Search Results

In this paper, results of experimental and numerical investigations of stratified exhaust gas recirculation in a single-cylinder gasoline engine are presented. The engine was operated in spray guided direct injection mode. The radial exhaust gas stratification was achieved by a spatial and temporal separated intake of exhaust gas and fresh air. The spatial separation of both fluids was realized by specially shaped baffles in the inlet ports, which prevent an early mixing up to the inlet valves. The temporally separation was performed by impulse charge valves, with one for the fresh air and one for the exhaust gas. From various possible strategies for time-dependent intake of fresh air and exhaust gas, four different strategies for the exhaust gas stratification were examined.

Engines with gasoline direct injection promise an increase in efficiency mainly due to the overall lean mixture and reduced pumping losses at part load. But the near stoichiometric combustion of the stratified mixture with high combustion temperature leads to high NOx emissions. The need for expensive lean NOx catalysts in combination with complex operation strategies may reduce the advantages in efficiency significantly. The Bowl-Prechamber-Ignition (BPI) concept with flame jet ignition was developed to ignite premixed lean mixtures in DISI engines. The mainly homogeneous lean mixture leads to low combustion temperatures and subsequently to low NOx emissions. By additional EGR a further reduction of the combustion temperature is achievable. The BPI concept is realized by a prechamber spark plug and a piston bowl. The main feature of the concept is its dual injection strategy.

Mechanical systems accomplish their tasks better when enhanced with cyber technologies. With the rapidly escalating desire for high efficiency, optimization and flexibility, these physical systems ought to be integrated with cyber technologies that enhance exhaustive manipulation of resources and productivity. The gateway for such a synergetic integration can be referred to as digitalization. Details regarding the digitization of a High-altitude Simulation chamber are discussed thoroughly in this paper. The simulation chamber was originally designed and developed as a test bench to study the characteristics of alternative fuels used in the engines of handheld tools in different altitudes and thermal conditions. It encompasses all the possible realistic temperature variations with altitude raising to 3500m above sea level.

Lean burn operation allows small cogeneration engines to achieve both high efficiency and low NOx emissions. While further mixture dilution enables future emission standards to be met, it leads to retarded combustion phasing and losses in indicated engine efficiency. In the case of naturally aspirated engines, IMEP drops due to lower fuel fraction, increasing brake specific fuel consumption. In this work, an alternative engine configuration was investigated that improves the trade-off between engine efficiency, NOx emissions and IMEP. It combines well-established means such as Miller/Atkinson valve timing and optimised intake system for a single-cylinder cogeneration engine, operating with homogenous lean air-natural gas mixture. First, the engine configuration was analysed using a detailed 1D CFD model, implying a significant potential in reaching the project target.

Small natural gas cogeneration engines usually operate with lean mixture and late combustion phasing to comply with NOx emission standards, leading to significant losses in engine efficiency. Owing to water evaporation heat and high specific heat capacity of the water vapor, leads the water injection to cooling the combustion chamber charge, which enables earlier combustion phasing, higher compression ratio and thus higher engine efficiency. Therefore, water injection enables mitigating the tradeoff between NOx emissions and engine performance, without loss in engine efficiency. The intake port injection represents, because of the low required injection pressure and the simple injector integration, a cost-effective way to introduce water into the engine. Hence, the purpose of this work is to adapt the intake port water injection timing to the charge mixture flow conditions in the intake port.

One promising alternative for meeting stringent NOx limits while attaining high engine efficiency in lean-burn operation are NOx storage catalysts (NSC), an established technology in passenger car aftertreatment systems. For this reason, a NSC system for a stationary single-cylinder CHP gas engine with a rated electric power of 5.5 kW comprising series automotive parts was developed. Main aim of the work presented in this paper was maximising NOx conversion performance and determining the overall potential of NSC aftertreatment with regard to min-NOx operation. The experiments showed that both NOx storage and reduction are highly sensitive to exhaust gas temperature and purge time. While NOx adsorption rate peaks at a NSC inlet temperature of around 290 °C, higher temperatures are beneficial for a fast desorption during the regeneration phase. Combining a relatively large catalyst (1.9 l) with a small exhaust gas mass flow leads to a low space velocity inside the NSC.