Search Results

This active-drive wheel speed sensor, developed by the high-frequency magnetic system, enables detection of very slow wheel speeds - hitherto difficult to accomplish with any conventional type of Magnetic Pick up - by applying the eddy current effect through the high-frequency magnetic field. The following report presents an analysis of the magnetic circuit which integrates the magnetic-field generating coil with the detection rotor, and the unique circuit system which ensures strength against eccentricity of the wheel rotor and air gap variations, etc.

This paper proposes a novel method of verifying comprehensive driver model used for the evaluation of driving safety systems, which is achieved by coupling the traffic simulation and the driving simulator (DS). The method consists of three-step procedure. In the first step, an actual driver operates a DS vehicle in the traffic flow controlled by the traffic simulation. Then in the next step, the actual driver is replaced by a driver model and the surrounding vehicle maneuvers are replayed using the recorded data from the first step. Then, the maneuver by the driver model is compared directly with the actual driver's maneuver along the simulation time steps.

To reduce interior noise effectively in the vehicle body structure development process, noise and vibration engineers have to first identify the portions of the body that have high sensitivity. Second, the necessary vibration characteristics of each portion must be determined, and third, the appropriate body structure for achieving the target performance of the vehicle must be realized within a short development timeframe. This paper proposes a new method based on the substructure synthesis method which is effective up to 200Hz. This method primarily utilizes equations expressing the relationship between driving point inertance change at arbitrary body portions and the corresponding sound pressure level (SPL) variation at the occupant's ear positions under external force. A modified system equation was derived from the body transfer functions and equation of motion by adding a virtual dynamic stiffness expression into the dynamic stiffness matrix of the vehicle.

The renewed platform of the upcoming flagship front-engine, rear-wheel drive (FR) vehicles demands high levels of driving performance, fuel efficiency and noise-vibration performance. The newly developed driveline system must balance these conflicting performance attributes by adopting new technologies. This article focuses on several technologies that were needed in order to meet the demand for noise-vibration performance and fuel efficiency. For noise-vibration performance, this article will focus on propeller shaft low frequency noise (booming noise). This noise level is determined by the propeller shaft’s excitation force and the sensitivity of differential mounting system. In regards to the propeller shaft’s excitation force, the contribution of the axial excitation force was clarified. This excitation force was decreased by adopting a double offset joint (DOJ) as the propeller shaft’s second joint and low stiffness rubber couplings as the first and third joints.

In today's motorized society, various automotive technologies continue to evolve every day. Amid this trend, a new concept with respect to automatic transaxle gear-shifting has been developed. In order to materialize a new concept for shifting operation with a universal design in mind, a system has been developed: a shift-by-wire system developed specifically for hybrid vehicles. The greatest advantage of this new system is the lack of constraints associated with the conventional mechanical linkage to the transaxle. This allows freedom of design for the gear selection module. A revolutionary improvement in the ease of shifting has been realized by taking full advantage of this design freedom. In addition, this system contributes to an innovative design. For improved ease of operation, the operation force of the shift lever of this system has been dramatically reduced. For parking, the driver can engage the parking mechanism of the transaxle at the touch of a switch.

New engine controls have been developed for the turbocharged Lexus NX200t to improve driving power by reducing engine torque output lag. Drive power management functions have been centralized in an integrated drive power control system. The newly developed controls minimize the potential reduction in drivability associated with the adoption of a turbocharged engine while improving fuel efficiency. General driveability issues commonly associated with a turbocharged engine include sudden increases in drive power due to the response lag of the turbocharger, and higher shifting frequencies if this response lag triggers a disturbed accelerator operation pattern by the driver. The developed technologies detect and control sudden increases in drive power to create the optimum drive power map, and reduce unnecessary shifts even if the driver's accelerator operation is disturbed.

Recently, automobile features designed to improve maneuverability and convenience are being improved. However, many drivers still have difficulty with parking maneuvers. Although parking is unavoidable for drivers, yet ranks third among the most difficult driving situations for Japanese drivers. Drivers in other countries also consider parking to be difficult and even skill drivers would appreciate some assistance. Therefore, a parking support system has been developed to reduce the workload for all drivers while also improving parking performance. The parking support system Human-Machine Interface (HMI) operation should be designed to easy to use for best performance. The back-in perpendicular parking performance of drivers with different skill levels was studied to see the effect of the parking support system. Back-in perpendicular parking is the major parking method in Japan.

Compatibility in vehicles crashes has been studied worldwide in recent years. In cases where primary energy-absorbing structures such as front end members were bypassed in front-to-front collisions, energy-absorbing efficiency declined compared to cases when no such bypassing occurred. A bumper beam that connects the front end members in the transverse direction can help prevent bypassing of primary energy-absorbing structures. The strength balance between front end members and a bumper beam was studied in this paper. It was verified in front-to-front offset vehicle collision tests that crash energy can be efficiently absorbed by balancing the strength of the bumper beam with the compression strength of the front end members.

