Search Results

A semi-empirical index to evaluate the noise propensity of brake friction materials is introduced. The noise propensity index (NPI) is based on the ratio of surface and matrix stiffness of the friction material, fraction of high-pressure contact plateaus on the sliding surface, and standard deviation of the surface stiffness of the friction material that affect the amplitude and frequency of the stick-slip oscillation. The correlation between noise occurrence and NPI was examined using various brake linings for commercial vehicles. The results obtained from reduced-scale noise dynamometer and vehicle tests indicated that NPI is well correlated with noise propensity. The analysis of the stick-slip profiles also indicated that the surface property affects the amplitude of friction oscillation, while the mechanical property of the friction material influences the propagation of friction oscillation after the onset of vibration.

Copper has been regarded as one of the indispensable ingredients in the brake friction materials since it provides high thermal diffusivity at the sliding interface. However, the recent regulations against environmentally hazardous ingredients limit the use of copper in the commercial friction material and much effort has been made for the alternatives. In this work, the role of the cuprous ingredients such as copper fiber, copper powder, cupric oxide (CuO), and copper sulfide (CuS) are studied using the friction materials based on commercial formulations. The investigation was performed using a full inertial brake dynamometer and 1/5 scale dynamometer for brake performance and wear test. Results showed that the cuprous ingredients played a crucial role in maintaining the stable friction film at the friction interface, resulting in improved friction stability and reduced aggressiveness against counter disk.

Suspension system of vehicle is very important because it has an effect on ride comfort and safety. And the leaf spring is one of the major parts of commercial vehicle. By that reason it has to be designed to operate under severe condition to ensure enough endurance. But the traditional method for fatigue design needs repeated fatigue tests for each design according to its geometry, material, and operating condition. This means that a lot of time and money is needed for those tests. Thus, in this paper, a fatigue design method for leaf spring based on numerical analysis is proposed. At first, stress analysis is performed to get the stress under operation load or rig tests. And fatigue analysis is performed to get the fatigue life and to ensure the safety of leaf spring. Through this study, design parameters that play vital role in fatigue life of the leaf spring can be found out.

Friction materials with three different formulations containing different solid lubricants were investigated to study the role of lubricants on the friction performance. The three friction materials contained 10 vol.% graphite, 7 vol.% graphite + 3 vol.% Sb2S3, and 7 vol.% graphite + 3 vol.% MoS2, respectively, with the same amount of other ingredients. Results of this work showed that each formulation had advantages and disadvantages. The friction materials containing two lubricants (graphite + MoS2 or Sb2S3) showed better resistance to fading and improved friction stability than the friction material containing only graphite. However, the friction materials with two lubricants showed disadvantages on anti-fading, wear resistance, and DTV generation.

The most popular issues nowadays in the automotive industry include reduction of environmental impacts by emission materials from automobiles as well as improvement of fuel economy. This paper deals with development of a ¡mild-hybrid¡ system for a city bus as an effort to increase fuel economy in a relatively reasonable expense. Three different technical tactics are employed; an engine is shut down at an engine idle state, a vehicle kinetic energy when the bus is decelerated is re-saved to a battery in the form of electricity, and finally the radiator cooling fan is operated by an electric motor using the saved electric energy with an optimal speed control. It has been demonstrated through the driving tests in a specific city mode, ¡Suwon city mode¡, that an average fuel economy is improved more than 12%, and the system can be a feasible choice in a city bus running in a city mode experiencing many stop and go¡s.

Propensity of cold judder was studied by investigating the correlation between the microstructure of gray iron brake disks and friction properties of commercial brake linings. Based on a brake disk for a mid-size passenger car, gray iron disks with 6 different microstructures were manufactured by changing the carbon equivalent (C.E.) and cooling speed in a commercial manufacturing facility. Graphite morphology of the gray iron changed proportionally according to the C.E. and cooling speeds, exhibiting longer graphite flakes with high C.E. at slow cooling speeds. After screening tests of 23 commercial brake linings, 4 different brake linings (two non-steel and two low-steel linings with high μ and low μ) were selected for parasitic drag tests. Results showed that the preferential disk wear was pronounced in the case of using low steel linings and the trend was marked with the disks containing short graphite flakes.

An NAO friction material (low-steel type) containing 15 ingredients was investigated to study the role of transfer film on the coefficient of friction, friction oscillation, and fade resistance. The friction material specimens containing extra 100% of each ingredient were tested using a pad-on-disk type tribotester. A non-destructive method of measuring the transfer film was developed by considering the electrical resistance of the transfer film. Results showed that solid lubricants and iron powder assisted transfer film formation on the rotor surface and abrasive ingredients tended to remove the film. No apparent relationship between transfer film thickness and the average friction coefficient was found in this experiment. Fade resistance was also found to be independent of the transfer film thickness when the stable film was formed on the rotor surface at elevated temperatures. On the other hand, the transfer film on the rotor surface reduced the amplitude of friction oscillation.

In this study, two-phase flow simulations have been performed for the intake system of a commercial truck. The intake duct, which is the first component in heavy-duty engine, is located in the upper side of a cabin. The flow in the intake system is a typical two-phase flow with the air as the continuous phase and the water as the dispersed phase during rainy weather. The numerical two-phase simulation is performed by using the Largrangian model as implemented in STAR-CD. The influence of the water droplets on the airflow as well as droplet break-up and interactions of the droplets with the walls can be taken into account. Two and three cyclone model inside the intake system have been investigated by numerical simulations. The computational results can be used to get a better understanding of the physics of the flow inside the intake system and to optimize the water separation.