Search Results

North American drivers particularly dislike wheel dust (brake dust on their wheels). For some vehicle lines, customer surveys indicate that wheel dust is a significant concern. For this reason, Ford and its suppliers are investigating the root causes of brake dust and developing test procedures to detect wheel dust issues up-front. Intuitively, it would appear that more brake wear would lead to more wheel dust. To test this hypothesis, a gage was needed to quantitatively measure the wheel dust. Gages such as colorimeters were evaluated to measure the brightness (L*) of the wheel, which ranged from roughly 70-80% (clean) to 10-20% (very dirty). Gage R&R's and subjective ratings by a panel of 30 people were used to validate the wheel dust gages. A city traffic vehicle test and an urban dynamometer procedure were run to compare the level of wheel dust for 10 different lining types on the same vehicle.

Weld lines occur when melt flow fronts meet during the injection molding of plastic parts. It is important to investigate the weld line because the weld line area can induce potential failure of structural application. In this paper, a weld line factor (W-L factor) was adopted to describe the strength reduction to the ultimate strength due to the appearance of weld line. There were two engineering thermoplastics involved in this study, including one neat PP and one of talc filled PP plastics. The experimental design was used to investigate four main injection molding parameters (melt temperature, mold temperature, injection speed and packing pressure). Both the tensile bar samples with/without weld lines were molded at each process settings. The sample strength was obtained by the tensile tests under two levels of testing speed (5mm/min and 200mm/min) and testing temperatures (room temperature and -30°C). The results showed that different materials had various values of W-L factor.

Identifying weight reduction ideas is not difficult in the engineering world today. The difficulty is implementation! Typically Product System Teams generate long lists of weight reduction roadmap ideas, but never have time to deliver. Engineers today are too busy to run dual path programs. ‘Roadmap’ ideas sit on an opportunities list until they are “out of time” and then “fall off” the list. This paper will describe a Weight Reduction Workshop process implemented at Ford Motor Company which drives weight reduction ideas into program assumptions early in the definition of a product program. The weight reduction workshop results are: Weight Reduction Ideas Recommended Variable Cost & Investment Estimates Weight savings Cost per pound of weight saved Technical confidence Work plan for each recommended idea Ideas are also evaluated against all the program's sub-attribute requirements to insure the design functions of the component are not compromised.

This paper proposes a film dynamics model for liquid film resulting from fuel spray impinging on a wall surface. It is based on a thin film assumption and uses numerical particles to represent the film to be compatible with the particle spray models developed previously. The Lagrangian method is adopted to govern the transport of the film particles. A new, statistical treatment was introduced of the momentum exchange between the impinging spray and the wall film to account for the directional distribution of the impinging momentum. This model together with the previously published models for outgoing droplets constitutes a complete description of the spray wall impingement dynamics. For model validation, films resulting from impinging sprays on a flat surface with different impingement angles were calculated and the results were compared with the corresponding experimental measurements.

The demand for seating comfort is growing - in cars as well as trucks and other commercial vehicles. This is expected as the seat is the largest surface area of the vehicle that is in contact with the occupant. While it is predominantly luxury cars that have been equipped with climate controlled seats, there is now a clear trend toward this feature becoming available in mid-range and compact cars. The main purpose of climate controlled seats is to create an agreeable microclimate that keeps the driver comfortable. It also reduces the “stickiness” feeling which is reported by perspiring occupants on leather-covered seats. As part of the seat design process, a physical test is performed to record and evaluate the life cycle and the performance at ambient and extreme temperatures for the climate controlled seats as well as their components. The test calls for occupied and unoccupied seats at several ambient temperatures.

On the development process of truck vehicles, the dynamic behavior must be considered together with the costs involved in this development. Objective measurements, subjective evaluations and CAE simulations are used in order to support this development process. Ride comfort, acceleration and braking performance, handling and NVH are examples of attributes considered in the dynamic behavior evaluation of a tuck. Some characteristics of steering column vibration, noise and harshness are relevant to guarantee driver comfort level and vehicle safety. In this work, CAE models validated by experimental measurements were used to identify cab and vehicle modes of vibration which have significant influence on steering column response. Using this procedure, an alternative was proposed in order to decrease the amplitudes of cab and steering column vibration.

