Search Results

British Aerospace needed an automated wing riveting system for fastening the A320 wing sections. The E4000 Wing Riveting System was designed and installed at their Airbus factory in Chester, UK and is now in production. It uses a five axis solid yoke with workheads on each end of the yoke. It accurately installs both rivets and lockbolts over the entire wing panel, including offset areas.

The use of paint automation in commercial aircraft production is being studied to reduce process cycle times, provide a higher quality paint finish, lower emissions, and increase process consistency. The cost of new aircraft paint hangars and increasing production rates is driving a need for increased capacity in existing facilities by using new coatings and technology. Testing of robotic painting at Boeing has uncovered unique differences between aerospace and automotive applications. Paint cure times, number of paint colors, environment control, and part size considerations are some of the issues that make aerospace application of coatings more difficult than automotive applications. Understanding the unique factors involved in the robotic application of commercial aerospace coatings is important for future advancements in application technology, gains in aircraft paint hangar capacity, delivering quality coating finishes, and lowering environmental footprint.

An automated machine has been designed with true offset fastening to join shear-tie/frame assemblies to the fuselage of the Boeing 787 Dreamliner. The machine can access fasteners located close to structural components that are very deep. This is accomplished by offsetting the fastening axis from the axis of the head for true offset fastening. The head can be positioned next to the structural component and the offset fastening tooling ‘reaches’ out to the fastener location (Figure 1). By using a true offset, the fastening machine can access fasteners that would be otherwise inaccessible by traditional automated equipment. The machine can also be lighter and more accurate when compared to fastening machines with traditional tooling.

As a result of recommendation from the Augustine Panel, the direction for Human Space Flight has been altered from the original plan referred to as Constellation. NASA's Human Exploration Framework Team (HEFT) proposes the use of a Shuttle Derived Heavy Lift Launch Vehicle (SDLV) and an Orion derived spacecraft (salvaged from Constellation) to support a new flexible direction for space exploration. The SDLV must be developed within an environment of a constrained budget and a preferred fast development schedule. Thus, it has been proposed to utilize existing assets from the Shuttle Program to speed development at a lower cost. These existing assets should not only include structures such as external tanks or solid rockets, but also the Flight Software which has traditionally been a ?long pole? in new development efforts. The avionics and software for the Space Shuttle was primarily developed in the 70's and considered state of the art for that time.

Electroimpact has developed a new Fastener Feed System which provides an automated solution for fasteners previously hand fed via drop tubes. The hardware is simple, compact, and is supplied a fraction of the cost of hoppers or cartridges. It can be used as a primary feed system or it can be used as an auxiliary feed system when combined with feed systems designed for high quantities of fasteners. We have installed this system on the A380 Stage 0 LVER lower panel wing machines and feed 5 diameters, 10 grips each, for a total of 50 different fastener types. This system moves 547 total fasteners per ship set from manual feed to automatic feed, saving considerable build time.

Boeing's wholly owned subsidiary in Australia, Hawker de Havilland produces all ailerons for the Boeing 737 family of aircraft. Increasing production rates required to meet market demand drove the requirements for a new updated approach to assembly of these parts. Using lean principals, a pulsed flow line approach was developed. A component of this new line is the integration of a flexible robotic drilling/trimming system. The new robotic system is required to meet aggressive tack time targets with high levels of reliability. The selected system was built on a Kuka KR360-2 conventional articulated arm robot. A significant challenge of this project was the requirement for the process head to work efficiently on an aileron in an existing jig. As a result a new side-mounted drill and trim end effector was developed. Automated tool changers for both cutters and pressure foot assemblies eliminated the requirement for in- process manual intervention.

Robotic gripper technology has been integrated into CNC riveting machines. Handling fasteners efficiently is critical in automated wing panel riveting. Computer controlled rivet gripper and collar gripper technology has been developed that demonstrates high reliability and decreased fastener cycle times

Flex Track Drilling systems have been successfully implemented into several production environments and scenarios over the past couple of years. They continue to see a high demand where traditional machine tool implementations might be prohibitive due to cost or existing jig structures. This demand for innovation has led to a unique Flex Track design termed an Offset Flex Track that not only works between the vacuum rails, but can work beyond the envelope of the rails. This allows the machine to be used in situations such as the leading edge of wings where the vacuum rails cannot straddle the work envelope. The next evolution of this Offset machine is the introduction of final fastener installation onto the head using an onboard rivet gun. In addition, the camera used to locate datum points on the fuselage is now integrated into the nose piece, eliminating the need for a tool change to a spindle mounted camera.

New fastener feeding approaches are compared with existing bowl feeders and hoppers. A “smart” hopper for headed fasteners and slug rivets combines a fastener sensor with robust mechanics. The coiled tube magazine system uses briefcase sized magazines with integral escapements. These magazines can handle slugs or headed fasteners. For slug rivets, a magazine based system uses off-line loading to eliminate system slow-down due to debris or bulk fastener problems. A system for collars and nuts can feed various fasteners down a flexible tube to the installation point, requiring ten seconds to change fasteners.

Equipment used in aerospace non-destructive inspection presents opportunity for modernization. Many inspection cells in production operate using a widely available control system software that is suitable for most inspection applications with minimal customization. The size and complex geometry of airframe components demand more application-specific system design to ensure the reliability and cycle time required for an aerospace production schedule. Ordinary inspection systems require manual teaching for program generation and lack datum-finding systems required to rerun programs without modification. Integration of offline programming software and machine vision instruments can save inspection technicians hours or shifts per part by eliminating the need for program retraining due to variation in part delivery position. Modernized inspection cells will reduce labor burden on technicians and provide reliable cycle time information to production planners.

