Search Results

Plug-in Hybrid Electric Vehicles (PHEVs) use electric energy from the grid rather than fuel energy for most short trips, therefore drastically reducing fuel consumption. Different configurations can be used for PHEVs. In this study, the parallel pre-transmission, series, and power-split configurations were compared by using global optimization. The latter allows a fair comparison among different powertrains. Each vehicle was operated optimally to ensure that the results would not be biased by non-optimally tuned or designed controllers. All vehicles were sized to have a similar all-electric range (AER), performance, and towing capacity. Several driving cycles and distances were used. The advantages of each powertrain are discussed.

The salient features of modern gasoline direct injection include cavitation, flash boiling, and plume/plume interaction, depending on the operating conditions. These complex phenomena make the prediction of the spray behavior particularly difficult. The present investigation combines mass-based experimental diagnostics with an advanced, in-house modeling capability in order to provide a multi-faceted study of the Engine Combustion Network’s Spray G injector. First, x-ray tomography is used to distinguish the actual injector geometry from the nominal geometry used in past works. The actual geometry is used as the basis of multidimensional CFD simulations which are compared to x-ray radiography measurements for validation under cold conditions. The influence of nozzle diameter and corner radius are of particular interest. Next, the model is used to simulate flash-boiling conditions, in order to understand how the cold flow behavior corresponds to flashing performance.

Connectivity and automation provide the potential to use information about the environment and future driving to minimize energy consumption. Aerodynamic drag can also be reduced by close-gap platooning using information from vehicle-to-vehicle communications. In order to achieve these goals, the designers of control strategies need to simulate a wide range of driving situations in which vehicles interact with other vehicles and the infrastructure in a closed-loop fashion. RoadRunner is a new model-based system engineering platform based on Autonomie software, which can collectively provide the necessary tools to predict energy consumption for various driving decisions and scenarios such as car-following, free-flow, or eco-approach driving, and thereby can help in developing control algorithms.

In the past, there was little need for changes in machinery design specifically for surface mining. However, the requirements imposed by land reclamation legislation since the 1940s present problems that cannot be handled readily by conventional equipment. For the long run, new types of equipment should be considered. In the meantime, research efforts should be devoted to redesigning, enlarging, or modifying existing equipment.

Disposal of automobile shredder residue (ASR), remaining from the reclamation of steel from junked automobiles, promises to be an increasing environmental and economic concern. Argonne National Laboratory (ANL) is investigating alternative technology for recovering value from ASR while also, it is hoped, lessening landfill disposal concerns. Of the ASR total, some 20% by weight consists of plastics. Preliminary work at ANL is being directed toward developing a protocol, both mechanical and chemical (solvent dissolution), to separate and recover polyurethane foam and the major thermoplastic fraction from ASR. Feasibility has been demonstrated in laboratory-size equipment.

Cavitation plays an important role in fuel injection systems. It alters the nozzle's internal flow structure and discharge coefficient, and also contributes to injector wear. Quantitatively measuring and mapping the cavitation vapor distribution in a fuel injector is difficult, as cavitation occurs on very short time and length scales. Optical measurements of transparent model nozzles can indicate the morphology of large-scale cavitation, but are generally limited by the substantial amount of scattering that occurs between vapor and liquid phases. These limitations can be overcome with x-ray diagnostics, as x-rays refract, scatter and absorb much more weakly from phase interfaces. Here, we present an overview of some recent developments in quantitative x-ray diagnostics for cavitating flows. Measurements were conducted at the Advanced Photon Source at Argonne National Laboratory, using a submerged plastic test nozzle.

Recent advancements in x-ray radiography diagnostics for direct injection sprays at Argonne's Advanced Photon Source have allowed absorption measurements of individual spray events, in addition to ensemble-averaged measurements. These measurements offer insight into the shot-to-shot variation of these sprays in the near-nozzle, spray formation region. Three single hole diesel injectors are studied across various injection and ambient pressures, spanning 14 different conditions. We calculated two dimensional maps of the standard deviation in line of sight mass distribution between individual spray events. These illuminated the spatial and temporal extent of variability between spray events. Regions of large fluctuations were observed to move downstream during the initial spray period and reached a steady state location after this initial transient.

