The main purpose of this test was to determine the application advantages of cushion tow hitches in comparison to the commonly used rigid tow hitch type fitted on heavy aircraft towing tractors. As diverse opinions emerged about its suitability since the introduction on the market of this new tow hitch type, it was intended to physically measure and evaluate the damping capability of this cushioned tow link when applied in practice.
This specification prescribes general requirements for marking of aircraft ground support equipment and other vehicles (i.e., runway sweepers, firetrucks, refulers, etc.), used on or near the flight line area with retro-reflective materials.
This SAE Aerospace Recommended Practice (ARP) applies to Point-Of-Use, Central and Mobile Pre-Conditioned Air Equipment. It does not apply to aircraft mounted equipment.
This SAE Recommended Practice which defines the terms and tabulates the limits of the characteristics for various protective devices used in conjunction with 400-cycle ground power for civil aircraft is intended to assist the airlines in standardizing on 400-cycle protective systems. The limits found to be acceptable in the civil aircraft industry are presented.
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
This specification establishes the requirements for the manufacture and acceptance of three-way combination (step, straight and extension) aluminum ladders for aircraft maintenance use.
The present Aerospace Recommended Practice specifies for airplane operator and tow vehicle manufacturers the basic testing requirements for towbarless tow vehicles to be used on the nose gear of conventional tricycle type landing gears of commercial civil transport aircraft with maximum ramp weight between 8600 kg (19 000 lb) and 50 000 kg (110 000 lb), commonly designated as “regional aircraft”. Its purpose is to achieve testing results, or equivalent computer modeling, demonstrating that the loads induced by the tow vehicle will not exceed the design loads of the airplane’s nose landing gear and associated structure, reduce the certified safe life limit of the nose landing gear, or otherwise compromise the airplane’s structural integrity and airworthiness certification.
The present Aerospace Recommended Practice specifies for airplane operator and tow vehicle manufacturers the basic testing requirements for towbarless tow vehicles to be used on the nose gear of conventional tricycle type landing gears of commercial civil transport aircraft with maximum ramp weight between 8,600 kg (19,000 lb) and 50,000 kg (110,000 lb), commonly designated as “regional aircraft”. Its purpose is to achieve testing results, or equivalent computer modeling, demonstrating that the loads induced by the tow vehicle will not exceed the design loads of the airplane's nose landing gear and associated structure, reduce the certified safe life limit of the nose landing gear, or otherwise compromise the airplane's structural integrity and airworthiness certification.