Refine Your Search

Date

Date

Hydraulic Hose and Hose Fittings Committee Defense industry Lubricants Documentation

Search Results

Viewing 1 to 20 of 26
12Next >Last >>
Sort by relevance
Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers
2006-03-27
HISTORICAL
J2631_200603
This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.
Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies
2014-06-04
CURRENT
J1927_201406
This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.
Standard

TESTS AND PROCEDURES FOR HIGH TEMPERATURE TRANSMISSION OIL HOSE, ENGINE LUBRICATING OIL HOSE, AND HOSE ASSEMBLIES
1990-06-01
HISTORICAL
J1019_199006
This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of −40 ° to 150 °C (−40 ° to 302 °F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.
Standard

Tests and Procedures for High Temperature Transmission Oil Hose, Engine Lubricating Oil Hose, and Hose Assemblies
2007-09-17
CURRENT
J1019_200709
This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of -40 to 150 degrees C (-40 to 302 degrees F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.
Standard

HYDRAULIC HOSE FITTINGS
1987-06-01
HISTORICAL
J516_198706
This standard is intended to document general and dimensional specifications for the various types and styles of hose fittings used in conjunction with hydraulic hoses specified in SAE J517 JUN87 in hydraulic systems on construction and industrial equipment and commercial products. Also included are adapter unions. The basic design and dimensional features of the fittings shown are derived from existing industry practice and include the following types: Male Dryseal pipe thread type hose fittings shall be as shown in Figs. 1A-1C for the respective styles, and in Tables 1A-1I for the applicable hoses and sizes. Male straight thread O-ring boss type hose fittings shall be as shown in Figs. 2A and 2B for the respective styles, and in Tables 2A-2F for the applicable hoses and sizes. Male 37-deg flared type hose fittings shall be as shown in Figs. 3A-3C for the respective styles, and in Tables 3A-3I for the applicable hoses and sizes.
Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS
1992-05-01
HISTORICAL
J1942_199205
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 1991,1 as the official document for nonmetallic flexible hose assemblies for marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. A Hose Assemblies Listing of the products which can be used for the applications described in Table 1 is available from SAE, Publication Number EA-1942.
Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS
1989-03-01
HISTORICAL
J1942_198903
This standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this standard establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation and maintenance of hose and hose assemblies.
Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS
1995-05-01
HISTORICAL
J1942_199505
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. SAE J1942/1 is a Hose Assemblies Listing of the products which have been certified for use in the applications described in Table 1. This document is updated each year and is available from SAE as a single copy publication.
Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS
1993-06-01
HISTORICAL
J1942_199306
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. A Hose Assemblies Listing of the products which can be used for the applications described in Table 1 is available from SAE as SAE J1942/1.
Standard

Hose and Hose Assemblies for Marine Applications
2002-11-12
HISTORICAL
J1942_200211
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
Standard

HOSE AND HOSE ASSEMBLIES FOR MARINE APPLICATIONS
1997-05-01
HISTORICAL
J1942_199705
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
Standard

Hose and Hose Assemblies for Marine Applications
2007-04-09
HISTORICAL
J1942_200704
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
Standard

Hose and Hose Assemblies for Marine Applications
2019-03-22
CURRENT
J1942_201903
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems aboard commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
Standard

Hose and Hose Assemblies for Marine Applications
2014-06-06
HISTORICAL
J1942_201406
SAE J1942, developed through the cooperative efforts of the U.S. Coast Guard and SAE, became effective August 28, 19911, as the official document for nonmetallic flexible hose assemblies for commercial marine use. This SAE Standard covers specific requirements for several styles of hose and/or hose assemblies in systems on board commercial vessels inspected and certificated by the U.S. Coast Guard. It is intended that this document establish hose constructions and performance levels that are essential to safe operations in the marine environment. Refer to SAE J1273 for selection, installation, and maintenance of hose and hose assemblies. Refer to SAE J1527 Marine Fuel Hose for hose to convey gasoline or diesel fuel aboard small craft, including pleasure craft and related small commercial craft regulated directly or by reference under 33 CFR 183 Subpart J, and boats and yachts meeting American Boat and Yacht Council standards.
Standard

HYDRAULIC HOSE
1989-05-01
HISTORICAL
J517_198905
This standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifications contained in sections 1 through 11 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this standard. This standard shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user.
Standard

Push-On Hose and Mating Hose Fittings
2014-06-06
CURRENT
J2552_201406
SAE J2552 provides limited, dimensional and general performance requirements for low pressure, field attachable, push-on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with SAE J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to always follow the manufacturers’ instructions for proper preparation and fabrication of hose assemblies.
Standard

Hose Assemblies, Rubber, Hydraulic, Steel Wire Reinforced—Part 1: Procurement Document
2001-12-11
HISTORICAL
J1754/1_200112
This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See SAE J1754-2, Table 8 for hose operating temperature ranges and identification codes.
12Next >Last >>
X