A DMS (Driver Monitoring System) is one of the most important safety features that assist in the monitoring functions and alert drivers when distraction or drowsiness is detected. The system is based in a DSMC (Driver Status Monitoring Camera) mounted in the vehicle's dash, which has a predefined set of operational requirements that must be fulfilled to guarantee the correct operation of the system. These conditions represent a trade space analysis challenge for each vehicle since both the DSMC and the underlying vehicle’s requirements must be satisfied. Relying upon the camera’s manufacturer evaluation for every iteration of the vehicle’s design has proven to be time-consuming, resources-intensive, and ineffective from the decision-making standpoint.

The increasing use of aluminum in the design of Body In White (BIW) structures created the need to develop and verify repair methodologies specific to this substrate. Over the past century, steel has been used as the primary material in the production of automotive BIW systems. While repair methods and techniques in steel have been evolving for decades, aluminum structural repair requires special attention for such common practices as welding, mechanical fastening, and the use of adhesives. This paper outlines some of the advanced verification and testing methodologies used to develop collision repair procedures for the aluminum 2003 Jaguar XJ sedan. It includes the identification of potential failure modes found in production and customer applications, the formulation of testing methodologies, CAE verification testing and component subsystem prove-out. The objective of the testing was to develop repair methodologies that meet or exceed production system performance characteristics.

With the increasing number of cars on the street, the exchange of information between those cars becomes essential to improve the driving skills of each driver, resulting in a safer, intelligent and more dynamic traffic. The task now is to make it accessible for everyone. One possible and cheap way to solve this issue is to seek possibilities on free technologies within market trends. Using the smartphone platforms, which holds a high level of embedded technologies, becoming a global communication device even to interpersonal and to social networks, and AppLink Development Kit for smartphones and vehicles integration, this paper will cover aspects about the integration of the kit to an database application based on the cloud, enabling real-time interaction between two cars. Making possible to a driver have access to information and current status of other cars to aid ones life on heavy traffic.

Researchers report an estimated 35.7 million of vehicles with touchscreens will be sold in 2019 worldwide [1]. As the use of touchscreens grows in the automotive industry, there is a need to study how driver’s arm and hand moves to access the touchscreen as well as how the driver utilizes the hardware around the touchscreen. In order to aid drivers while using the touchscreen and to minimize distractions, the drivers’ hand must be able to freely move to perform a task on the touchscreen without the trim interfering with the task. At the same time some trim may be used to support the hand and fingers while accessing the touchscreen particularly during tasks that take a longer period of time to complete. A study was performed to understand the effect of the size and the angle of a shelf placed under a touchscreen. Motion capture (Mocap) data of the hand of subjects performing two different tasks on the touchscreen was collected in the Human Occupant Package Simulator (HOPS).

A vehicle integrated sensing and analysis system has been designed, implemented, and demonstrated to nonintrusively monitor several biological signals of the driver. The biological driver signals measured by the system are the heart electrical signals or pseudo Lead-I electrocardiography (pLI-ECG), the galvanic skin response (GSR) or electrical conductance measured from the driver's fingers to palm, the palm skin temperature, the face skin temperature, and the respiration rate. The pLI-ECG and GSR measurements are made through direct contact of the driver hands with stainless steel electrodes integrated in the steering wheel rim. The temperature measurements are made with non-contacting infrared temperature sensors, also located on the steering wheel. The respiration rate was measured using a flexible thin film piezoelectric sensor affixed to the seatbelt.

Among the development phases of an automotive vehicle one can point out the definition of the main characteristics of its suspensions like for example the suspension kinematics and compliances properties. Suspension definition phase can be understood as the following scenario: given a suspension type, which hard points (geometric) and what values of stiffness for the whole system will result in a desired dynamic behavior for the vehicle as well as production feasibility. This present work intends to show the influence of some suspension properties on the global dynamic behavior of the vehicle, having as a target an efficient suspension design. In terms of global dynamic behavior this work point out some control parameters, which describe the vehicle transient and steady-state properties. Those parameters are: Yaw phase lag, understeer gradient, Steady state acceleration gain and yaw overshoot during a maneuver like brake in a turn and power-off in a curve.

This paper describes a method to validate in-vehicle speech recognition by combining synthetically mixed speech and noise samples with batch speech recognition. Vehicle cabin noises are prerecorded along with the impulse response from the driver's mouth location to the cabin microphone location. These signals are combined with a catalog of speech utterances to generate a noisy speech corpus. Several factors were examined to measure their relative importance on speech recognition robustness. These include road surface and vehicle speed, climate control blower noise, and driver's seat position. A summary of the main effects from these experiments are provided with the most significant factors coming from climate control noise. Additionally, a Signal to Noise Ratio (SNR) experiment was conducted highlighting the inverse relationship with speech recognition performance.

