Tools and equipment Suppliers Exterior lighting Casting Commercial Vehicle Cleaning

Search Results

Viewing 1 to 20 of 363
123Next >Last >>
Sort by relevance
Standard

Combination Tail and Floodlamp for Industrial Equipment
2003-05-15
CURRENT
J94_200305
This SAE Standard provides performance and general design requirements and related test procedures for a combination tail and floodlamp for use on industrial wheeled equipment that may be operated on public roads.
Standard

Tire Size Differential - Articulated Wheel Loader
2019-11-20
CURRENT
J2204_201911
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
Standard

TIRE SIZE DIFFERENTIAL—ARTICULATED WHEEL LOADER
1994-05-01
HISTORICAL
J2204_199405
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
Standard

Torque Ratings for Power Take-off Mounting Pads
2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Measurement of Aerodynamic Performance for Mass-Produced Cars and Light-Duty Trucks
2010-06-03
HISTORICAL
J2881_201006
This recommended practice provides a procedure for measuring and documenting the aerodynamic performance in a full-scale wind tunnel of passenger vehicles, i.e., mass-produced cars and light-duty trucks intended primarily for individual consumers. Testing or numerical modeling of pre-production and/or reduced-scale models is outside the scope of this document. Aerodynamic development procedures, i.e., methods to improve or optimize aerodynamic performance, are also excluded. It is well-known that aerodynamic performance results depend significantly on vehicle content and loading, as well as the wind tunnel itself (type, scale, and simulation qualities of the wind tunnel). Publication of non-standard test results causes unnecessary additional development work and incorrect perception of a vehicle’s anticipated aerodynamic performance by government, academia, and the general public.
Standard

Truck and Bus Aerodynamic Device and Concept Terminology
2019-08-02
CURRENT
J2971_201908
This SAE J2971 Recommended Practice describes a standard naming convention of aerodynamic devices and technologies used to control aerodynamic forces on truck and buses weighing more than 10000 pounds (including trailers).
Standard

Truck and Bus Aerodynamic Device and Concept Terminology
2013-04-09
HISTORICAL
J2971_201304
This SAE J2971 Recommended Practice Truck and Bus Aerodynamic Device Terminology document describes a standard naming convention of aerodynamic devices and technologies used to control aerodynamic forces on truck and buses weighing more than 10,000 pounds (including trailers).
Standard

Recreation Off-Road Vehicle Product Identification Numbering System
2012-05-07
CURRENT
ICS1000_201205
This document specifies the format, content and parameters for a product identification numbering system for off-road recreation vehicles, based on the PIN structure for earth-moving machinery in ISO 10261:2002E and is not applicable to the identification of components or attachments. This standard applies only to the off-road recreation vehicle industry and does not impose parameters for the marine, lawn and garden, silviculture, husbandry, construction or earth moving sectors.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply
2020-02-25
CURRENT
J2691_202002
This SAE Standard establishes the minimum construction and performance requirements for a 15 pole connector between towing vehicles and trailers, for trucks, trailers, and dollies, for 12 VDC nominal applications in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply
2018-04-15
HISTORICAL
J2691_201804
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

LED Work Lighting Devices
2022-06-13
CURRENT
J2895_202206
This SAE Recommended Practice provides general design performance requirements and related test procedures for LED “white” lighting unit assemblies, other than signal and marking devices, used on Earthmoving, Road Building, and Maintenance off-road work machines as defined in SAE J1116. This report is intended to serve as a guide to standard practice and is subject to change to reflect additional experience and technical advances.
Standard

RECOMMENDATIONS FOR CHILDREN’S SNOWMOBILE
1975-12-01
HISTORICAL
J1038_197512
This recommended practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children’s snowmobile as identified in Section 1.3.
Standard

RECOMMENDATIONS FOR CHILDREN’S SNOWMOBILE
1980-02-01
HISTORICAL
J1038_198002
This recommended practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children’s snowmobile as identified in Section 1.3.
Standard

RECOMMENDATIONS FOR CHILDREN'S SNOWMOBILE
1984-10-01
HISTORICAL
J1038_198410
This recommended practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children's snowmobile as identified in paragraph 1.3.
123Next >Last >>
X