Search Results

Understanding the causal loop from injection to combustion in modern direct injection engines is essential to improve combustion and reduce emissions. In this work, the section from injection to fuel-evaporation in this causal loop was investigated using different optical measurement techniques, with a focus on drop size measurements using Phase Doppler Anemometry (PDA). One spray jet of a modern DISI multi-hole injector was investigated using gasoline RON 95 fuel and two single component alkane fuels (n-hexane / n-decane). In a first step the macroscopic spray formation and propagation of this spray jet were studied using a 2D-Mie-scattering technique in an optical injection chamber at homogenous charge DISI conditions. Furthermore, the droplet size distribution and mean diameter were determined spatially and temporally resolved for an ambient pressure of 0.3MPa and different ambient temperature (323K / 423K / 523K) conditions in the optical chamber using Phase Doppler Anemometry.

The influence of fuel composition on sprays was studied in an injection chamber at DISI conditions with late injection timing. Fuels with high, mid and low volatility (n-hexane, n-heptane, n-decane) and a 3-component mixture with similar fuel properties like gasoline were investigated. The injection conditions were chosen to model suppressed or rapid evaporation. Mie scattering imaging and phase Doppler anemometry were used to investigate the liquid spray structure. A spray model was set up applying the CFD-Code OpenFOAM. The atomization was found to be different for n-decane that showed a smaller average droplet size due to viscosity dependence of injected mass. And for evaporating conditions, a stratification of the vapor components in the 3-component fuel spray was observed.

Combustion processes with partially or fully premixed cylinder load combined with self-ignition provide high combustion efficiency and low emissions of Nitrogen Oxides (NOx) and particulate matter at the same time. Since the number of diesel operated passenger cars is still rising, it would be interesting, if such a combustion concept can be realized in an ordinary DI-Diesel engine which is operated with conventional diesel fuel. In this study, the influence of nozzle geometry, Tintake, pTDC and injection timing on the functioning chain of combustion was analyzed in a transparent single-cylinder diesel engine equipped with a common rail injection system by means of optical measurement techniques. Simultaneously, different optical diagnostics (laser-based and non laser-based) were used to study the fuel distribution, ignition and combustion in the combustion chamber of the optically accessible diesel engine. The liquid fuel was visualized by Mie scattering at 532nm.

Direct gasoline injection is one major approach in reducing fuel consumption to fulfill the stages of CO2 reduction commitments in Europe from today until 2008. One effort is to unthrottle the gasoline engine during idle and partial load utilizing charge stratification. This may be realized by using different combustion concepts. This paper shows the analysis of mixture preparation for three different types of direct injected gasoline engines. Each engine was driven with two injectors which have two different atomization concepts. The engine types draw a clear dividing line between their combustion concepts. The injectors were analyzed in a pressure chamber, in an optical engine, and in an actual 1-cylinder engine. The formation of wall-film in wall-guided combustion systems will be discussed. Several important injector and engine parameters for fuel direct injection are pointed out.

Pre-chamber ignition systems enable the combustion of homogeneous lean mixtures in internal combustion engines with significantly increased thermal efficiency. Such ignition systems provide a much higher ignition energy compared to a common spark ignition by burning a small portion of the charge in a separate chamber, generating multiple ignition sites in the main combustion chamber and increasing the turbulent flame speed. Pre-chamber ignition systems are commonly used in large natural gas engines but the integration in automotive engines is not feasible so far due to the lack of suitable fuelling systems needed to keep the pre-chamber mixture stoichiometric at lean operation of the engine. Based on preliminary investigations we developed an ignition system with fuelled pre-chamber for automotive engines utilizing the available space for the conventional spark plug.

The fuel spray behavior in the near nozzle region of a gasoline injector is challenging to predict due to existing pressure gradients and turbulences of the internal flow and in-nozzle cavitation. Therefore, statistical parameters for spray characterization through experiments must be considered. The characterization of spray velocity fields in the near-nozzle region is of particular importance as the velocity information is crucial in understanding the hydrodynamic processes which take place further downstream during fuel atomization and mixture formation. This knowledge is needed in order to optimize injector nozzles for future requirements. In this study, the results of three experimental approaches for determination of spray velocity in the near-nozzle region are presented. Two different injector nozzle types were measured through high-speed shadowgraph imaging, Laser Doppler Anemometry (LDA) and X-ray imaging.

Multi-hole DI injectors are being adopted in the advanced downsized DISI ICE powertrain in the automotive industry worldwide because of their robustness and cost-performance. Although their injector design and spray resembles those of DI diesel injectors, there are many basic but distinct differences due to different injection pressure and fuel properties, the sac design, lower L/D aspect ratios in the nozzle hole, closer spray-to-spray angle and hense interactions. This paper used Phase-Contrast X ray techniques to visualize the spray near a 3-hole DI gasoline research model injector exit and compared to the visible light visualization and the internal flow predictions using with multi-dimensional multi-phase CFD simulations. The results show that strong interactions of the vortex strings, cavitation, and turbulence in and near the nozzles make the multi-phase turbulent flow very complicated and dominate the near nozzle breakup mechanisms quite unlike those of diesel injections.

