Search Results

Toyota developed a new hybrid unit “L4A0” for the new Tundra, which creates both good drivability and environmental performance. To ensure off-road, towing performance and typical truck driving characteristics, the unit is based on a transmission with a torque converter and a multi-plate lock up clutch, with a motor-generator and K0 clutch installed between the engine and transmission. The motor-generator and K0 clutch are built into a module, making it possible to create new hybrid units by combining the module with various transmissions. The unit features many different motor controls. For example, in the case of step-in acceleration input, in order to achieve the desired output torque, typically a kick-down shift is necessary [1]; however, by utilizing “L4A0” both high response and high power output is achieved even without a kick-down shift. This is accomplished by assisting the engine with the motor-generator even when the engine torque is delayed at low engine speeds.

The renewed platform of the upcoming flagship front-engine, rear-wheel drive (FR) vehicles demands high levels of driving performance, fuel efficiency and noise-vibration performance. The newly developed driveline system must balance these conflicting performance attributes by adopting new technologies. This article focuses on several technologies that were needed in order to meet the demand for noise-vibration performance and fuel efficiency. For noise-vibration performance, this article will focus on propeller shaft low frequency noise (booming noise). This noise level is determined by the propeller shaft’s excitation force and the sensitivity of differential mounting system. In regards to the propeller shaft’s excitation force, the contribution of the axial excitation force was clarified. This excitation force was decreased by adopting a double offset joint (DOJ) as the propeller shaft’s second joint and low stiffness rubber couplings as the first and third joints.

Newly developed 2VZ-FE engine for CAMRY is a 2.5-liter water cooled and V-type 6-cylinder engine exported from TOYOTA for the first time. This engine has the TOYOTA original 4-valve DOHC system. That is, exhaust camshafts driven by intake camshafts using scissors gears. By its compact configuration with the gear driven camshafts, this V-type 6-cylinder engine is mounted on a front-wheel-drive vehicle which originally had an in-line 4-cylinder engine. By increasing IVZ-FE engine displacement (for domestic), compact pentroof-type combustion chambers, optimum air-fuel ratio and ignition timing by TCCS (TOYOTA Computer Controlled System) and other technologies, a high performance 153HP/5600rpm and a large torque 155ft·lbs/4400rpm have been achieved with a low fuel consumption.

There is ever increasing interest in the issues of fossil fuel depletion, global warming, due to increased atmospheric CO2, and air pollution, all of which are due in some extent to transportation, including automobiles. Hybrid Vehicles (HVs), whose performance and usage are equivalent to existing conventional vehicles, attract lots of attention and have started to come into wider use. Meanwhile, EVs have been considered by many as the best solution for the issues mentioned above. But the technical difficulty of battery energy density is an obstruction to successful implementation. Currently the Plug-in HV (PHEV), which combines the advantages of HV and EV, is being considered as one promising solution. PHEVs can be categorized into two types, according to operating modes. The first uses battery stored energy initially, only stating the internal combustion engine when the battery is depleted. This we call the All Electric Range (AER) system.

This paper describes and discusses the result of a comprehensive simulation analysis we have carried out to clarify the effects of gear dimensions, tooth surface modification, and manufacturing error on the static transmission error of automotive hypoid gears. Three representative factors have been analyzed contact ratio, crowning and pitch error because these characteristics play the most important role in tooth dimensions, tooth surface modification and manufacturing error. The analysis has clarified the effect of each factor on gear noise, making it possible to prepare a guideline for optimal design of gear dimensions and tooth surface modification under various conditions.

For a luxury sedan, quietness is a major selling point, and a hybrid luxury sedan is expected to be especially quiet. Therefore, in the development of the hybrid luxury sedan, every possible effort is needed to reduce the hybrid system noise in order to ensure a level of quietness far superior to that of an ordinary gasoline-powered vehicle. In addition, the noise and vibration phenomena that are particular to vehicles with longitudinal power trains require special reduction technologies. This paper first describes the superior quietness of hybrid luxury vehicles in comparison with ordinary gasoline-powered vehicles. This paper then addresses the development issues of vibration during engine starting, engine booming noise, and motor noise, explaining the mechanisms by which they are generated and the technologies employed to reduce them.

