Refine Your Search

Date

Date

Topic

Topic

Risk assessments Suppliers Analysis methodologies Body structures Standardization MTC1, Earthmoving Machinery

Search Results

Viewing 1 to 20 of 28
12Next >Last >>
Sort by relevance
Standard

Hole Placement on Dozer End Bits
1998-05-01
CURRENT
J63_199806
The recommended practice applies to straight blade, angling blade, U blade, and semi-U blades used on earthmoving tractors per SAE J1057a up to a maximum weight of 100,000 lb (45,000 kg).
Standard

Nomenclature - Hydraulic Backhoes
2018-11-20
HISTORICAL
J326_201811
This SAE standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.
Standard

Nomenclature - Hydraulic Backhoes
2012-11-01
HISTORICAL
J326_201211
This SAE Standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing, and are mounted on wheel tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.
Standard

CAPACITY RATING—ELEVATING SCRAPERS
1993-06-01
HISTORICAL
J957_199306
This SAE Standard specifies a procedure for approximating the volume of a typical material carried in the bowl of an elevating scraper as defined in SAE J728 and SAE J1057. The volumes are based on the inside dimensions of the bowl and a representative volume on top of the bowl. This rating method is intended to provide a consistent means of comparing capacities; it is not intended to define actual capacities that might be observed in any specific application.
Standard

IDENTIFICATION TERMINOLOGY—PIPELAYERS
1980-06-01
HISTORICAL
J1295_198006
This standard applies to machines which are designed to raise, lower, and carry pipe and loads of similar nature. The term pipelayer does not include tractors or loaders with side booms which are optional attachments, manufacturer or dealer-installed, to machines as defined in SAE J1057. Note: Some related standards will apply equally to pipelayers and to tractors and loaders with side boom. Two such standards are SAE J743 and ANSI B30.14.
Standard

Travel Performance and Rating Procedure, Crawler Mounted Hydraulic Excavators, Material Handlers, Knuckle Boom Log Loaders, and Certain Forestry Equipment
2012-01-06
CURRENT
J1309_201201
This SAE Standard describes a uniform method to calculate and specify travel performance characteristics of hydraulic excavators, material handlers, knuckle boom log loaders, delimbers, feller bunchers, harvesters, processors, and other knuckle boom material handlers. It establishes definitions and specifies machine conditions for calculations and tests. This document applies to crawler mounted machines such as hydraulic excavators as defined in SAE J/ISO 6165 and ISO 7135, and knuckle boom log loaders as defined in SAE J1209 and SAE J2055. This document also applies to certain forestry equipment defined in SAE J1209 and ISO 6814 that have crawler mountings such as delimbers, feller bunchers, harvesters, and processors. Included in the definition of hydraulic excavators are also front shovel, clamshell, and telescoping boom excavators.
Standard

Loading Ability Test Procedure - Scrapers
2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

CUTTING EDGE - CROSS SECTIONS LOADER STRAIGHT
1985-02-01
HISTORICAL
J1303_198502
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.
Standard

Cutting Edge—Cross Sections Loader Straight
2006-02-05
HISTORICAL
J1303_200602
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.
Standard

CUTTING EDGE—CROSS SECTIONS LOADER STRAIGHT WITH BOLT HOLES
1985-02-01
HISTORICAL
J1304_198502
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters.
Standard

Cutting Edge - Cross Sections Loader Straight
2011-10-25
CURRENT
J1303_201110
For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85. NOTE—For some heavy duty applications, cross sections with larger blunts and greater bevel angles may be required.
12Next >Last >>
X