Search Results

Standard

SAE J1939 Network Security

2017-03-06

WIP

J1939-91

This document will provide recommendations to vehicle manufacturers and component suppliers in securing the SAE J1939-13 connector interface from the cybersecurity risks posed by the existence of this connector.

Standard

Performance Requirements for Nonmetallic Air Brake System Tubing

2014-08-26

WIP

J2547

This SAE Standard covers the minimum requirements for nonmetallic tubing as manufactured for use in air brake systems which tubing is different from that described in SAE J844. It is not intended to cover tubing for any portion of the system which operates continuously below - 40 degrees C or above +93 degrees C, above a maximum working gage pressure of 1.0 MPa, or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections, which maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this document, SAE J1131 and SAE J2494-3, to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections which are used in the construction of such assemblies.

Standard

Constant Speed Aerodynamic Procedure for Heavy Vehicles

2017-09-25

WIP

J3156

Develop and document an aerodynamic constant speed procedure for heavy vehicles that can accurately calculate the aerodynamic performance through the typical expected yaw angles during operation at highway speeds.

Standard

Taxonomy and Definitions for Automated Multi-Vehicle Truck and Bus Systems

2017-07-10

WIP

J3150

Scope: This document provides a taxonomy and definitions for trucks and buses with GVWR of more than 10,000 pounds with driving automation systems that perform part or all of the dynamic driving task on a sustained basis and that range in level from no driving automation (level 0) to full driving automation (level 5).

Standard

Tire Size Differential - Articulated Wheel Loader

2019-11-20

CURRENT

J2204_201911

This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.

Standard

TIRE SIZE DIFFERENTIAL—ARTICULATED WHEEL LOADER

1994-05-01

HISTORICAL

J2204_199405

This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.

Standard

Fasteners - Part Standard - Cap Screws, Hex Bolts, and Hex Nuts (Metric)

2019-05-10

CURRENT

J2295M_201905

This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.

Standard

Fasteners—Part Standard—Cap Screws, Hex Bolts, and Hex Nuts (Metric)

2006-06-21

HISTORICAL

J2295M_200606

This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.

Standard

SHIP SYSTEMS AND EQUIPMENT—FASTENERS—SELECTION AND IDENTIFICATION REQUIREMENTS

1996-04-01

HISTORICAL

J2280_199604

This SAE Standard provides a comprehensive list of requirements for the selection, identification, and control of metric and inch sized fasteners for use in shipboard applications for both shipbuilder installed joints and for use in shipboard components. The fastener selection requirements include the following: a Materials b Thread selection c Plating, coatings, and surface treatments d Locking devices and elements e Screw thread fastener inserts f Fastener part or identifying numbers g Identification markings

Standard

Clutch Dimensions for Truck and Bus Applications

2017-08-14

CURRENT

J1806_201708

Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).

Standard

Clutch Dimensions for Truck and Bus Applications

1999-11-30

HISTORICAL

J1806_199911

Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).

Standard

Drain and Fill Plug for use on Engines, Transmissions, and Axles

2003-07-29

HISTORICAL

J2606_200307

Drain and Fill plugs used on engines, transmissions, transfer cases and front and rear drive axles for class 5 – 8 vehicles.

Standard

Drain and Fill Plug for use on Engines, Transmissions, and Axles

2017-09-19

CURRENT

J2606_201709

Drain and Fill plugs used on engines, transmissions, transfer cases and front and rear drive axles for class 5 – 8 vehicles.

Standard

General Environmental Considerations for Marine Vehicles

2014-02-04

WIP

J1777

This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.

Standard

GENERAL ENVIRONMENTAL CONSIDERATIONS FOR MARINE VEHICLES

1990-12-01

CURRENT

J1777_199012

This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably.

Standard

Test Method to Obtain Lug-Up Torque Data for Heavy-Duty Truck and Bus Engines

2001-04-25

CURRENT

J2548_200104

This SAE Recommended Practice applies to all forms of diesel and natural gas engines fueled by the combination of diesel fuel and natural gas.

Standard

Torque Ratings for Power Take-off Mounting Pads

2017-09-19

CURRENT

J2662_201709

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

Standard

Torque Ratings for Power Take-off Mounting Pads

2003-07-25

HISTORICAL

J2662_200307

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

Standard

Coiled Tubing Assemblies for Heavy Duty Air Brake Applications

2022-06-03

WIP

J3041

This SAE Standard establishes the minimum performance and endurance requirements for coiled air brake tubing assemblies used for hookup between tractors, trailers and converter dollies. The Standards SAE J844 and SAE J246 along with J1131 must be consulted to determine the complete performance and endurance requirements of individual components of the system. Related TMC Recommended Practices may be consulted for information associated with selection, installation and inspection of these assemblies. This document is intended to set out requirements for the majority of conditions rather than for specialized applications or environments.

Standard

Air Disc Brake Actuator Test Procedure, Truck-Tractor, Bus and Trailer

2020-12-07

CURRENT

J2902_202012

This SAE recommended practice provides procedures and methods for testing service, spring applied parking and combination brake actuators for air disc brake applications. Methods and recommended samples for testing durability, function and environmental performance are listed in 1.1 and 1.2.