Search Results

The torsional natural frequencies of axles equipped with limited slip differential clutches depend on whether or not the tires and clutches are slipping since the effective inertia at each end of the axle is different for slipping and non-slipping conditions. Limited slip axle vibrations are typically analyzed for one tire slipping and the other not since that is the case for which the limited slip clutches are used. Vibrations often arise, however, during normal turning when both drive tires have good traction.

Since the introduction of the catalytic converter, some automobile manufacturers have questioned whether the converter is compatible with the use of the gasoline fuel additive MMT®. Concerns have generally revolved around possible interactions between combustion products of MMT® (i.e., manganese containing compounds) and catalytic converters. In particular, concern has been raised over the possibility that MMT® combustion products physically “plug” the catalyst and cause catalyst failure, where plugging refers to blockage of contiguous pores at the catalyst inlet face or within the body of the converter. In modern vehicles this could result in the illumination of the malfunction indicator light (MIL) due to storing of an on-board diagnostic (OBD) failure code pertaining to catalyst operation or failure of a vehicle inspection and maintenance (I/M) test.

Modern light-duty trucks and SUV's are designed to be aerodynamic to increase fuel economy. Such vehicle design significantly reduces the amount of air available to cool the rear axle in rear wheel drive vehicles. Reduced cooling coupled with higher power output and additional load from trailer towing operations results in higher axle operating temperatures, especially during the early operation or “break-in” phase of axle life. Higher axle operating temperatures decrease oil viscosity resulting in reduced oil film formation ability to protect against wear and contact fatigue. High temperature also shortens the useful life of gear oils. To facilitate the development of gear oils capable of reducing axle operation temperature, we have developed a laboratory simulation test method that can closely simulate actual trailer-towing driving on Baker's grade road under maximum GVCWR of close to 6,033 kg (13,300 lbs).

A vehicle fleet of seven low-mileage gasoline direct injection (GDI) vehicles from the U.S. market were tested to determine if GDI injector deposits were present causing a loss in fuel economy (FE). The real-world vehicles were tested “as-is” from the field. The data shows that, even in a deposit control additive (DCA) mandated market that uses E10 gasoline, injector deposits can still result in up to 2.7 % loss in FE. In addition, the data shows that the level of real-world FE loss is comparable to that demonstrated in the GDI injector fouling test developed to simulate real-world dirty-up of GDI vehicle injectors.

After new transmission lubricants are developed there is an extensive validation program where friction durability testing is performed on multiple clutch materials. Each durability test can run for long terms and the entire validation program can take much longer terms. A well designed lubricant and friction material will deliver the necessary friction control for construction equipment to operate at optimum level. A mechanistic construct has been evaluated to calculate friction durability in clutch systems based on fluid and surface tribological properties. Fluid properties include both boundary frictional and rheological effects. Surface properties include elastic modulus, surface roughness, asperity density and asperity tip radius. Using this mechanistic construct friction durability has been predicted.

An automatic transmission planetary gear fatigue test is used to screen lubricant performance of various automatic transmission fluids. The key use of this test is to assess the ability of a lubricant to extend or limit planetary gear system fatigue life. We study the fatigue behavior in this test and find the major failure modes are tooth macropitting, and macropitting-related tooth fracture of the sun and planetary gears (short and long pinion gears). Micropitting appears to be responsible for these gear failure modes. Macropitting is also seen on the shafts and needle rollers of the bearings. Gear tooth fracture appears to have originated from the surface as a secondary failure mode following macropitting. Bearing macropitting is initiated by geometric stress concentration. Bending fatigue failure on the sun and planetary gears also occurs but it is not a micropitting-initiated failure mode.

This paper reports its findings in three separate parts. First, a comparative study is made among existing commercial dual clutch automatic transmission fluids (DCTFs). Significant differences in fluid torque capacity, friction material compatibility and copper corrosion performance were found among the fluids. Second, both a new vehicle chassis dynamometer durability test and a SAE#2 durability procedure are offered, specifically designed for DCTs. A 2008 VW GTI did well in the severe 60,000 mile chassis dynamometer procedure. Third, a new DCT fluid is discussed.

Currently there is no axle test aimed specifically at bearing durability in automotive hypoid axles. Existing axle tests are primarily focused on gear distress and lubricant protection of gears. In light of the new test information showing axle bearing distress, there is a need to develop a new bearing durability test for automotive and truck axle lubricants. To fulfill this need, a new bearing durability test has been developed to better assess lubricant requirements for rolling element bearing durability. Although the final test of an axle lubricant is in a driven automobile or truck, an effective screening test based on actual light duty truck conditions can be used to accelerate lubricant development to enhance bearing performance in hypoid axles. This new test simulates actual road durability tests in the lab. A specific load cycle which retains the critical road test loading conditions reduces test time and helps speed up lubricant development.