This paper presents the energy savings of an automated driving control applied to an electric vehicle based on the on-track testing results. The control is a universal speed planner that analytically solves the eco-driving optimal control problem, within a receding horizon framework and coupled with trajectory tracking lower-level controls. The automated eco-driving control can take advantage of signal phase and timing (SPaT) provided by approaching traffic lights via vehicle-to-infrastructure (V2I) communications. At each time step, the controller calculates the accelerator and brake pedal position (APP/BPP) based on the current state of the vehicle and the current and future information about the surrounding environment (e.g., speed limits, traffic light phase).

This work has explored the preliminary design of a Computational Fluid Dynamics (CFD) tool for the analysis of transient vehicle underhood thermo-hydrodynamic events using high performance computing platforms. The goal of this tool will be to extend the capabilities of an existing established CFD code, STAR-CD [1], allowing the car manufacturers to analyze the impact of transient operational events on the underhood thermal management by exploiting the computational efficiency of modern high performance computing systems. In particular, the project has focused on the CFD modeling of the radiator behavior during a specified transient. The 3-D radiator calculations were performed using STAR-CD, which can perform both steady-state and transient calculations on one of the cluster computers available at Argonne National Laboratory. Specified transient boundary conditions, based on experimental data provided by Adapco and DaimlerChrysler were used.

A simulation approach is defined that integrates a military mission assessment tool (One Semi-Automated Forces) with a commercial automotive control/energy consumption development tool (Autonomie). The objective is to enable vehicle energy utilization and fuel consumption impact assessments relative to US Army mission effectiveness and commercial drive cycles. The approach to this integration will be described, along with its potential to meet its objectives.

A multimode transmission combines several power-split modes and possibly several fixed gear modes, thanks to complex arrangements of planetary gearsets, clutches and electric motors. Coupled to a battery, it can be used in a highly flexible hybrid configuration, which is especially practical for larger cars. The Chevrolet Tahoe Hybrid is the first light-duty vehicle featuring such a system. This paper introduces the use of a high-level vehicle controller based on instantaneous optimization to select the most appropriate mode for minimizing fuel consumption under a broad range of vehicle operating conditions. The control uses partial optimization: the engine ON/OFF and the battery power demand regulating the battery state-of-charge are decided by a rule-based logic; the transmission mode as well as the operating points are chosen by an instantaneous optimization module that aims at minimizing the fuel consumption at each time step.

Argonne National Laboratory (ANL), working with the Partnership for a New Generation of Vehicles (PNGV), maintains hybrid vehicle simulation software: the PNGV System Analysis Toolkit (PSAT). The importance of component models and the complexity involved in setting up optimized control strategies require validation of the models and controls developed in PSAT. Using ANL's Advanced Powertrain Test Facilities (APTF), more than 50 tests on the Honda Insight were used to validate the PSAT drivetrain configuration. Extensive instrumentation, including the half-shaft torque sensor, provides the data needed for through comparison of model results and test data. In this paper, we will first describe the process and the type of test used to validate the models. Then we will explain the tuning of the simulated vehicle control strategy, based on the analysis of the differences between test and simulation.

This paper introduces an eco-driving highway cruising algorithm based on optimal control theory that is applied to a conventionally-powered connected and automated vehicle. Thanks to connectivity to the cloud and/or to infrastructure, speed limit and slope along the future route can be known with accuracy. This can in turn be used to compute the control variable trajectory that will minimize energy consumption without significantly impacting travel time. Automated driving is necessary to the implementation of this concept, because the chosen control variables (e.g., torque and gear) impact vehicle speed. An optimal control problem is built up where quadratic models are used for the powertrain. The optimization is solved by applying Pontryagin’s minimum principle, which reduces the problem to the minimization of a cost function with parameters called co-states.

In recent studies, optimal control has shown promise as a strategy for enhancing the energy efficiency of connected autonomous vehicles. To maximize optimization performance, it is important to accurately predict constraints, especially separation from a vehicle in front. This paper proposes a novel prediction method for forecasting the trajectory of the nearest preceding car. The proposed predictor is designed to produce short to medium-length speed trajectories using a locally weighted polynomial regression algorithm. The polynomial coefficients are trained by using two types of information: (1) vehicle-to-vehicle (V2V) messages transmitted by multiple preceding vehicles and (2) vehicle-to-infrastructure (V2I) information broadcast by roadside equipment. The predictor’s performance was tested in a multi-vehicle traffic simulation platform, RoadRunner, previously developed by Argonne National Laboratory.