A previous study by the authors has shown an efficiency benefit of up to Δηi = 10 % for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine compared to the homogeneous stoichiometric operation with port fuel injection (PFI). While best efficiencies appeared at extremely lean operation at λ = 3.2, minimum HC emissions were found at λ = 2. The increasing HC emissions and narrow ignition time frames in the extremely lean stratified operation have given the need for a detailed analysis. To further investigate the mixture formation and flame propagation und these conditions, an optically accessible single-cylinder engine was used. The mixture formation and the flame luminosity have been investigated in two perpendicular planes inside the combustion chamber.

Biofuels and alternative fuels are increasingly being blended with conventional gasoline fuel to decrease overall CO₂ emissions. A promising way to achieve this is the use of DISI (direct-injection spark-ignition) technology. However, depending on temperature, pressure, chemical composition and the spark timing, unwanted pre-ignition may occur. Despite higher compression ratios, this engine knock can be decreased by lowering the mixing temperature. This results from the larger fuel evaporation enthalpy of certain biofuels which provides a non-homogeneous mixture throughout the combustion chamber. This work focuses on estimating the biofuel evaporation rate from absolute local vapor temperature and concentration. Measurements conducted in a high temperature/pressure cell using a multi-hole injector are carried out by applying planar, 2-line, laser-induced fluorescence and phase doppler interferometry.

Differences in thermo-physical parameters of fuels have high impact on the ignition, combustion and emission. Pure rapeseed FAME and diesel fuel with a cetane number of 60 have been compared to reference fuel. In an optical accessible vessel the fuels have been injected in order to investigate the spray, the ignition and soot formation. The high cetane number fuel showed similar behavior in spray phase to the reference fuel but the FAME fuel is more present at all operating points due to low volatile fuel components. The ignition and combustion process was investigated via chemical luminescence (CL) and laser induced incandescence (LII). In engine investigations a reduced ignition delay is detected in case of high cetane-number. The more sensitive optical techniques show differences in the combustion process. The ignition behavior of the reference fuel and the increased cetane number fuel were similar until the cetane increaser of the high cetane fuel came into effect.

New energy scenarios for decentralised stationary energy supply based on Liquid Organic Hydrogen Carriers (LOHC) offer an attractive application for hydrogen engines and are a reason why hydrogen engines become topical again. Since hydrogen stored in LOHCs is released under ambient pressure and temperatures of over 200°C, compression and cooling of the hydrogen is needed, lowering the system's overall efficiency. Direct injection of hydrogen is advantageous due to its low volumetric energy density and the tendency towards pre-ignition. The development objective is an injection and combustion strategy for an engine in the performance category below 15 kW and the described fuel supply scenario. Therefore, an one dimensional simulation model of the engine and the hydrogen supplying compressor was built. The simulation results show a large influence of the injection pressure on engine efficiency due to the hydrogen supplying compressor.

In spark-ignition engines, high exhaust gas recirculation (EGR) rates have demonstrated their potential in reducing fuel consumption and emissions. However, irregular combustion at high residual gas concentrations limits the EGR rates. The following study presents a strategy that has been developed to investigate the influence of complex charge motion on mixture formation and combustion for high residual gas concentrations with the aim of extending these limits. An optically accessible single-cylinder SI Engine with direct injection was used to measure the charge distribution by means of laser induced fluorescence (LIF). A special device inside the inlet pipe gave the possibility to generate a defined swirl motion overlaying a tumble motion given by the design of the inlet ports.

Two-dimensional Mie and LIEF techniques were applied to investigate the spray formation of a high pressure gasoline swirl injector in a constant volume chamber. The results obtained provide information on the propagation of liquid fuel and fuel vapor for different fuel pressures and ambient conditions. Spray parameters like tip penetration, cone angles and two new defined parameters describing the radial fuel distribution were used to quantify the fuel distributions measured. Simultaneous detection of liquid and vapor fuel was applied to study the influence of ambient temperature, injector temperature and ambient pressure on the evaporating spray.

The introduction of the so called Emission Controlled Areas within the IMO Tier III legislation forces manufacturers of maritime propulsion systems to adherence to stringent emission thresholds. Dual fuel combustion, which is characterized by the injection of a small amount of fuel oil to ignite a premixed natural gas air mixture, constitutes an option to meet this target. At high diesel substitution rates and very short pilot injection events, the injector is operated in the ballistic regime. This influences spray penetration, mixture formation and ignition behavior. In the present work, a seven-hole dual fuel injector was measured in a combustion chamber to provide data for the generation of a CFD model using the commercial code AVL FIRE®. The liquid and the vapor phase of the fuel spray were quantified by Mie-scattering and Schlieren-imaging technique for different chamber conditions.

