Search Results

The selection of a motor for a windshield wiper system requires a full analysis of all system variables, in addition to strict adherence to tests and development procedures. Following a well-programmed procedure will assure complete and adequate windshield wiper prime mover selection and successful application. There are five basic steps discussed: 1. Determination of wiper parameters. 2. Motor performance. 3. System load determination. 4. Calibration and matching of wiper motor to system. 5. Testing and evaluating.

The Kinematic Analysis Methods Computer Program that has been used by Ford Motor Co. to evaluate mechanisms for the past four years has been modified to generate performance curves for windshield wiper linkages directly using a Calcomp Plotter. Problems such as stalling, “jerky” operation, and excessive phase lag between wipers can be detected early in the design stages by careful evaluation of the curves.

Automotive outside rear view mirror shape has become an important consideration in achieving wind noise and aerodynamic performance objectives. This paper describes a two step process used to develop a mirror shape which meets both wind noise and aerodynamic objectives. First, basic understanding of door mounted verses sail mounted mirrors and shape parameters was obtained by evaluating selected shapes and studying their physical measurements relative to their measured responses. Relationships between the wind noise and drag responses revealed performance range limitations for sail mounted mirrors. Second, a central composite experimental design was utilized to more closely investigate door mounted mirror shape parameters to determine optimal mirror performance potential. The resulting empirical models developed were used to determine the best overall solution.

This paper outlines the key elements in a laboratory reliability verification test program for an automotive sub-system. Many of these elements are described in some detail through the various stages of development from prototype concept to production. By means of an actual case study, verification testing of the 1970 Ford Anti-Theft Steering Column, steps required to design tests which yield meaningful information and the rationale used to analyze the results are presented. The steering column on a late model automobile is a complex system which combines several functions and features; steering, shifting, warning devices (turn signal and emergency flashers), ignition switch, anti-theft devices plus several safety features. The effectiveness of the overall verification program is evaluated through the presentation of actual field-feedback results.

This study is a joint development project between Chrysler Corporation and CFD Research Corporation. The objective of this investigation was to develop a 3D computational flow and heat transfer model for a vehicle windshield de-icing process. The windshield clearing process is a 3D transient, multi-medium, multi-phase heat exchange phenomenon in connection with the air flow distribution in the passenger compartment. The transient windshield de-icing analysis employed conjugate heat transfer methodology and enthalpy method to simulate the velocity distribution near the windshield inside surface, and the time progression of ice-melting pattern on the windshield outside surface. The comparison between the computed results and measured data showed very reasonable agreement, which demonstrated that the developed analysis tool is capable of simulating the vehicle cold room de-icing tests.

One of the major goals in the design of the new Ford Aeromax and Louisville heavy truck product line was to achieve competitive leadership in visibility. Market research found that visibility was an important issue to the heavy truck driver. Visibility is defined as both direct and indirect (i.e., the driver's ability to see with and without the use of supplemental vision devices such as mirrors) and both interior and exterior. The scope of this paper includes the work which was accomplished in evaluating direct and indirect exterior visibility and the resulting vehicle design which achieved Ford's leadership goals. Poor weather visibility and interior vision are beyond the scope of this paper. Polar Plots were the method of choice in the Aeromax/Louisville visibility studies. Industry acceptance of these techniques has been established in the recent approval of SAE J1750, “Evaluating the Truck Driver's Viewing Environment”.

Properties of thermoplastic bumpers made of polycarbonate (PC) and polybutylene terephthalate (PBT) blend were evaluated after several years of service in the field. In this study we measured the Izod impact strength, PC molecular weight, and melt flow rate of bumpers collected from various geographical areas in the U.S. Generally, the system had good impact resistance after more than five years of service in the field, retaining most of the original impact strength. There were small changes in PC average molecular-weights and melt flow rates. The results showed that changes depended on both exposure time and the weather conditions of the environment.

The impingement of air jets on a vehicle's windshield is one parameter that determines the effectiveness of the defroster's system in freeing the windshield of frost and fog. Incompressible air jets impinge upon the inner surface of the windshield and create hydrodynamic and thermal boundary layers which in turn control convective heat transfer. Therefore, understanding the heat transfer interaction between impinging air jets and an inclined windshield is of practical relevance. Experimental investigations on the temperature distribution are performed on the inner surface of the windshield for the purpose of obtaining local and average heat transfer coefficients. In this paper, the temperature distribution of a vehicle's windshield is investigated using liquid crystals. As a result, a temperature contour map is generated displaying local temperature values on the inner surface of the windshield.

Different approaches have been proposed in the past for designing smooth complex reflectors. One major difficulty in designing headlamps with smooth reflectors is maintaining the slope continuity of the reflector surface without compromising the robustness of the beam pattern. In this paper, two simple algorithms are proposed for developing smooth complex reflector headlamps. The first is a numerical marching scheme used to generate smooth complex surfaces based on user specified spread points. In the second approach, a parametrically represented smooth surface is generated with user defined spread points to obtain the desired beam patterns.

In an attempt to predict the responses of side crash pressure sensors, the Corpuscular Particle Method (CPM) was adopted and enhanced in this research. Acceleration-based crash sensors have traditionally been used extensively in automotive industry to determine the air bag firing time in the event of a vehicle accident. The prediction of crash pulses obtained from the acceleration-based crash sensors by using computer simulations has been very challenging due to the high frequency and noisy responses obtained from the sensors, especially those installed in crash zones. As a result, the sensor algorithm developments for acceleration-based sensors are largely based on prototype testing. With the latest advancement in the crash sensor technology, side crash pressure sensors have emerged recently and are gradually replacing acceleration-based sensor for side impact applications.