Vehicle manufactures are significantly increasing the production of Direct Injection Gasoline (DIG) engines to help meet the requirements of governmental regulations and the demands of consumers. While DIG powertrains offer multiple advantages over conventional gasoline engines they can be susceptible to fuel related deposit formation, specifically within the fuel injector nozzle. Fuel injector deposits have been linked to a number of negative effects that can impact the normal operation of the engine. A DIG deposit test has been developed to evaluate Deposit Control Additives (DCA) and their effect on injector deposits. Multiple metrics for evaluating fuel injector deposits were investigated to determine a suitable method for quantifying deposit formation. Interrogation of the vehicle On-Board Diagnostic (OBD) system was identified as the optimal method for quantifying deposit formation throughout the duration of the test.

Since the mid-1990's, original equipment manufacturers (OEMs) of automobiles have been implementing torque converter clutches in automatic transmissions with a continuous, controlled slip mode, in order to improve the fuel economy of their vehicles. These Continuously Slipping Torque Converter Clutches (CSTCCs) are prone to an undesirable phenomenon commonly called shudder. This phenomenon has been attributed to specific shapes or slopes in the friction coefficient versus sliding speed curve of the fluid/clutch interface. Here, a method is explained that was developed to be able to screen fluids for shudder tendency, both in fresh and used states. Also included is a description of the reason for implementing CSTCCs, some background on shudder, and supporting data showing how the test method can distinguish between fluids that have different shudder tendencies.

To develop an automatic transmission fluid (ATF) that meets DEXRON® III-H specifications, the ATF must pass two critical tests, the GM oxidation test (GMOT) and the GM cycling test (GMCT), in addition to many other performance tests. The specification on the GMOT is that delta TAN (difference in total acid number compared with the fresh oil) at the end of the test does not exceed 3.25 while the specifications on GMCT are that delta TAN cannot exceed 2.0 and the 1-2 shift time must stay between 0.30 and 0.75 seconds throughout the test. For this work, we analyze oil oxidation and changes in oils' surface tension, drum and band surface degradation and deposit formation. We have found that with respect to the delta TAN limits of the DEXRON® III-H specification, the GMCT is more severe than the GMOT. The effect of base oil chemistry on oxidation in these tests has been quantified. Oil oxidation is not responsible for the GMCT 1-2 shift time increase.

There is still a need in the industry for engine oils that have low viscosities to improve vehicle fuel efficiency but also protect engines from wear. Viscosity modifiers (VMs) are chief additives responsible for adjusting the viscometric characteristics of automotive lubricants. Most notably, VMs have a significant impact on a lubricant's viscosity-temperature relationship as indicated by viscosity index (VI), cold cranking simulator (CCS) viscosity, and high temperature high shear (HTHS) viscosity of engine oils. Functional copolymers bearing branched, linear, or anti-wear functionalities have been synthesized and evaluated for viscometric and wear protection performance. The resulting polymers improved tribofilm formation, shear stability and CCS viscosities. Indirect benefits including Noack improvement and trim oil reduction were observed.

Sliding contact between friction surfaces occurs in numerous torque transfer elements: torque converter clutches, shifting clutches, launch or starting clutches, limited slip differential clutches, and in the meshing of gear teeth under load. The total temperature in a friction interface is the sum of the equilibrium temperature with no sliding and a transient temperature rise, the flash temperature, caused by the work done while sliding. In a wet shifting clutch the equilibrium temperature is typically the bulk oil temperature and the flash temperature is the temperature rise during clutch engagement. The flash temperature is an important factor in the performance and durability of a clutch since it affects such things as the reactivity of the sliding surfaces and lubricant constituents (e.g., oxidation) and thermal stress in the components. Knowing how high the flash temperature becomes is valuable for the formulation of ATF, gear oil, engine oil and other lubricants.

In-use vehicle regional inspection and maintenance (I/M) programs in the United States (US) and Canada generate a tremendous volume of data that provides a means for evaluating vehicle emissions compliance in actual consumer use. In this study, IM240 test data for several 1996 to 2001 vehicle models are analyzed from different regional programs in the US and Canada to confirm the suitability of using these data for evaluation of vehicles equipped with advanced emission control technology and to examine the various potential factors responsible for emissions noncompliance. Relative comparisons between US and Canadian program data are made for vehicle models used in the Alliance of Automobile Manufacturers (AAM) MMT® Test Program to examine the potential impact of differences in fuel properties on consumer experience and vehicle compliance.

