Search Results

TWO TYPES of bench wear tests employed by the General Motors Research Laboratories are described, and examples are given to illustrate the application of the tests to material development problems. It is shown that correlation of a bench test with service may be achieved even when the laboratory test conditions do not appear to duplicate service conditions exactly. It is postulated that this behaviour is related to the formation of certain types of surface films during the wearing process. Some preliminary results are given of a study of the influence of lubricant type and material composition on the formation of anti-wear films.

THE PURPOSE of this experiment was to determine the role of residual stresses in fatigue strength independent of other factors usually involved when residual stresses are introduced. It consisted of an investigation of the influence of residual stresses introduced by shotpeening on the fatigue strength of steel (Rockwell C hardness 48) in unidirectional bending. Residual stresses were varied by peening under various conditions of applied strain. This process introduced substantially the same amount and kind of surface cold working with residual stresses varying over a wide range of values. It was found that shotpeening of steel of this hardness is beneficial primarily because of the nature of the macro-residual-stresses introduced by the process. There is no gain attributable to “strain-hardening” for this material. An effort was made to explain the results on the basis of three failure criteria: distortion energy, maximum shear stress, and maximum stress.*

PEARLITIC malleable iron crankshafts are being used in the new Pontiac engine as a result of recent developments. This paper discusses the physical properties of pearlitic malleable iron such as elastic modulus, fatigue endurance, and tensile strength. According to the author, definite machining economies result from using pearlitic malleable iron crankshafts.

North American drivers particularly dislike wheel dust (brake dust on their wheels). For some vehicle lines, customer surveys indicate that wheel dust is a significant concern. For this reason, Ford and its suppliers are investigating the root causes of brake dust and developing test procedures to detect wheel dust issues up-front. Intuitively, it would appear that more brake wear would lead to more wheel dust. To test this hypothesis, a gage was needed to quantitatively measure the wheel dust. Gages such as colorimeters were evaluated to measure the brightness (L*) of the wheel, which ranged from roughly 70-80% (clean) to 10-20% (very dirty). Gage R&R's and subjective ratings by a panel of 30 people were used to validate the wheel dust gages. A city traffic vehicle test and an urban dynamometer procedure were run to compare the level of wheel dust for 10 different lining types on the same vehicle.

Weld lines occur when melt flow fronts meet during the injection molding of plastic parts. It is important to investigate the weld line because the weld line area can induce potential failure of structural application. In this paper, a weld line factor (W-L factor) was adopted to describe the strength reduction to the ultimate strength due to the appearance of weld line. There were two engineering thermoplastics involved in this study, including one neat PP and one of talc filled PP plastics. The experimental design was used to investigate four main injection molding parameters (melt temperature, mold temperature, injection speed and packing pressure). Both the tensile bar samples with/without weld lines were molded at each process settings. The sample strength was obtained by the tensile tests under two levels of testing speed (5mm/min and 200mm/min) and testing temperatures (room temperature and -30°C). The results showed that different materials had various values of W-L factor.

Four multigrade engine oils, containing the same base oil plus SE additive package but VI improvers of differing shear stability, were evaluated in 80 000 km of high-speed, high-temperature vehicle service. Bearing, piston ring and valve guide wear, as well as oil consumption, oil filter plugging and engine cleanliness were all worse for the engines operated on the low-shear stability oils. The wear differences were traced to differences in high-shear-rate viscosity, while the cleanliness, filter plugging and oil consumption differences occurred because of excessive wear or polymer shear degradation. These results suggest that engine oil viscosity should be specified under high-shear-rate conditions.

Metal cutting/machining is a widely used manufacturing process for producing high-precision parts at a low cost and with high throughput. In the automotive industry, engine components such as cylinder heads or engine blocks are all manufactured using such processes. Despite its cost benefits, manufacturers often face the problem of machining chips and cutting oil residue remaining on the finished surface or falling into the internal cavities after machining operations, and these wastes can be very difficult to clean. While part cleaning/washing equipment suppliers often claim that their washers have superior performance, determining the washing efficiency is challenging without means to visualize the water flow. In this paper, a virtual engineering methodology using particle-based CFD is developed to address the issue of metal chip cleanliness resulting from engine component machining operations. This methodology comprises two simulation methods.

