Search Results

The ongoing pursuit of improved engine efficiency and emissions is driving gasoline low-pressure loop EGR systems into production around the globe. The Dedicated EGR (D-EGR®) engine was developed to minimize some of the challenges of cooled EGR while maintaining its advantages. The D-EGR engine is a high efficiency, low emissions internal combustion engine for automotive and off-highway applications. The core of the engine development focused on a unique concept that combines the efficiency improvements associated with recirculated exhaust gas and the efficiency improvements associated with fuel reformation. To outline the differences of the new engine concept with a conventional LPL EGR setup, a turbocharged 2.0 L PFI engine was modified to operate in both modes. The second part of the cooled EGR engine concept comparison investigates efficiency, knock resistance, combustion stability, and maximum load potential at high load conditions.

A series of ignition systems were evaluated for their suitability for high-EGR SI engine applications. Testing was performed in a constant-volume combustion chamber and in a single-cylinder research engine, with EGR rates of up to 40% evaluated. All of the evaluated systems were able to initiate combustion at a simulated 20% EGR level, but not all of the resulting combustion rates were adequate for stable engine operation. High energy spark discharge systems were better, and could ignite a flame at up to 40% simulated EGR, though again the combustion rates were slow relative to that required for stable engine performance. The most effective systems for stable combustion at high EGR rates were systems which created a large effective flame kernel and/or a long kernel lifetime, such as a torch-style prechamber spark plug or a corona discharge igniter.

The spark ignition (SI) engine has been known to exhibit several different abnormal combustion phenomena, such as knock or pre-ignition, which have been addressed with improved engine design or control schemes. However, in highly boosted SI engines - where the engine displacement is reduced and turbocharging is employed to increase specific power - a new combustion phenomenon, described as Low-Speed Pre-Ignition (LSPI), has been exhibited. LSPI is characterized as a pre-ignition event typically followed by heavy knock, which has the potential to cause degradation of the engine. However, because LSPI events occur only sporadically and in an uncontrolled fashion, it is difficult to identify the causes for this phenomenon and to develop solutions to suppress it. Some countermeasures exist that OEMs can use to avoid LSPI, such as load limiting, but these have drawbacks.

Downsizing is an important concept to reduce fuel consumption as well as emissions of spark ignition engines. Engine displacement is reduced in order to shift operating points from lower part load into regions of the operating map with higher efficiency and thus lower specific fuel consumption [ 1 ]. Since maximum power in full load operation decreases due to the reduction of displacement, engines are boosted (turbocharging or supercharging), which leads to a higher specific loading of the engines. Hence, a new combustion phenomenon has been observed at high loads and low engine speed and is referred to as Low-Speed Pre-Ignition or LSPI. In cycles with LSPI, the air/fuel mixture is ignited prior to the spark which results in the initial flame propagation quickly transforming into heavy engine knock. Very high pressure rise rates and peak cylinder pressures could exceed design pressure limits, which in turn could lead to degradation of the engine.

A novel continuous inductive discharge ignition system has been developed that allows for variable duration ignition events in SI engines. The system uses a dual-coil design, where two coils are connected by a diode, combined with the multi-striking coil concept, to generate a continuous current flow through the spark plug. The current level and duration can be regulated by controlling the number of re-strikes that each coil performs or the energy density the primary coils are charged to. Compared to other extended duration systems, this system allows for fairly high current levels during the entire discharge event while avoiding the extremely high discharge levels associated with other, shorter duration, high energy ignition systems (e.g. the plasma jet [ 1 , 2 ], railplug [ 3 ] or laser ignition systems [ 4 , 5 , 6 , 7 , 8 ].

The spark ignition (SI) engine has been known to exhibit several different abnormal combustion phenomena, such as knock or pre-ignition, which have been addressed with improved engine design or control schemes. However, in highly boosted SI engines, Low-Speed Pre-Ignition (LSPI), a pre-ignition event typically followed by heavy knock, has developed into a topic of major interest due to its potential for engine damage. Previous experiments associated increases in hydrocarbon emissions with the blowdown event of an LSPI cycle [1]. Also, the same experiments showed that there was a dependency of the LSPI activity on fuel and/or lubricant compositions [1]. Based on these findings it was hypothesized that accumulated hydrocarbons play a role in LSPI and are consumed during LSPI events. A potential source for accumulated HC is the top land piston crevice.

