Refine Your Search

Date

Date

Topic

Topic

Author

Author

Cleaning Tools and equipment Materials Suppliers Drag Standard Manufacturing equipment and machinery Commercial Vehicle Casting

Search Results

Viewing 1 to 20 of 597
123Next >Last >>
Sort by relevance
Standard

Tire Size Differential - Articulated Wheel Loader
2019-11-20
CURRENT
J2204_201911
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
Standard

TIRE SIZE DIFFERENTIAL—ARTICULATED WHEEL LOADER
1994-05-01
HISTORICAL
J2204_199405
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
Standard

Fasteners - Part Standard - Cap Screws, Hex Bolts, and Hex Nuts (Metric)
2019-05-10
CURRENT
J2295M_201905
This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.
Standard

Fasteners—Part Standard—Cap Screws, Hex Bolts, and Hex Nuts (Metric)
2006-06-21
HISTORICAL
J2295M_200606
This SAE Part Standard covers selected metric screws, hex bolts, and nuts manufactured in accordance with American Society for Testing and Materials (ASTM) and SAE fastener standards. This document covers fastener materials often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This document permits the fasteners to be identified and ordered by a part or identifying number (PIN) as defined in this document.
Standard

SHIP SYSTEMS AND EQUIPMENT—FASTENERS—SELECTION AND IDENTIFICATION REQUIREMENTS
1996-04-01
HISTORICAL
J2280_199604
This SAE Standard provides a comprehensive list of requirements for the selection, identification, and control of metric and inch sized fasteners for use in shipboard applications for both shipbuilder installed joints and for use in shipboard components. The fastener selection requirements include the following: a Materials b Thread selection c Plating, coatings, and surface treatments d Locking devices and elements e Screw thread fastener inserts f Fastener part or identifying numbers g Identification markings
Standard

General Environmental Considerations for Marine Vehicles
2014-02-04
WIP
J1777
This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.
Standard

GENERAL ENVIRONMENTAL CONSIDERATIONS FOR MARINE VEHICLES
1990-12-01
CURRENT
J1777_199012
This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably.
Standard

Torque Ratings for Power Take-off Mounting Pads
2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
Standard

Measurement of Aerodynamic Performance for Mass-Produced Cars and Light-Duty Trucks
2010-06-03
HISTORICAL
J2881_201006
This recommended practice provides a procedure for measuring and documenting the aerodynamic performance in a full-scale wind tunnel of passenger vehicles, i.e., mass-produced cars and light-duty trucks intended primarily for individual consumers. Testing or numerical modeling of pre-production and/or reduced-scale models is outside the scope of this document. Aerodynamic development procedures, i.e., methods to improve or optimize aerodynamic performance, are also excluded. It is well-known that aerodynamic performance results depend significantly on vehicle content and loading, as well as the wind tunnel itself (type, scale, and simulation qualities of the wind tunnel). Publication of non-standard test results causes unnecessary additional development work and incorrect perception of a vehicle’s anticipated aerodynamic performance by government, academia, and the general public.
Standard

Truck and Bus Aerodynamic Device and Concept Terminology
2019-08-02
CURRENT
J2971_201908
This SAE J2971 Recommended Practice describes a standard naming convention of aerodynamic devices and technologies used to control aerodynamic forces on truck and buses weighing more than 10000 pounds (including trailers).
Standard

Truck and Bus Aerodynamic Device and Concept Terminology
2013-04-09
HISTORICAL
J2971_201304
This SAE J2971 Recommended Practice Truck and Bus Aerodynamic Device Terminology document describes a standard naming convention of aerodynamic devices and technologies used to control aerodynamic forces on truck and buses weighing more than 10,000 pounds (including trailers).
Standard

Discriminating Back-Up Alarm System Standard
2008-12-04
WIP
J1741
This SAE Standard describes methods for evaluating the performance of the systems detection device, the minimum detection areas behind the machine, the visual and audible information presented to the operator and ground personnel, and the systems fault detection requirements. Also included are operator system function tests and maintenance procedures. The purpose of this document is to establish performance requirements for a Discriminating Back-Up Alarm System.
Standard

MINIMUM PERFORMANCE CRITERIA FOR BRAKING SYSTEMS FOR SELF-PROPELLED, SMOOTH STEEL WHEEL, PNEUMATIC TIRED OR MULTIPLE PROJECTION STEEL WHEEL ROLLERS AND COMPACTORS
1976-04-01
HISTORICAL
J1136_197604
Minimum performance criteria for service braking systems, emergency stopping systems, and parking systems for all self-propelled vibratory and static weight smooth steel wheel, pneumatic tired or multiple projection steel wheel rollers and compactors are provided in this S.A.E. recommended practice.
123Next >Last >>
X