Search Results

Standard

SPECIFICATION DEFINITIONS-OFF-ROAD WORK MACHINES

1978-06-01

HISTORICAL

J1234_197806

This standard defines the more commonly used terms applicable to the majority of the machines defined in SAE J1057a and/or referenced by category in SAE J1116. Other SAE Standards will be used, when necessary, to define terms peculiar to a certain class or type of machine. Such other standards will be in accord with SAE J1234.

Standard

Cutting Edge—Optional Cross-Sections and Dimensions Loader Straight

2006-02-05

HISTORICAL

J1581_200602

The purpose of this SAE Recommended Practice is to specify dimensions for loader straight cutting edge cross sections without holes and with bolt holes for mounting bolt-on teeth and tooth adaptors on loader buckets described by SAE J731. This recommended practice is intended to supplement SAE J1303 and SAE J1304 with cross sections for heavier duty applications, by identifying larger blunts, greater bevel angles, larger bolt holes, and greater bolt spacing.

Standard

Nomenclature - Hydraulic Backhoes

2018-11-20

HISTORICAL

J326_201811

This SAE standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.

Standard

Nomenclature - Hydraulic Backhoes

2012-11-01

HISTORICAL

J326_201211

This SAE Standard includes hydraulic backhoes which have no more than 190 degrees of rotational swing, and are mounted on wheel tractors and crawler tractors. Illustrations used are not intended to include all existing commercial machines or to be exact descriptions of any particular machine. The illustrations have been chosen to describe the principles to be used in applying this standard.

Standard

Hole Spacing for Scraper and Dozer Cutting Edges

2006-02-01

HISTORICAL

J737_200602

This standard is intended for cutting edge sections used on: a Tractor-scrapers as described in SAE J1057 and J728. b Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation.

Standard

Loading Ability Test Procedure - Scrapers

2011-10-27

CURRENT

J764_201110

This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)

Standard

Cutting Edge—Cross Sections Loader Straight

2006-02-05

HISTORICAL

J1303_200602

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85.

Standard

Cutting Edge - Cross Sections Loader Straight

2011-10-25

CURRENT

J1303_201110

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled, cast, forged, flame cut, and machined cutting edge sections. Straight cutting edges are defined as those whose leading edge and rear edge are parallel and, thus, are of constant cross section. For "straight cutting edge sections with bolt holes," see SAE J1304 FEB85. NOTE—For some heavy duty applications, cross sections with larger blunts and greater bevel angles may be required.

Standard

Cutting Edge—Cross Sections Loader Straight with Bolt Holes

2006-02-05

HISTORICAL

J1304_200602

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters.

Standard

Cutting Edge - Cross Sections Loader Straight with Bolt Holes

2011-10-25

CURRENT

J1304_201110

For cutting edges used on buckets for loaders defined in SAE J1057a. The dimensions are applicable to rolled and machined sections only. Cutting edge cross section thickness is limited to a maximum of 35 mm. Bolt-on tooth adapters are rarely used on loader buckets with cutting edge thicknesses in excess of 35 mm. This recommended practice applies only to straight cutting edges defined as those whose leading edge and rear edge are parallel and thus are of constant cross section. Overall cross sections to which bolt holes were added as indicated by this recommended practice were selected from those indicated per "Cutting Edge—Cross Sections Loader Straight," SAE J1303 FEB85. Selection was based on minimum section width requirements to accommodate bolt-on tooth adapters. NOTE—For some heavy-duty applications, cross sections with larger blunts, greater bevel angles, and larger bolt holes may be required.

Standard

Hydraulic Backhoe Lift Capacity

2012-05-11

CURRENT

J31_201205

This standard applies to hydraulically operated backhoes (as defined in SAE J1116) This standard describes a uniform "over end" and "full swing arc" lifting capacity rating for backhoes. It is based on the actual capacity of the machine to lift and support a load under stable conditions. Rated lift capacities will be specified for both the boom and the dipperstick and will be shown on a lift capacity chart Figure 1.

Standard

Lift Capacity Calculation Method Scrap and Material Handlers

2019-04-15

CURRENT

J2518_201904

This SAE Standard provides a uniform method to calculate the lift capacity of scrap and material handlers, establishes definitions and specifies machine conditions for the calculations. This document applies to scrap and material handlers as defined in SAE J2506 that have a 360 degrees continuous rotating upper structure. It does not apply to equipment that is incapable of lifting a load completely off the ground. This document applies to those machines that are crawler, wheel, rail and pedestal or stationary mounted.

Standard

Cutting Edge—Curved Grader

2006-02-05

HISTORICAL

J739_200602

This SAE Standard is intended for curved cutting edge sections used on graders as defined in SAE J870 and J1057. (See Figure 1 and Table 1.) Hole conformation is further defined in SAE J740 and J1580.

Standard

Rated Operating Load for Loaders

2007-04-30

HISTORICAL

J818_200704

This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.

Standard

Specification Definitions - Hydraulic Backhoes

2018-11-14

HISTORICAL

J49_201811

This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors.

Standard

Specification Definitions - Hydraulic Backhoes

2012-07-16

HISTORICAL

J49_201207

This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing, and are mounted on wheel tractors and crawler tractors.

Standard

Specification Definitions - Hydraulic Backhoes

2020-03-04

CURRENT

J49_202003

This standard applies to hydraulic backhoes which have no more than 190 degrees of rotational swing and are mounted on wheeled tractors and crawler tractors.

Standard

SPECIFICATION DEFINITIONS-HYDRAULIC BACKHOES

1978-05-01

HISTORICAL

J49_197805

This standard includes the definitions of specification most commonly used to describe nonfull-rotating hydraulic backhoes.

Standard

Volumetric Rating of Excavator Mounted, Bucket Linkage Operated Grapples

2019-04-15

CURRENT

J2754_201904

Standard

Countersunk Square Holes for Cutting Edges and End Bits

2011-10-25

CURRENT

J740_201110

To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).