Search Results

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2006-03-27

HISTORICAL

J2631_200603

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2011-10-25

CURRENT

J2631_201110

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

CUMULATIVE DAMAGE ANALYSIS FOR HYDRAULIC HOSE ASSEMBLIES

1988-10-01

HISTORICAL

J1927_198810

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2009-03-27

HISTORICAL

J1927_200903

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2001-03-14

HISTORICAL

J1927_200103

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2014-06-04

CURRENT

J1927_201406

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

TESTS AND PROCEDURES FOR HIGH-TEMPERATURE TRANSMISSION OIL HOSE, LUBRICATING OIL HOSE AND HOSE ASSEMBLIES

1986-05-01

HISTORICAL

J1019_198605

This standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in: high-temperature transmission oil systems and high-temperature lubricating oil systems.

Standard

Automotive Air Brake Hose and Hose Assemblies

2017-10-12

CURRENT

J1402_201710

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.

Standard

Automotive Air Brake Hose and Hose Assemblies

2010-08-05

HISTORICAL

J1402_201008

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40 to +100 °C.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1989-05-01

HISTORICAL

J343_198905

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1987-06-01

HISTORICAL

J343_198706

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1991-04-01

HISTORICAL

J343_199104

This SAE Standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1968-06-01

HISTORICAL

J343_196806

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1990-05-01

HISTORICAL

J343_199005

This SAE Standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1986-05-01

HISTORICAL

J343_198605

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1980-06-01

HISTORICAL

J343_198006

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TESTS AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1975-04-01

HISTORICAL

J343C_197504

This standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R Series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

TEST AND PROCEDURES FOR SAE 100R SERIES HYDRAULIC HOSE AND HOSE ASSEMBLIES

1993-06-01

HISTORICAL

J343_199306

This SAE Standard is intended to establish uniform methods for the testing and performance evaluation of the SAE 100R series of hydraulic hose and hose assemblies. The specific tests and performance criteria applicable to each variety of hose and/or assemblies made therefrom are set forth in the respective specifications of SAE J517.

Standard

HYDRAULIC HOSE

1988-03-01

HISTORICAL

J517_198803

This standard covers general, dimensional, and performance specifications for several varieties of hose intended for general application in hydraulic systems on construction and industrial equipment and commercial products. These general specifications are common to and shall supplement the detailed specifications for the SAE 100R1, SAE 100R2, SAE 100R3, SAE 100R4, SAE 100R5, SAE 100R6, SAE 100R7, SAE 100R8, SAE 100R9, SAE 100R10, SAE 100R11, SAE 100R12, SAE 100R13, and SAE 100R14 hydraulic hoses set forth in the following sections.

Standard

HYDRAULIC HOSE

1989-05-01

HISTORICAL

J517_198905

This standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in sections 1 through 11 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this standard. This standard shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user.