Search Results

This paper discusses the development of an all speed governed diesel-natural gas dual fuel engine for agricultural farm tractor. A 45 hp, 2.9 liters diesel-natural gas dual fuel engine with a novel closed loop secondary fuel injection system was developed. A frugal approach without any modification of the base mechanical diesel fuel injection system was followed. This approach helped to minimize the cost impact, while meeting performance and emissions at par with neat diesel operation. Additional cost on gas injection system is redeemed by cost savings on diesel fuel. The dual fuel technology developed by Mahindra & Mahindra Ltd., substitutes on an average approximately 40% of diesel with compressed natural gas, meeting the TREM III A emission norms for dual fuel while meeting all application requirements. The governing performance of the tractor was found to be superior than base diesel tractor.

Rotavator is an active tillage implement for breaking the Soil and for the preparation of seed bed for cultivation. The Farmers are currently facing problem due to usage of sub optimal speed of Rotavator which results in more fuel consumption, takes more time for completion of operation. Also, the Current Rental models work on Tractor + Implement as rental combination and customer not able to rent Rotavator as a standalone implement due to non-availability of Tracking information such as hours of utilization on Rotavator. Farmers not able to maintain the service periodicity, if oil change not done in prescribed duration then it may result in improper maintenance and breakdown of the Rotavator. To overcome these problems a smart Rotavator developed consists of an electronic unit fitted on the Rotavator shaft to measure the speed of the shaft rotation and in turn convert to Rotavator speed and also able to convert into Hours of usage based on the starting and stopping of the rotavator.

The given paper presents the main elements of frictional power loss distribution in an automotive axle for passenger car. For reference two different axles were compared of two different sizes to understand the impact of size and ratio of gear and bearings on power loss characteristics. It was observed that ~50% of total axle power loss is because of pinion head-tail bearing and its seals, which is very significant. Roughly 30% of total power loss is contributed by pinion-ring gear pair and differential bearings and remaining ~20% by wheel end bearing and seals. With this study the automotive companies can take note of the area where they need to focus more to reduce their CO2 emissions to meet the stringent BS6, CAFÉ and RDE emission norms.

Till recently supercharging was the most accepted technique for boost solution in gasoline engines. Recent advents in turbochargers introduced turbocharging technology into gasoline engines. Turbocharging of gasoline engines has helped in powertrains with higher power density and less overall weight. Along with the advantages in performance, new challenges arise, both in terms of thermal management as well as overall acoustic performance of powertrains. The study focuses mainly on NVH aspects of turbocharging of gasoline engines. Compressor surge is a most common phenomenon in turbochargers. As the operating point on the compressor map moves closer to the surge line, the compressor starts to generate noise. The amplitude and frequency of the noise depends on the proximity of the operating point to the surge line. The severity of noise can be reduced by selecting a turbocharger with enough compressor surge margin.

Battery Electric Vehicles (BEVs) are gaining momentum all around the world and India is not far behind in terms of EV sales. The principle difference between BEVs and Internal Combustion Engine based Vehicles (hereafter known as ICEs) is that BEVs run on electric motors and don’t have Internal Combustion based engines that generate significant noise while running. The engine noise contributes to noise pollution, but it is useful in alerting the pedestrians about the incoming vehicle and can function as a passive safety system. The lack of such noise can be a safety threat to pedestrians, cyclists, wildlife etc. Many countries around the world have mandated, or are in the process of mandating, a pass-by noise generating system to alert pedestrians about the incoming vehicle. This paper is an attempt to study various pass-by noise generating systems used worldwide in electric four-wheelers.

In automotive Transmission especially in Manual shift Transmission, a mechanism is provided for smooth and quick shifting of gears known as Synchronizer. A synchronizer mechanism having a Sliding shift sleeve, synchronizer ring, clutch body and clutch body ring as the main components to shift the gears smoothly. A synchronizer ring and Clutch body ring having outer tooth with inclined faces i.e. chamfer on their end facing towards gear shift sleeve, having inclination faces to mesh with the same inclined faces of blocker ring and clutch body ring for smooth shifting with less effort. Generally in cold environment certain forces are acting inside the Transmission to reduce the speed of rotating elements, these force are called drag forces. Mostly these drag force are generated due to high viscosity of transmission oil and large Inertia of masses of rotating elements, bearings and oil seals friction etc..

This paper details the methodology used to show the importance of Low rolling resistance tires in Electric Vehicles. Fuel efficiency and range is paramount with most of the electric vehicle buyers. Although many people are now becoming aware of low rolling resistance tires but its development started way back in 1990’s. It is always challenging to achieve low rolling resistance in smaller tires of size 12 inch or 13 inch along meeting the other critical vehicle parameters such as ride and handling, NVH, durability and many more. The reduction in rolling resistance can also affect the traction properties of tires. In case of very low rolling resistance tires the traction will be very less but it can badly affect the other vehicle parameters. Selection of tires further depend upon the RWUP (Real World Usage Profile). It means the vehicle is targeted for which region and what is the condition of roads there.