A quasidimensional engine simulation which uses the concepts of fractal geometry to model the effects of turbulence on flame propagation in a homogeneous charge SI engine has been developed. Heat transfer and blowby/crevice flow submodels are included in this code and the submodels chosen are found to be reasonable. The model predictions of cylinder pressure histories are then compared with experimental data over a range of loads, equivalence ratios, and engine speeds. The model is not adjusted in any manner to yield better agreement with the data, other than by tuning the simple turbulence model used so as to yield agreement with data for the nonreacting flow. However, current information about the flame wrinkling scales in an engine is inadequate. Therefore, predictions are made for three different assumptions about the flame wrinkling scales which span the range of physically possible scales.

An investigation of cyclic variability in a spark ignition engine is reported. Specifically, the predictions of an engine code have been compared with experimental data obtained using a well-characterized SI engine. The engine used for the experimental work and modeled in the code is the single cylinder research engine developed at Sandia National Laboratories and now operating at Drexel University. The data used for comparison were cylinder pressure histories for 110 engine cycles gathered during operation at a single engine operating condition. The code allows the various factors that could influence cyclic variability to be examined independently. Specifically, a model has been used to independently examine the effects of variations in equivalence ratio and of the turbulence intensity on cycle-to-cycle variations in the peak cylinder pressure, the crankangle of occurrence of peak pressure, the flame development angle, and the rapid burning angle.

Initial investigations of a new type of high energy ignitor for I.C. engines are described. The ignitor is a miniaturized railgun, or “railplug.” The railplug produces a relatively large mass of high velocity plasma. These characteristics may be advantageous for initiating combustion in a number of different applications. Unlike a plasma jet ignitor, the railplug plasma is driven not only by thermodynamic expansion, but by electromagnetic forces as well. Four experimental railplug designs were evaluated using schlieren and shadowgraphy visualization to examine plasma movement and shape. Railplug current and voltage were also measured. One railplug consisting of two unenclosed parallel rails was used to demonstrate the electromagnetically induced motion of the plasma at ambient conditions. Schlieren photos showed that the plasma plume moves strongly in the direction of the electromagnetic Lorentz forces.

The performance and efficiency of spark ignited gasoline engines is often limited by end-gas knock. In particular, when operating the engine at high loads, combustion phasing is retarded to prevent knock, resulting in a significant reduction of engine efficiency. Since the invention of the spark ignition (SI) engine, much work has been devoted to improve and regulate fuel characteristics, such as octane number, to suppress engine knock. The auto-ignition tendency of the engine lubricant however, as described by cetane number (CN), has received little attention, as it has been assumed that engine lubricant effects on knock are insignificant, primarily due to low levels of average oil consumption. However, with modern SI engines being developed to operate at higher loads and closer to knock limits, the reactivity of engine lubricants can impact the knock behavior.

Condensation of fuel vapor on the cold surfaces within the combustion chamber is investigated as a possible mechanism for increased HC emissions from SI engines during cold start. A one-dimensional, transient, mass diffusion analysis is used to examine the condensation of single-species fuels on the surfaces of the combustion chamber as the pressure within the cylinder rises during compression and combustion, and re-vaporization during expansion, blowdown, and exhaust. The effects of wall temperature, fuel volatility, and engine load and speed on this mechanism are also discussed. This analysis shows that low-volatility fuel components can condense on the surfaces of the combustion chamber when the surface temperatures are sufficiently low. This condensed fuel may re-vaporize during the power and exhaust strokes, or it may remain in the combustion chamber until surface temperatures rise, perhaps tens of seconds later.

This paper presents the results of an experimental investigation of the fuel-air mixing process in a port-fuel-injected, 4-valve, spark-ignited engine that was motored to simulate cold cranking and start-up conditions. An infrared fiber-optic instrumented spark plug probe was used to measure the local, crank angle resolved, fuel concentration in the vicinity of the spark gap of a single-cylinder research engine with a production head and fuel injector. The crank-angle resolved fuel concentrations were compared for various injection timings including open-intake-valve (OIV) and closed-intake-valve (CIV) injection, using federal certification gasoline. In addition, the effects of speed, intake manifold pressure, and injected fuel mass were examined.

An electronic particulate matter sensor (EPMS) developed at the University of Texas was used to characterize exhaust gases from a single-cylinder diesel engine and a light-duty diesel vehicle. Measurements were made during transient tip-in events with multiple sensor configurations in the single-cylinder engine. The sensor was operated in two modes: one with the electric field energized, and the other with no electric field present. In each mode, different characteristic signals were produced in response to a tip-in event, highlighting the two primary mechanisms of sensor operation. The sensor responded to both the natural charge of the particulate matter (PM) emitted from the engine, and was also found to create a signal by charging neutral particles. The characteristics of the two mechanisms of operation are discussed as well as their implications on the placement and operation of the sensor.