Vehicle chassis mounted cantilevered components should meet two critical design targets: 1) NVH criterion to avoid resonance with road noise and engine vibration and 2) satisfied durability performance to avoid any incident in structure failure and dysfunction. Generally, two types of testing are performed to validate chassis mounted cantilevered component in the design process: shaker table testing and vehicle proving ground testing. Shaker table testing is a powered vibration endurance test performed with load input summarized from real proving ground data and accurate enough to replicate the physical test. The proving ground test is typically performed at critical milestones with full vehicles. Most tests are simplified lab testing to save cost and effort. CAE procedures that virtually replicate these lab tests is even more helpful in the design verification stages.

A vehicle integrated sensing and analysis system has been designed, implemented, and demonstrated to nonintrusively monitor several biological signals of the driver. The biological driver signals measured by the system are the heart electrical signals or pseudo Lead-I electrocardiography (pLI-ECG), the galvanic skin response (GSR) or electrical conductance measured from the driver's fingers to palm, the palm skin temperature, the face skin temperature, and the respiration rate. The pLI-ECG and GSR measurements are made through direct contact of the driver hands with stainless steel electrodes integrated in the steering wheel rim. The temperature measurements are made with non-contacting infrared temperature sensors, also located on the steering wheel. The respiration rate was measured using a flexible thin film piezoelectric sensor affixed to the seatbelt.

The strain-life approach is now commonly used for fatigue life analysis and predictions in the ground vehicle industry. This approach requires the use of material properties obtained from strain-controlled uniaxial fatigue tests. These properties include fatigue strength coefficient (σf′), fatigue strength exponent (b), fatigue ductility coefficient (εf′), fatigue ductility exponent (c), cyclic strength coefficient (K′), and cyclic strain hardening exponent (n′). To obtain the aforementioned properties for the material, raw data from stable cyclic stress-strain loops are fitted in log-log scale. These data include total, elastic and plastic strain amplitudes, stress amplitude, and fatigue life. Values of the low cycle fatigue properties (σf′, b, εf′, c) determined from the raw data depend on the method of measurement and fitting. This paper examines the merits and influence of using different measurement and fitting methods on the obtained properties.

Vehicle idle quality has become an increasing quality concern for automobile manufacturers because of its impact on customer satisfaction. There are two factors that critical to vehicle idle quality, the engine excitation force and vehicle sensitivity (transfer function). To better understand the contribution to the idle quality from these two factors and carry out well-planned improvement measures, a quick and easy way to measure vehicle sensitivity at idle conditions is desired. There are several different ways to get vehicle sensitivity at idle conditions. A typical way is to use CAE. One of the biggest advantages using CAE is that it can separate vehicle sensitivities to different forcing inputs. As always, the CAE results need to be validated before being fully utilized. Another way to get vehicle sensitivity is through impact test using impact hammer or shaker. However this method doesn't include the mount preload due to engine firing torque [3, 4, & 5].

Accurate prediction of engine combustion characteristics, especially burn rates, can eliminate a number of hardware iterations, thus resulting in a significant reduction in design and developmental time and cost. An analytical methodology has been developed which allows the determination of part-load MBT spark timing to within 2 crank-angle degrees. The design methodology employs the in-house-developed steady-state quasi-dimensional engine simulation model (GESIM), coupled with full-field measurement of the in-cylinder fluid motion at bottom dead center (BDC) in the computer-controlled water analog system (AquaDyne). The in-cylinder flow-field measurements are obtained using 3-D Particle Tracking Velocimetry (3-D PTV), also developed in-house. In this methodology, the in-cylinder flow measurement data are used to calibrate both the tumble and swirl models in GESIM.

Advancing intake valve timing shortly after engine crank and run-up can potentially reduce vehicle cold start hydrocarbon (HC) emissions in port fuel injected (PFI) engines equipped with intake variable cam timing (iVCT). Due to the cold metal temperatures, there can be significant accumulation of liquid fuel in the intake system and in the cylinder. This accumulation of liquid fuel provides potential sources for unburned hydrocarbons (HCs). Since the entire vehicle exhaust system is cold, the catalyst will not mitigate the release of unburned HCs. By advancing the intake valve timing and increasing valve overlap, liquid fuel vaporization in the intake system is enhanced thereby increasing the amount of burnable fuel in the cylinder. This increase in burnable HCs must be countered by a reduction in injector-delivered fuel via a compensator that reacts to cam movement.