Plenum is the part located between the front windshield and the bonnet of an automobile . It is primarily used as an air inlet to the HVAC during fresh air mode operation. It’s secondary functions include water drainage, aesthetic cover to hide the gap between windshield to bonnet, concealing wiper motors and mechanisms etc. The plenum consists mainly two sub parts viz. upper plenum and lower plenum. Conventional plenum design which is found in majority of global OEMs employ a plastic upper plenum and a metal lower plenum which spans across the entire width of engine compartment. This conventional lower plenum is bulky, consumes more packaging space and has more weight. In this paper, we propose a novel design for the plenum lower to overcome above mentioned limitations of the conventional design. This novel design employs a dry and wet box concept for its working and is made up of complete plastic material.

Power density (power/engine cubic capacity) of the latest passenger car Diesel and Gasoline engine keeps increasing with a focus to deliver best in class performance along with meeting CAFE and emission norms. This increase in power density increases the thermal load onto the coolant system. Coolant temperature sensor monitoring the coolant temperature, proper radiator sizing, optimum water pump flow capacity and thermostat tuned to the required coolant temperature range are the typical measures taken to ensure safe operation of the engine and avoid any over-heating. Typical cooling system failures are mostly due to low coolant level, a defective thermostat, non-operative water pump & fan and blockage in the coolant circuit, etc. Most of these failures can be detected with the help of a coolant temperature sensor and pre-emptive measures can be taken to avoid engine loss.

The purpose of a differential is to allow the wheels of an automobile to turn at different speeds so that it does not skid during turning. However when a vehicle runs on a slick or muddy surface (especially in Agricultural and constructional Field applications) that same feature causes the wheel with less traction to spin freely as this unit transmits power to the tire with least amount of traction. The function of a difflock is to lock the differential gears, by locking the differential, both the axles receive equal power and hence equal traction is available at both the tires. This Paper describes the positive locking of a differential by stopper, and also in detail the problems associated with its engagement and disengagement in tractors and construction equipment's. Additionally a concept for a difflock stopper which has been experimentally proven for tractors and construction equipment's is also discussed.

An inadequate sealing of the combustion chamber gasket interface may have severe consequences on both the performance & emission of an engine. In this investigation, both the distribution of the contact pressure on the gasket and the stresses of the cylinder head at different loading conditions are explored and improved by modifying the design. A single cylinder gasoline engine cylinder head assembly has been analyzed by means of an uncoupled FEM simulation to find the sealing pressure of the multi-layer steel (MLS) gasket, strength & deformation of the components involved. The thermal loads are computed separately from CFD simulations of cylinder head assembly. The cylinder head assembly consisting of head, blocks, liner, cam shaft holder, bolts, gaskets, valve guides & valve seats, is one of the most complicated sub-assembly of an IC engine.

This paper describes vinyl ester based SMC (Sheet molding composite) material for oil sump part in automotive application. This sheet moulding composite is a ready to mould glass-fibre reinforced vinyl ester material primarily used in compression moulding process. This vinyl ester resin is compounded with glass fibre to meet the product functional requirements. Oil sump is a structural component under bonnet that forms the bottommost part of the crankcase and also contain the engine oil before and after it has been circulated through the engine. Generally, metals are preferred material for this application. In this paper, fibre filled vinyl ester based thermoset resin (SMC) material has been explored for oil sump application. They possess excellent properties in terms of tensile strength, modulus, impact strength, dimensional stability, high/low temperature resistance and oil resistance.

The Indian automotive industry has migrated from BS IV (Bharat stage IV) to BS VI (Bharat Stage VI) emission norms from 1st April 2020. This two-step migration of the emission regulations from BS IV to BS VI demands significant engineering efforts to design and integrate highly complex exhaust after-treatment system (EATS). In the present work, the methodology used to evaluate the EATS of a high power-density 1.5-liter diesel engine is discussed in detail. The EATS assembly of the engine consists of a diesel oxidation catalyst (DOC), a diesel particulate filter with selective catalytic reduction coating (sDPF), urea dosing module and urea mixer. Typically, all these components that are needed for emission control are integrated into a single canning of shell thickness ~1.5mm. Moreover, the complete EATS is directly mounted onto the engine with suitable mounting brackets on the cylinder block and cylinder head.