Multiple plate disc clutches are used extensively for shifting gears in automatic transmissions. In the active clutches that engage or disengage during a shift the automatic transmission fluid (ATF) and friction material experience large changes in pressure, P, sliding speed, v, and temperature, T. The coefficient of friction, μ, of the ATF and friction material is a function of these variables so μ = μ(P,v,T) also changes during clutch engagement. These changes in friction coefficient can lead to noise or vibration if the ATF properties and clutch friction material are improperly matched. A theoretical understanding of what causes noise, vibration and harshness (NVH) in shifting clutches is valuable for the development of an ATF suitable for a particular friction material. Here we present a theoretical model that identifies the slope, ∂μ/∂T, of the coefficient of friction with respect to temperature as a major contributor to the damping in a clutch during engagement.

Different mechanical components in a vehicle can be made from different steel alloys with various surface treatments or coatings. Lubricant technology is needed to prevent wear and control friction on all of these different surfaces. Phosphorus compounds are the key additives that are used to control wear and they do this by forming tribofilms on surfaces. It has been shown that different operating conditions (pressures and sliding conditions) can influence the formation of tribofilms formed by different anti-wear additives. The effect of surface metallurgy and morphology on tribofilm formation is described in this paper. Our results show that additive technology can form proper tribofilms on various surfaces and the right combination of additives can be found for current and future surfaces.

A model and simulation results are presented for the torsional dynamics of a rear wheel driveline while the vehicle is coasting in a turn. The model includes the effects of road load and powertrain drag, limited slip differential clutch friction, the inertias of the vehicle, wheels, axles, differential carrier, and driveshaft, the final drive ratio, torsional stiffnesses of the axles and driveshaft, vehicle track width, and radius of the turn. The dynamics of coasting in a turn differ from powered driving due to changes in the inertia loading the driveshaft, the damping effect of the disengaged transmission, and nonlinearities in the clutch friction. Specific focus is given to vibration in the axles and driveshaft due to variations in the torque-speed slope of the clutches, which is determined by the slope of the friction coefficient ‘μ’ versus sliding speed ‘v’ in the limited slip clutches.

Improving vehicle fuel efficiency is a key market driver in the automotive industry. Typically lubricant chemists focus on reducing viscosity and friction to reduce parasitic energy losses in order to improve automotive fuel efficiency. However, in a transmission other factors may be more important. If an engine can operate at high torque levels the conversion of chemical energy in the fuel to mechanical energy is dramatically increased. However high torque levels in transmissions may cause NVH to occur. The proper combination of friction material and fluid can be used to address this issue. Friction in clutches is controlled by asperity friction and hydrodynamic friction. Asperity friction can be controlled with friction modifiers in the ATF. Hydrodynamic friction control is more complex because it involves the flow characteristics of friction materials and complex viscosity properties of the fluid.

This report focuses on an extended investigation of the durability of Dual Clutch Transmission (DCT) fluids. The performance requirements of DCT fluids differ from those of traditional step automatic transmission fluids. For that reason, key performance lab tests are discussed in this paper. Friction durability is measured with a modified version of the JASO M348 SAE#2 friction plate test. In addition, results from a vehicle chassis dynamometer test are discussed. This test involves running a 2008 Volkswagen GTI for 60,000 dynamometer miles (42,000 cycles) of severe acceleration and high speed conditions. Finally, a new DCT fluid, which performs well in these tests, offers friction stability and superior wear protection of transmission hardware, when compared to the commercial reference fluid.

When gasoline-fueled vehicles are operated in consumer service, the oil used to lubricate the engine plays a key role in engine cooling, reducing friction, maintaining efficient operation, and optimizing fuel economy. The effects of normal vehicle operation on oil deterioration have a direct impact on fuel consumption. The authors have observed substantial differences between the deterioration of engine oil and resulting fuel economy under real-world driving conditions, and the deterioration of oils and resulting fuel economy in the standard laboratory test used to assess fuel economy in North America, the Sequence VID engine test (ASTM D7589). By analyzing the data from vehicles and comparing these data to the Sequence VID the authors have proposed and evaluated several changes to the Sequence VID test that improve the correlation with real-world operation and improve test discrimination.