Fan and fan-shroud design is critical for underhood air flow management. The objective of this work is to demonstrate a method to optimize fan-shroud shape in order to maximize cooling air mass flow rates through the heat exchangers using the Adjoint Solver in STAR-CCM+®. Such techniques using Computational Fluid Dynamics (CFD) analysis enable the automotive/transport industry to reduce the number of costly experiments that they perform. This work presents the use of CFD as a simulation tool to investigate and assess the various factors that can affect the vehicle thermal performance. In heavy-duty trucks, the cooling package includes heat exchangers, fan-shroud, and fan. In this work, the STAR-CCM+® solver was selected and a java macro built to run the primal flow and the Adjoint solutions sequentially in an automated fashion.

In order to improve understanding of the primary atomization process for diesel-like sprays, a collaborative experimental and computational study was focused on the near-nozzle spray structure for the Engine Combustion Network (ECN) Spray D single-hole injector. These results were presented at the 5th Workshop of the ECN in Detroit, Michigan. Application of x-ray diagnostics to the Spray D standard cold condition enabled quantification of distributions of mass, phase interfacial area, and droplet size in the near-nozzle region from 0.1 to 14 mm from the nozzle exit. Using these data, several modeling frameworks, from Lagrangian-Eulerian to Eulerian-Eulerian and from Reynolds-Averaged Navier-Stokes (RANS) to Direct Numerical Simulation (DNS), were assessed in their ability to capture and explain experimentally observed spray details. Due to its computational efficiency, the Lagrangian-Eulerian approach was able to provide spray predictions across a broad range of conditions.

This research investigates the energy savings achieved through eco-driving controls in connected and automated vehicles (CAVs), with a specific focus on the influence of powertrain characteristics. Eco-driving strategies have emerged as a promising approach to enhance efficiency and reduce environmental impact in CAVs. However, uncertainty remains about how the optimal strategy developed for a specific CAV applies to CAVs with different powertrain technologies, particularly concerning energy aspects. To address this gap, on-track demonstrations were conducted using a Chrysler Pacifica CAV equipped with an internal combustion engine (ICE), advanced sensors, and vehicle-to-infrastructure (V2I) communication systems, compared with another CAV, a previously studied Chevrolet Bolt electric vehicle (EV) equipped with an electric motor and battery.

Development of computationally fast, numerically robust, and physically accurate models to compute engine-out emissions can play an important role in the design, development, and optimization of automotive engines powered by alternative fuels (such as natural gas and H2) and fuel blends (such as ethanol-blended fuels and biodiesel-blended fuels). Detailed multidimensional models that couple fluid dynamics and chemical kinetics place stringent demands on the computational resources and time, precluding their use in design and parametric studies. This work describes the development of an integrated design tool that couples a fast, robust, physics-based, two-zone quasi-dimensional engine model with modified reaction-rate-controlled models to compute engine-out NO and CO for a wide variety of fuel-additive blends.

Design and optimization of automotive engines present unique challenges on account of the large design space and conflicting constraints. A notable example of such a problem is optimizing the fuel consumption and reducing emissions over the drive cycle of an automotive engine. There are over twenty design variables (including operating conditions and geometry) for the above-mentioned problem. Conducting design, analyses, and optimization studies over such a large parametric space presents a serious computational challenge. The large design parameter space precludes the use of detailed numerical or experimental investigations. Physics-based reduced-order models can be used effectively in the design and optimization of such problems.

This paper discusses the development of an integrated tool for the design, optimization, and real-time control of engines from a performance and emissions standpoint. Our objectives are threefold: (1) develop a tool that computes the engine performance and emissions on the order of a typical engine cycle (25-50 milliseconds); (2) enable the use of the tool for a wide variety of engine geometries, operating conditions, and fuels with minimal user changes; and (3) couple the engine module to an efficient optimization module to enable real-time control and optimization. The design tool consists of two coupled modules: an engine module and an optimization module.