This paper describes the suitability of recycled polyethylene terephthalate (RPET) material for canopy strip in a commercial vehicle. The material described in this paper is a PET compound recycled from used PET bottles and reinforced with glass fibers so as to meet the product's functional requirements. The application described in this paper is a Canopy strip which is a structural exterior plastic part. Canopy strip acts as a structural frame to hold the Vinyl canopy in both sides of the vehicle. Functionally, the part demands a material with adequate mechanical and thermal properties. Generally, PET bottles are thrown after use thereby creating land pollution. PET being inert takes an extremely long time to degrade thereby occupying huge amount of space in landfills and directly affecting rain water percolation. This work focused on recycling the PET bottles and compounding them suitably so as convert them into useful automotive parts.

In recent times, Battery electric vehicles (BEV) have gained a lot of popularity since they can contribute immensely to control the urban air pollution. However, to consider the BEVs as a sustainable mobility solution, a significant improvement is needed in several aspects including performance, range, cost, weight and recharging time. In the present work, the acceleration performance of an electric vehicle is improved to match with its diesel variant by optimizing the accelerator pedal map strategy. Due to weight and cost constraints, the battery and electric machine capacity of the electric variant of the vehicle was considerably lower (41 % lesser power and 44% lesser torque). However, the expectation from the customers is to have no noticeable difference in the low-end performance feel between the variants.

Aeroacoustics of vehicles is becoming an important design criterion as it directly affects passenger’s comfort. The wind noise at highway speeds (>80 KMPH) is a critical quality concern under normal and crosswind conditions and dominant factor in assessing acoustic comfort of the vehicle. Wind noise is caused by the vortex air flow around a vehicle body and air leakage through the sealing gaps of attached parts. This majorly contributes to high frequency noise (>250 Hz). Accurate identification and control of noise sources and leakage paths result in improved acoustic comfort of the vehicle. In this paper, aero-acoustic quality characteristics of validation prototype vehicle are studied. The major wind noise sources and leakage paths in the vehicle are identified through in-house blower set up in the semi anechoic room. The overall wind noise level and articulation index of vehicle at various speeds are determined through on- road measurements.

Vehicle frame evaluation at early stages of product development cycle is essential to reduce product turnaround time to market. In conventional approach of virtual validation it is required to evaluate the strength of the vehicle structure to account for the standard Service Load Analysis (SLA) loading conditions. But this paper describes on the strength analysis of scooter frame with derivation of critical static load cases. The critical load cases are extracted from the load-time history while the vehicle was simulated on durability virtual test rigs which is equivalent to proving ground tests. This methodology gives the better accuracy in prediction of stress levels and avoids the overdesign of components based on traditional validation technique. There is significant drop in stress levels using the critical load case approach as compared to conventional load case method.

Phosphating is the most preferred surface treatment process used for auto body sheet panel before painting due to its low-cost, easy production process, good corrosion resistance, and excellent adhesion with subsequent paint layer. There are different phosphating processes used for ferrous metal like zinc phosphating, iron phosphating, di-cationic & tri-cationic phosphating, etc. Among these phosphate coatings, the best corrosion resistance and surface adhesion are achieved by tri-cationic phosphate coatings (zinc-nickel-manganese phosphate). Many new technologies of phosphating are evolving. Key drivers for this evolution are increasing demand for higher corrosion resistance, multi-metal car body processing in same phosphating bath and sustainability initiatives to reduce the carbon footprints. We have evaluated two of these recent technologies.

With increase in demand for quieter product and reduction in masking noise, axle whine management plays a crucial role in the early product development process. Whine is tonal in nature and humans are more sensitive to tonal memory, hence this makes user to experience a very unpleasant ride which in turn results in bad product credibility. Dynamic mesh force excitation is the cause of the axle whine noise. Critical factors in consideration are gear micro geometry variability, misalignments, temperature of operation and resulting bearing pre-load, operating loads, and structural resonances that carry the excitation to the occupant’s ear. The variability associated with gear micro-geometry plays crucial role during optimization in the quest for robust gear design.

The fuel economy of the internal combustion engine becomes progressively critical, especially with the stringent standards set by the government. To meet the government norms such as CAFE (Corporate Fuel Average Economy), different technologies are being explored and implemented in internal combustion engines. Several technologies such as variable oil pump, map controlled PCJ (Piston Cooling Jet), variable or switchable water pump & ball bearing turbocharger etc. This study investigates the effectiveness of implementing map-controlled PCJ implemented for a 1.5-litre 3-cylinder diesel engine. PCJ’s are major consumers of oil flow and map-controlled PCJ is used by many OEM’s e.g., Ford EcoSport to reduce the oil pump flow. In map-controlled PCJ, the oil to the PCJ is controlled using a solenoid valve. The solenoid valve can be completely variable or ON/OFF type. In our application, the ON/OFF type solenoid value is used to regulate the oil flow to PCJ.