The new gasoline hybrid car, “the Prius”, has achieved both two-liter class power performance and world top-class gas mileage with the new Toyota Hybrid System “THS II”. Compared with the previous THS, the electric motor drive power of the THS II has been boosted by 50% and the weight of this system has been reduced by 20%. This paper describes the NV problems caused by the improvements to the hybrid system, and the countermeasures for them. It also describes the technologies for reduction of engine start vibration. Finally an evaluation method and countermeasures against interior engine noise are described.

Vehicle weight reduction is becoming more and more important as increasingly stringent fuel economy regulations are introduced around the world. This development improved the hydraulic gear pump performance of the next-generation Active Height Control (AHC) suspension and achieved significant weight reduction of 5 kg by eliminating the auxiliary pump accumulator. To realize the necessary high-pressure with a high flow rate, the sealing performance of the pump at the tips of the gear teeth is very important. This was achieved by developing “breaking-in” technology that shaves away the aluminum housing using the gear teeth and creates zero clearance between the teeth tips and the housing. To reduce the frictional loss torque of the pump, which was identified as an issue of this technology, it was necessary to completely shave away the initial clearance in the breaking-in process.

Torque loss reduction at differential gear unit is important to improve the fuel economy of automobiles. One effective way is to decrease the viscosity of lubricants as it results in less churning loss. However, this option creates a higher potential for thin oil films, which could damage the mechanical parts. At tapered roller bearings, in particular, wear at the large end face of rollers and its counterpart, known as bearing bottom wear is one of major failure modes. To understand the wear mechanism, wear at the rolling contact surface of rollers and its counterpart, known as bearing side wear, was also observed to confirm the wear impact on the tapered roller bearings. Because gear oils are also required to avoid seizure under extreme pressure, the combination of a phosphorus anti-wear agent and a sulfurous extreme pressure agent are formulated.

Clarifying the impact of ETBE 8% blended fuel on current Japanese gasoline vehicles, under the Japan Clean Air Program II (JCAPII) we conducted exhaust emission tests, evaporative emission tests, durability tests on the exhaust after-treatment system, cold starting tests, and material immersion tests. ETBE 17% blended fuel was also investigated as a reference. The regulated exhaust emissions (CO, HC, and NOx) didn't increase with any increase of ETBE content in the fuel. In durability tests, no noticeable increase of exhaust emission after 40,000km was observed. In evaporative emissions tests, HSL (Hot Soak Loss) and DBL (Diurnal Breathing Loss) didn't increase. In cold starting tests, duration of cranking using ETBE 8% fuel was similar to that of ETBE 0%. In the material immersion tests, no influence of ETBE on these material properties was observed.

Increasing numbers of vehicles equipped with downsized, turbocharged engines have been introduced seeking for better fuel economy. LSPI (low speed pre-ignition), which can damage engine hardware, is a potential risk of the engines. We reported that engine oil formulation affects frequency of LSPI events, and formulating magnesium detergents into oil is a promising option to prevent LSPI events. From the viewpoint of achieving better fuel economy by engine oil, lowering viscosity is being required. However, it causes reduced oil film thickness and will expand boundary lubrication condition regions in some engine parts. Hence, a technology to reduce friction under boundary lubrication becomes important.

The basic concept of the Toyota mild hybrid system is to provide a smooth and reliable engine restarting method from an idling stop, while at the same time being able to drive all of the accessories during the idling stop. This concept has been realized and marketed for the first time in the world, by utilizing a newly developed simulation of belt behavior to optimize the specification of the belt and its peripheral parts.

Hydrotreated Vegetable Oil (HVO) and Sugar-to-Diesel as next-generation bio diesel fuels consist of normal and iso-paraffin, and those carbon number of paraffinic hydrocarbons and distillation characteristics are narrow distribution. These characteristics would cause to deteriorate the evaporation and mixture with air and fuel. Therefore, in this study, the effects of normal paraffin (Tridecane) and iso-paraffin (HVO) on emission characteristics and cold start performance in a diesel engine were investigated by engine dynamometer tests, cold start vehicle tests, and spray analyzer tests. From the results, it was found that normal and iso-paraffin are beneficial for HC, CO, Smoke emission reduction. In addition, isomerization is effective for the diesel engine to fulfill cold start performance, since normal paraffin of narrow carbon number distribution became solidified under low temperature and high pressure condition in a common rail system.