With the increasing demand to improve recyclability of automobiles worldwide the Vehicle Recycling Partnership (VRP) a cooperative effort among Chrysler, Ford and General Motors has been formed. The VRP has been developing preferred practices for improvement of recyclability for future vehicle subsystems. These preferred practices are intended to assist engineers and designers in improving recyclability without impairing the performance of the subsystem. This paper discusses the practices of specific design for recycling of plastic bumper fascia systems and what the designer should consider in developing a design to improve and maximize recyclability.

Automotive use of thermoplastic polymers has grown significantly within the last 10 years. At the same time that societal environmental expectations have increased and resulted in greater demand for the recycling of all materials. Efforts in recycling continue to be explored among the automotive community in planning for the recycling of the plastics being used in current products. Automotive manufacturers and their raw material suppliers are investigating technologies and processes that create the opportunity to produce viable outlets for recycled materials into both their original and other applications. The success of these efforts encouraged the investigation and development of a process to recycle post consumer bumpers as well.

To understand how the passenger compartment cavity interacts with the surrounding panels (roof, windshield, dash panel, etc) a numerical panel contribution analysis was performed using FEA and BEA techniques. An experimental panel contribution analysis was conducted by Reiter Automotive Systems. Test results showed good correlation with the simulation results. After gaining some insight into panel contributions for power train noise, an attempt was made to introduce beads in panels to reduce vibration levels. A fully trimmed body structural-acoustic FEA model was used in this analysis. A network of massless beam elements was created in the model. This full structural-acoustic FEA model was then used to determine the optimal location for the beads, using the added beams as optimization variables.

Door weather strip seals are designed with ventilation holes spaced at regular intervals along the seal system to expedite the flow of air from the seal system during the door closing process. The flow of air through the ventilation holes represents a nonlinear damping mechanism which, depending upon hole size and spacing, can significantly contribute to door closing effort. In this study we develop one- and two- dimensional versions of a nonlinear damping model for seal compression load deflection (CLD) behavior which incorporate the effects of seal damping response due to air flow through the ventilation holes. The air flow/damping models are developed from first physical principles by application of the mass and momentum balance equations to a control volume of entrapped air between consecutive air ventilation holes in the seal system.

A new type of thin film light source has been developed. It's most interesting feature is voltage control of the emission color. The underlying physical principles give new insight into light producing mechanisms.

A search for methods of switching a proposed three beam headlight system led to the evaluation of 41 possible schemes. Human factors criteria reduced the original 41 to three systems which were tested in a laboratory with a broad range of subjects. Recordings of practice trials, learning trials, and the responses to visual cues projected on a screen were analyzed. The same test procedure was also used to compare three alternative ways of switching conventional two beam headlight systems. Summary data is presented for the six systems tested grouped by test subject age, sex, and driving experience. The most pronounced difference observed was in the subjective preference rating among two beam switching systems. All systems tested resulted in remarkably few learning and practice trials. Small differences were recorded among systems in operational response time.

The headlamp beam pattern development process contains both subjective and objective evaluations. The subjective evaluation, communication between the customer and the engineer, was developed in previous work [1][2]. This paper presents exploratory models used in the identification of objective photometric variables of a beam pattern that relate to the subjective impression of the beam pattern. Additional research will allow use of the photometric variables and their selected ranges for designing and evaluating beam patterns to achieve improved customer pleasing beam pattern driving experiences.

The method of communication between the customer and the engineer has been refined to further improve the headlight beam pattern development process. The refinements included: a) reduction of word pairs used for semantic differential scaling and b) use of shortened questionnaire on night-roadway viewing zones. The added benefit of the new questionnaire method allows the engineer to evaluate the customer responses of the beam pattern within specific areas on the road scene. A statistical technique called factor analysis has been used to evaluate and to reduce the large number of semantic differential word pairs used in the previous work by Jack, O'Day and Bhise (1). A comparison of the two questionnaire forms used in the evaluation surveys was completed based on an evaluation of beam patterns in a dynamic drive situation.

A method for communication linking the vehicle user and the lighting engineer has been developed to improve the headlight beam pattern development process. A technique called the semantic differential has been used to quantify the user's perception on a large number of attributes of the beam pattern. The basis of the technique utilizes descriptive words used by both drivers and engineers to characterize headlight beam patterns. Beam pattern evaluations conducted in a series of dynamic drive situations formed the initial data base. Subsequent evaluations using this technique have facilitated close and quick interaction between the customer and the engineer during the development of headlight beam patterns.

This paper presents a new computerized approach for designing the automobile window glass contour, the glass drop motion, and the regulator systems. The three-dimensional geometrical relationship of the glass contour, the drop path, and its guidance system have been studied. Methods for barrel and helical drops are presented for optimizing the glass profile and drop path trajectories. Criteria for perfecting the glass contour are developed for shaping the profile of the vehicle clay model. Methods for correcting the glass contour and shape are presented. Examples are provided to illustrate how to improve the design. This approach integrates the development works of glass contour, drop motion and regulator systems. Through this design approach the window glass can fit and move perfectly in the door assembly.