In DISI engines spray distribution and atomization directly influence mixture formation, the quality of combustion and the resulting emissions. Constant Volume Chambers (CVC) are commonly used to characterize sprays of gasoline injectors. The CVCs provide good optical access but the flow condition of the engine cannot be reproduced. Optically accessible engines in contrast deliver realistic flow conditions but have restricted optical access. In former investigations we compared the spray propagation of different injectors in constant volume chambers and in optical accessible engines. These results showed a clear difference of the spray propagation in the CVC and the engine, especially at high charge motion conditions in the engine. To find an appropriate way to investigate the impact of different charge motion a flow channel was built with adjustable crossflow velocities from 5-50 m/s. The spray propagation during the injection process was measured with high-speed shadowgraphy.

In a study using a single-cylinder engine a significant potential in fuel efficiency and emission reduction was found for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine. The control of the mixture formation process appeared to be critical to ensure stable inflammation of the mixture. Therefore, optical investigations of the mixture formation were performed on a geometric equivalent, optically accessible single-cylinder engine to investigate the correlation of mixture formation and inflammability. The two optical measurement techniques infrared (IR) absorption and laser-induced fluorescence (LIF) were employed. Mid-wavelength IR absorption appeared to be qualified for a global visualization of natural gas injection; LIF allows to quantify the equivalence ratio inside a detection level. While LIF measurements require complex equipment, the IR setup consists merely of a black body heater and a mid-wavelength sensitive IR camera.

Modern concepts of downsized DI gasoline engines set up high requirements on the injection system to meet the emission targets. The fundamental knowledge and understanding of spray propagation physics are essential for the development of nozzles and injection strategies, due to reduced displacements in combination with the continuing trend of elevated fuel pressures. A detailed analysis of micro- and macroscopic spray parameters was carried out using a multihole solenoid driven DI injector. The measurements were performed in a continuously scavenged pressure chamber with full optical access. Fuel pressure up to 38MPa and backpressures in a range from 0.03 - 0.2 MPa were varied. Optical investigations were done by Shadowgraphy imaging and Phase Doppler Anemometry. The combination of micro- and macroscopic spray results are used to discuss the propagation behaviour of gasoline spray.

Hydrogen engines represent an economic alternative to fuel cells for future energy scenarios based on Liquid Organic Hydrogen Carriers (LOHC). This scenario incorporates LOHCs to store hydrogen from fluctuating renewable energy sources and deliver it to decentralised power generation units. Hydrogen engines were deeply investigated in the past decade and the results show efficiencies similar to CI engines. Due to the low energy density and tendency towards pre-ignition of hydrogen, the key element to reach high efficiency and a safe operation is a direct injection of the hydrogen. Because high injection pressure is not available in practical applications or would reduce the possible driving range, a low injection pressure is favourable. The low density leads to large flow cross sections inside the injector, similar to CNG direct injectors. So far, some research CNG and hydrogen low pressure direct injectors were investigated, but no commercial injector is available.

Modern direct injection spark ignition (DISI) engine concepts have the drawback of higher particulate matter emission as compared to port fuel injection concepts. Especially, when driven with biofuels, the operation of DISI engines requires a deeper insight into particulate formation processes. In this study a modern optical accessible DISI engine is used. Pure isooctane, ethanol, E20 (20vol% of ethanol in isooctane) and E85 were investigated as fuels. Simultaneous OH*-chemiluminescence and soot radiation imaging was conducted by a high-speed camera system in order to separate premixed combustion with the sooting combustion. Furthermore, a laser-induced incandescence (LII) sensor was used to measure exhaust elementary carbon mass concentration. Systematically, operation points were chosen, which correspondent to the main sooting mechanisms, poolfire, mixture inhomogeneities and global low air-fuel ratio. Furthermore, they were compared to a homogenous charge combustion strategy.

Worldwide diesel fuels differ in their composition and therefore in thermo-physical properties. Some of these properties are known to have little effect on the combustion process. Others, like the cetane number, have dramatic influence on the combustion formation and thus on the heat release rate and more important the formation of soot and NOx. In an experiment series various commercially available fuel types, like EN 590 [1], ASTM D975 [2] and JIS K 2204 [3], have been compared to alternative diesel fuels such as FAME, GtL and premium diesel fuel with increased cetane number. A specially designed research injector was used in order to provide full optical access to one single fuel jet injected and combusted in a constant volume vessel. First, the liquid fuel phase propagation has been investigated by means of Mie-scattering and the liquid penetration depth and the spray cone angle have been evaluated.