Traditional automotive seat development has relied on a series of physical prototypes that are evaluated and refined in an iterative fashion. Costs are managed by sharing prototypes across multiple attributes. To further manage costs, many OEMs and Tier 1s have, over the past decade, started to investigate various levels of virtual prototyping. The change, which represents a dramatic paradigm shift, has been slow to materialize since virtual prototyping has not significantly reduced the required number of physical prototypes. This is related to the fact virtual seat prototyping efforts have been focused on only selected seat attributes - safety / occupant positioning and mechanical comfort are two examples. This requires that physical prototypes still be built for seat attributes like craftsmanship, durability, and thermal comfort.

This paper presents an alternative and relatively simple method which allows the use of ordinary ejector-type diluters over a wide range of sample inlet conditions including elevated pressures and temperatures. After calibration of the ejector diluter, the dilution can be accurately characterized using only the pressures at the inlet and the outlet of the diluter and the sample temperature. The method is based on a semi-empirical, stationary model taking into account the critical parameters needed to predict the dilution factor. Under steady state operation it achieves accuracies estimated to be below ±8% (95% confidence interval) for diluter inlet pressures in the range of 1000 - 4000 mbar absolute and temperatures between 20 - 200°C. Performance under actual vehicle testing conditions is evaluated upstream of the DPF for a diesel vehicle run on a chassis dynamometer.

Gasoline particulate filters (GPF) with high filtration efficiency (>80%) at zero mileage are in growing demand to meet increasingly tight vehicle emission standards for particulate matter being implemented in US, EU, China and elsewhere. Current efforts to achieve high filter performance mainly focus on fine-tuning the filter structure, such as the pore size distribution and porosity of the bare substrate, or the washcoat loading and location of catalyzed substrates. However, high filtration efficiency may have a cost in high backpressure that negatively affects engine power. On the other hand, it has been recognized in a few reports that very low amounts of ash deposits (from non-combustible residue in the exhaust) can significantly increase filtration efficiency with only a mild backpressure increase.

The ability to extract and evaluate the time history of structural deformations or crush during vehicle crashes represents a significant challenge to automotive safety researchers. Current methods are limited by the use of electro-mechanical devices such as string pots and/or linear variable displacement transducers (LVDT). Typically, one end of the transducer must be mounted to a point on the structure that will remain un-deformed during the event; the other end is then attached to the point on the structure where the deformation is to be measured. This approach measures the change in distance between these two points and is unable to resolve any movement into its respective X, Y, or Z directions. Also, the accuracy of electro-mechanical transducers is limited by their dynamic response to crash conditions. The photogrammetry technique has been used successfully in a wide variety of applications including aerial surveying, civil engineering and documentation of traffic accidents.

In Fall of 2001, a new emissions test cell was installed at Ford Motor Company that was specifically designed for precise low-level measurements (as described in Reference 6). The primary design focus for this cell was to ensure that optimal measurement capability was available to test vehicles that meet the stringent Partial Zero Emission Vehicle (PZEV) tailpipe requirements (NMOG = 10 mg/mile, NOx = 20 mg/mile). Over the past four years, there have been numerous improvements to the operational and Quality Assurance (QA) practices used in the PZEV Test Cell. Several investigations have also been performed to demonstrate the quality of its emissions measurements. Finally, a number of “lessons learned” have been documented from our experiences with PZEV measurements and with testing hybrid-electric vehicles. This paper summarizes these findings as a reference for others interested in low-level emissions measurements.

Unregulated emissions, i.e., emissions which are not currently regulated by EPA, have been measured from a 7.5 L (460 CID) PROCO engine powered vehicle operating at 50 kph on a chassis dynamometer. A dilution tube was used. Emphasis was on particulate emissions, which were characterized physically and chemically. A comparison is made to recent similar measurements on Diesel and conventional gasoline powered vehicles.

Previously fuel consumption on a drive cycle has been shown to be proportional to traction work, with an offset for powertrain losses. This model had different transfer functions for different drive cycles, performance levels, and applied powertrain technologies. Following Soltic it is shown that if fuel usage and traction work are both expressed in terms of cycle average power, a wide range of drive cycles collapse to a single transfer function, where cycle average traction power captures the drive cycle and the vehicle size. If this transfer function is then normalized by weight, i.e. by working in cycle average power/weight (P/W), a linear model is obtained where the offset is mainly a function of rated performance and applied technology. A final normalization by rated power/weight as the primary performance metric further collapses the data to express the cycle average fuel power/rated power ratio as a function of cycle average traction power/rated power ratio.