Trucks operating in inter-modal (drayage) operation in and around port and rail terminals, are responsible for a large proportion of the emissions of NOX, which are problematic for the air quality of the Houston and Dallas/Ft. Worth metro areas. A standard test cycle, called the Texas Dray Truck Cycle, was developed to represent the operation of heavy-duty diesel trucks in dray operations. The test cycle reflects the substantial time spent at idle (~45%) and the high intensity of the on-road portions. This test cycle was then used in the SAE J1321 test protocol to evaluate the effect on fuel consumption and NOX emissions of retrofitting dray trucks with light-weight, low-rolling resistance wide-single tires. In on-track testing, a reduction in fuel consumption of 8.7% was seen, and NOX emissions were reduced by 3.8% with the wide single tires compared to the conventional tires.

A railplug is a new type of ignitor for SI engines. A model for optimizing energy deposition in a railplug ignition system is developed. The model is experimentally validated using a low voltage railplug ignition circuit. The effect of various ignition circuit parameters on the energy deposition and its rate are discussed. Durability of railplugs is an important factor in railplug circuit design. As for all spark ignitors, durability of a railplug decreases as energy deposition is increased. Therefore recommendations are made to minimize wear and increase durability, while depositing sufficient energy to attain ignition, using a railplug.

In order to determine the factors that affect fuel economy quantitatively, the power flows through the major powertrain components were measured during operation over transient cycles. The fuel consumption rate and torque and speed of the engine output and axle shafts were measured to assess the power flows in a vehicle with a CVT. The measured power flows were converted to energy loss for each component to get the efficiency. Tests were done at Phase 1 and Phase 3 of the FTP and for two different CVT shift modes. The measured energy distributions were compared with those from the ADVISOR simulation and to results from the PNGV study. For both the Hot 505 and the Cold 505, and for both shift modes, the major powertrain loss occurs in the engine, including or excluding standby losses. However, the efficiency of the drivetrain/transmission is important because it influences the efficiency of the engine.

The University of Texas 2000 Ethanol Vehicle Challenge team remains focused on cold start, cold drivability, fuel economy, and emissions reduction for our 2000 Ethanol Vehicle Challenge entry. We used the stock PCM for all control functions except control of an innovative cold-start system our team designed. The primary modifications for improved emissions control involved ceramic coating of the exhaust manifolds, use of close-coupled ethanol-specific catalysts, use of a moddified version of the California Emissions Calibrated PCM, and our cold-start system that eliminates the need to overfuel the engine at the beginning of the FTP. Additionally, we eliminated EGR at high load to improve power density. Major modifications, such as increasing the compression ratio or pressure boosting, were eliminated from consideration due to cost, complexity, reliability, or emissions penalties.

An optical access engine was used to image the liquid film evaporation off the piston of a simulated direct injected gasoline engine. A directional injector probe was used to inject liquid fuel (gasoline, i-octane and n-pentane) directly onto the piston of an engine primarily fueled on propane. The engine was run at idle conditions (750 RPM and closed throttle) and at the Ford World Wide Mapping Point (1500 RPM and 262 kPa BMEP). Mie scattering images show the liquid exiting the injector probe as a stream and directly impacting the piston top. Schlieren imaging was used to show the fuel vaporizing off the piston top late in the expansion stroke and during the exhaust stroke. Previous emissions tests showed that the presence of liquid fuel on in-cylinder surfaces increases engine-out hydrocarbon emissions.

Piston wetting can be isolated from the other sources of HC emissions from DISI engines by operating the engine predominantly on a gaseous fuel and using an injector probe to impact a small amount of liquid fuel on the piston top. This results in a marked increase in HC emissions. In a previous study, we used a variety of pure liquid hydrocarbon fuels to examine the influence of fuel volatility and structure on the HC emissions due to piston wetting. It was shown that the HC emissions correspond to the Leidenfrost effect: fuels with very low boiling points yield high HCs and those with a boiling point near or above the piston temperature produce much lower HCs. All of these prior tests of fuel effects were performed at a single operating condition: the Ford World Wide Mapping Point (WWMP). In the present study, the effects of load and engine speed are examined.

Improved submodels for use in a dynamic engine/vehicle model have been developed and the resulting code has been used to analyze the tip-in, tip-out behavior of a computer-controlled port fuel injected SI engine. This code consists of four submodels. The intake simulation submodel is similar to prior intake models, but some refinements have been made to the fuel flow model to more properly simulate a timed port injection system, and it is believed that these refinements may be of general interest. A general purpose engine simulation code has been used as a subroutine for the cycle simulation submodel. A conventional vehicle simulation submodel is also included in the model formulation. Perhaps most importantly, a submodel has been developed that explicitly simulates the response of the on-board computer (ECM) control system.