For suspension systems, fatigue and strength simulations are accomplished mostly at the component level. However, the selection of loading conditions and replication of boundary conditions at the component level may be difficult. A system level simulation eliminates most of the discrepancy between component level and vehicle level environment yielding realistic results. Further advantage of system level simulation is that the boundary conditions are limited to suspension mounting points at body or frame and the loading is limited to wheel-end or tire patch loading. This provides for a robust set of boundary constraints that are known and repeatable, and loads that are simpler and of relatively higher accuracy. Here, the nonlinear transient dynamic behavior of a suspension system along with its frame and mounting was simulated using a multibody finite element analysis (FEA).

The measured drive-point conductance of a typical passenger car tire was seen to drop steadily for frequencies above 1000 Hz. This behavior is a-typical since SEA theory predicts such conductance should remain relatively flat for high frequencies. It was found that, one has to pay careful attention to errors introduced by the added mass of the measuring transducer and “local” effects due to contact stiffness of the tread rubber. Such effects are investigated and their contributions quantified. Compensation schemes are also developed and implemented. It is shown that, for a 20 grams transducer, the measured and corrected conductances are off by 12 dB. The effects of the local contact stiffness of the rubber at the attachment point are less significant.

Modern approaches for thermal fatigue damage assessment in automotive components are discussed. Three prominent methods are reviewed, and issues with related material testing, numerical implementations and applications to general thermal cycles are presented. In summary, the chosen methods can produce good thermal fatigue life predictions. Common difficulties include first, prolonged experimental programs to determine the required material parameters, and second, significant computational times involved in analysis of realistic models and loading histories.

Thermal fatigue presents a new challenge in cast aluminum engine design. Accurate thermomechanical stress analysis and reliable failure criterion are the keys to a successful life prediction. It is shown that the material stress and strain behavior of cast aluminum is strongly temperature and strain rate sensitive. A unified viscoplasticity constitutive relation is thus proposed to simultaneously describe the plasticity and creep of cast aluminum components deforming at high temperatures. A fatigue failure criterion based on a damage accumulation model is introduced. Damages due to mechanical fatigue, environmental impact and creep are accounted for. The material stress and strain model and thermal fatigue model are shown to be effective in accurately capturing features of thermal fatigue by simulating a component thermal fatigue test using 3D FEA with ABAQUS and comparing the results with measured data.

The use of nanotechnology to develop advanced heat-transfer materials is a rapidly growing topic of research at facilities around the world. One class of these materials, nanofluids, has shown promise in the laboratory to dramatically improve thermal conductivity. Quantification of the thermophysical properties of these fluids is important for optimizing the design of automotive powertrains and electrical subsystems in order to produce highly efficient and robust vehicle cooling. A new technique for measuring thermal conductivity, the Transient Planar Source (TPS) method, was used for the first time to investigate the thermal conductivity of automotive coolants and their equivalent nanofluid, as a function of temperature. The results of this study indicate that the TPS method allows for rapid and repeatable measurement of thermal conductivity with an error of between 2-4%. The technique also presents several advantages over other methods which we will briefly describe.

On current competitive scenario for road load transportation in Brazilian market, the operational costs should be reduced as much as possible. The suspension system commonly used on road commercial trucks is based on leaf spring use and Hotchkiss concept for axle locating devices. The use of leaf springs without bolt attachment eyelets are still common for rear suspension systems. When using the leaf spring with direct contact to the brackets, wear plates are placed between them to work as wear elements due to the friction between the parts. The friction will cause wear on the parts, and the wear plate is designed to suffer the damages of this friction instead of the leaf spring, being the cheapest element and can be easily replaced. When the system works on a severe contamination environment with high levels of grit and dirt, the degradation of the parts are accelerated.

Acoustic standing waves are excited in internal combustion chambers by both normal combustion and autoignition. The energy in these acoustic modes can be transmitted through the engine block and radiated as high-frequency engine noise. Using finite-element models of two different (four-valve and two-valve) production engine combustion chambers, the mode shapes and relative frequencies of the in-cylinder volume acoustic modes are calculated as a function of crank angle. The model is validated by comparison to spectrograms of experimental time-sampled waveforms (from flush-mounted cylinder pressure sensors and accelerometers) from these two typical production spark-ignited engines.