Wing skin riveting and bolting requires the surface to be flush to +/–.025mm(.001″) to produce an acceptable finish. Using the method described in this paper, automated wing riveting technology and panel assembly techniques can achieve better shave height and countersink accuracies than have previously been possible in production.

British Aerospace, Airbus Ltd., Chester, UK manufactures the main wing box assembly for all current Airbus programs. Titanium interference fasteners are used in large numbers throughout these aircraft structures. On the lower wing skin of the A320 alone there are approximately 11,000 of this fastener type. Currently, the majority of these fasteners are manually installed using pneumatic or hydraulic tooling. British Aerospace engineers recognized the significant potential which automation offers to reduce these current labor intensive installation methods. Electroimpact proposed extending Low Voltage Electromagnetic Riveter (LVER) technology to the automatic installation of these interference fasteners as well as rivets. Close liaison between Airbus and Electroimpact engineers resulted in the development of an automated LVER based lockbolt installation system, which is currently undergoing evaluation.

This paper gives an outline of testing carried out in conjunction with Electroimpact to support the introduction of the A319/A320/A321 and A340-500/600 Panel Assembly Cells in Broughton, UK. Testing compared the percussion insert/EMR swaging of lockbolts with existing hydraulic installation methods. Tests included pre-load tension tests, ultimate tension load tests, tension fatigue tests, high-load lap shear fatigue tests, static lap shear tests, a pressure leak test, and metallurgical examination. Fastener configurations tested covered diameters from 1/4, 5/16, 3/8, and 7/16 of an inch. Joint materials conformed to ABM3-1031 (7150-T651 plate), stump-type lockbolts to ABS0550VHK (Huck LGPS4SCV), and collars to ASNA2025 (Huck 3SLC-C). Some pull-type lockbolts to ABS0548VHK (Huck LGPL4SCV) were also tested as noted.

Hand installation of 3/8", 5/16" and 1/4" diameter fatigue head style fasteners is required on some areas of 747 section 11 (center wing). The 3/8" diameter fasteners can require between 45-60 seconds to upset using conventional pneumatic riveting guns. As part of Boeing’s continuing effort to reduce cycle time and improve the factory working environment, a Boeing Quality Circle Team proposed using LVER technology as an alternative to conventional pneumatic percussion riveting hammers The hand operated HH500 system was developed in response to this request. The HH500 single shot upset reduces installation time as well as the noise levels and vibration experienced by the operators. The design of this system and the integration onto the factory floor are presented. The LVER forming rate is significantly higher than that of conventional pneumatic and hydraulic processes.

The Automated Fiber Placement (AFP) machine layup run time in large scale AFP layup cells consumes approximately 30% of the entire part build time. Consequentially, further reductions to the run time of the AFP machine part programs result in small improvements to the overall cycle time. This document discusses how Electroimpact's integrated system and cell design reduces the overall cycle time by reducing the time spent on non-machine processes.

Through the use of an “Integrated Product Team” approach and new inspection techniques incorporating the latest in imaging capabilities and automation, the costs of some man-power intensive tasks can now be drastically reduced. Also, through the use of advanced eddy current techniques, the detectable size of cracks under flush-head fasteners can be reduced while maintaining reliable inspection. This article describes the evaluation and results obtained using eddy current technology to determine the minimum fasteners, Secondly, it describes the integrated efforts of engineers at Boeing DPD and Northwest Airlines in the successful application of MAUS eddy current scanning of the DC-10 circumferential and axial crow splices. The eddy current scanning greatly reduced the man-hour effort required for the existing radiographic inspection

A new wing panel riveting cell capable of replacing tack fasteners and performing small repair jobs has been developed. Using two mobile scissor lift platforms with electromagnetic riveters mounted on each, the operators can access every portion of the wing panel without the use of ladders or platforms. This method minimizes fatigue, allows workers to carry all tools and supplies with them, meets current safety standards and minimizes coldworking of the components.

Large diameter, tightly toleranced fastener patterns are commonplace in aerospace structures. Satisfactory generation of these holes is often challenging and can be further complicated by difficult or obstructed access. Bespoke tooling and drill jigs are typically used in conjunction with power feed units leading to a manual, inflexible, and expensive manufacturing process. For 777X flap production, Boeing and Electroimpact collaborated to create a novel, automated solution to generate the fastener holes for the main carrier fitting attachment pattern. Existing robotic automation used for skin to substructure assembly was modified to utilize extended length (up to 635mm), bearing-supported drill bar sub-assemblies. These Long Assembly Drills (LADs) had to be easily attached and detached by one operator, interface with the existing spindle(s), supply cutting lubricant, extract swarf on demand, and include a means for automatically locating datum features.

Automated Fiber Placement (AFP) equipment has been developed capable of laying fiber in excess of 2000 inches per minute on full-size, complex parts. Two such high-speed machines will be installed for production of a nose section for a large twin-aisle commercial aircraft fuselage at Spirit AeroSystems in Wichita, Kansas along with a rotator for the fuselage mandrel. The problem of cutting and adding on the fly at these speeds requires thorough re-evaluation of all aspects of the technology, including the mechanical, controls, servos systems, and programming systems. Factors to be considered for high speed cut and add on the fly are discussed.

The Boeing 787 Dreamliner will be the most fuel-efficient airliner in the world when it enters service in 2008. To help achieve this, Boeing will utilize state-of-the-art carbon fiber for primary structures. Advanced manufacturing techniques and processes will be used in the assembly of large composite structures. Electroimpact has proposed a system utilizing the low recoil Low Voltage Electromagnetic Riveter (LVER) to drill and install bolts. A test program was initiated between Boeing Materials Process and Engineering (MP&E) and Electroimpact to validate the LVER process for swaging titanium collars on titanium pins in composite material. This paper details the results of these tests.