In recent years, electrically heated catalysts (EHCs) have been developed to achieve lower emissions. In several EHC heating methods, the direct heating method, which an electric current is applied directly to the catalyst substrate, can easily activate the catalyst before engine start-up. The research results reported on the use of the direct heating EHC to achieve significant exhaust gas purification during cold start-up [1]. From the perspective of catalyst loading, ceramics is considered to be a better material for the substrate than metal due to the difference in coefficient of thermal expansion between the catalyst and the substrate, but the EHC made of ceramics has difficulties such as controllability of the current distribution, durability and reliability of the connection between the substrate and the electrodes.

The new P710 hybrid transaxle for a mid-size 2.5-liter class vehicle was developed based on the Toyota New Global Architecture (TNGA) design philosophy to achieve a range of desired performance objects. A smaller and lighter transaxle with low mechanical loss was realized by incorporating a new gear train structure and a downsized motor. The noise of the P710 transaxle was also reduced by adopting a new damper structure.

Toyota has developed a new continuously variable transmission (CVT) called "Direct Shift-CVT" which is for 2.0-liter class vehicles. This CVT provided not only power transmission by a metal belt held with a conventional pulley but also additional gear mechanism. This CVT is developed to improve fuel efficiency, acceleration characteristic, and quietness. At this CVT, the startup low gear ratio is achieved by gear mechanism and the power is switched by clutches. Since the belt-pulley portion can be realized to be wide range by using only high gear ratio range, the input load into belt-pulley portion is reduced and unprecedented compact and high efficient belt-pulley portion is established. Consequently, the high efficiency in all fields from startup acceleration to high speed driving is achieved to improve fuel efficiency.

Toyota Motor Corporation developed the Multi Stage Hybrid System for the Lexus flagship LC500h coupe with the aim of achieving an excellent balance between fuel economy and acceleration performance. The Multi Stage Hybrid Transmission used in this new hybrid system includes a shift device located immediately after the power split device and motor. Compared with previous hybrid systems, acceleration performance is improved by increasing the driving force at low and medium vehicle speeds in lower gears, fuel economy and heat management performance are improved by reducing electrical loss by selecting the optimal gear depending on the driving state. The Multi Stage Hybrid Transmission uses a shift device with a wide gear ratio range to maximize both fuel economy and acceleration performance. The transmission was designed to achieve the appropriate size to be mounted in a new platform, as well as class-leading low noise levels for adoption in luxury vehicles.

Toyota Motor Corporation has developed an innovative 10-speed longitudinal automatic transmission called the Direct Shift-10AT. The Direct Shift-10AT is a significant contributor to the excellent dynamic performance of the Lexus LC500. A wide gear spread with close gear ratios allows for rhythmical shifting, smooth and powerful acceleration from a standing start, along with quiet and relaxed high- speed driving due to low engine speeds. The lock-up area is expanded to a wider range of vehicle speeds (excluding low-speed regions such as when starting off), by the adoption of a multi-plate lock-up clutch, a newly developed torque converter, and a high-precision controller. As a result, the shift control can match the driver's intended operation more directly because the main cause of the response delay (transient changes in engine speed (flare)) is eliminated. Furthermore, fuel economy is improved due to the adoption of low friction clutches.

Due to regulations for even lower levels of pollutants in exhaust gas, development of advanced combustion techniques and increasingly efficient catalysts has become more crucial than ever. One of the essential technologies to achieve this goal is an advanced measurement method, which can detect the characteristics of exhaust gas, such as temperature and chemical compositions, in real-time to clarify their reaction mechanisms. A direct and fast response (1ms) measurement technique was developed based on diode laser absorption spectroscopy and applied to practical engine exhaust measurement to prove the validity of this technology for various applications such as clarification of engine start phenomena and improvement of EGR controls.

This paper describes a new control technology that coordinates the operation of multiple actuators in a new hybrid electric vehicle (HEV) system consisting of a turbocharged engine, front and rear electric motors, two clutches, and a 6-speed automatic transmission. The development concept for this control technology is to achieve the driver’s desired acceleration G with a natural feeling engine speed. First, to realize linear acceleration G even while the engine is starting from EV mode, clutch hydraulic pressure reduction control is implemented. Furthermore, the engine start timing is optimized to prevent delayed drive force response by predicting the required maximum power during cranking. Second, to realize linear acceleration, this control selects the proper gear position based on the available battery power, considering noise and vibration (NV) restrictions and turbocharging response delays.