The purpose of this study is to propose braking characteristics that are easy for drivers to handle in a system in which braking and driving operations are performed by hand. Genetic algorithm optimization of braking characteristics showed that the best deceleration tracking was achieved by an FG diagram with a logarithmic function shape. In contrast, the slope of the optimal FG diagram tended to decrease as the driver's proportional gain increased.

This study aims at the development of a projection pattern that is capable of shortening the time required by a driver to perceive a pedestrian at night when a vehicle’s high beams are utilized. Our approach is based on the spatio-temporal frequency characteristics of human vision. Visual contrast sensitivity is dependent on spatiotemporal frequency, and maximum contrast sensitivity frequency varies depending on environmental luminance. Conventionally, there are several applications that utilize the spatio-temporal frequency characteristics of human vision. For example, the National Television System Committee (NTSC) television format takes into consideration low-sensitivity visual characteristics. In contrast, our approach utilizes high-sensitivity visual characteristics based on the assumption that the higher contrast sensitivity of spatio-temporal frequencies will correlate more effectively with shorter perception times.

Replacing the metal car roof with conventional solar modules results in the increase of total car weight and change of center of mass, which is not preferable for car designing. Therefore, weight reduction is required for solar modules to be equipped on vehicles. Exchanging glass to plastic for the cover plate of solar module is one of the major approaches to reduce weight; however, load bearing property, impact resistance, thermal deformation, and weatherability become new challenges. In this paper a new solar module structure that weighs as light as conventional steel car roofs, resolving these challenges is proposed.

We investigated a lighting method that supports pedestrian perception by vehicle drivers. This lighting method makes active use of visual characteristics such as the spatio-temporal frequency of contrast sensitivity. Using reasonable parameter values derived from preliminary experiments using a Campbell-Robson chart, we determined a suitable lighting pattern that improves the driver's pedestrian perception. In order to assess the influence of visual characteristics on a reaction-time-dependent task, such as pedestrian perception in nighttime, tests were performed in the target environment, the results of which validated the proposed method.

The metal top is used for convertible cars since the exterior design when the rooftop is closed is also important. A retractable metal top system which can automatically retract and extract the metal top has been popular to increase commercial values for the luxury convertible cars. We have developed the metal top open-close system comprising metal top,package tray and luggage panel operation link-mechanism units driven by electric motors. The metal top can be retracted or extracted in approximately 25 seconds by controlling the metal top system and the side and quarter window motors. The roof panel is pre-load so that the cabin air-tightness for high speed driving is maintained. The metal top is compactly retracted since the slide and side package trays are synchronized. Enough luggage space is secured using the multi-link mechanism to open and close the luggage panel. This retractable metal top system is equipped with the LEXUS SC430. (Fig.1) [1]

This paper describes impact kinematics and injury values of Hybrid III AM50, THOR AM50 and THUMS AM50 in simulated oblique frontal impact conditions. A comparison was made among them in driver and passenger seat positions of a midsize sedan car finite element (FE) model. The simulation results indicated that the impact kinematics of THOR was close to that of THUMS compared to that of the Hybrid III. Both THOR and THUMS showed z-axis rotation of the rib cage, while Hybrid III did not. It was considered that the rib cage rotation was due primarily to the oblique impact but was allowed by flexibility of the lumbar spine in THOR and THUMS. Lateral head displacement observed in both THOR and THUMS was mostly induced by that rotation in both driver seat and passenger seat positions. The BrIC, thorax and abdominal injury values were close to each other between THOR and THUMS, while HIC15 and Acetabulum force values were different.

A newly developed parking assist system, which is based on rear view camera, is disclosed. System features include ‘parallel parking aid’ with voice guidance message along with several guidelines superimposed onto the rear view camera image. Voice guide message helps driver understand appropriate timing for each procedure of parallel parking. The system was designed to let driver follow the system by voice message rather than visual guide information through the screen for safety reason. The guide algorism is designed under ‘two turns’ parking maneuvers so that required longitudinal parking space becomes minimal. A key development of this system, which is to design the guide algorism to avoid collision to adjacent vehicle during parallel parking operation, is also discussed in this paper. User can select either ‘parallel guide’ or ‘normal (such as garage parking)’ mode through touch screen switch on display surface.

Toyota Safety Sense is a safety system package developed to help drivers avoid accident types with a high frequency of occurrence. This paper deals with pre-collision system which forms the core of Toyota Safety Sense, especially Toyota Safety Sense P which uses a combined sensor configuration consisting of a monocular camera paired with millimeter wave radar, in order to achieve both high recognition performance and reliability. The use of a wide-angle monocular camera, millimeter wave radar integrated in the front grill emblem, and a collision determination algorithm for pedestrian targets enabled the development of a pre-collision system comprising detection capability of crossing pedestrians. Toyota has developed warning and pre-collision brake assist for driver to assist in avoiding a collision effectively; In addition, Pre-collision brake has achieved high level of performance for the drivers who cannot avoid a collision.

Underbody coating is used to prevent chipping damage of the automobile underbody and wheel well. Multi-functional material that gives sound insulating properties is called sound insulating underbody coating. This paper describes the development of underbody coating material with powdered acrylic composition as an alternative to polyvinyl chloride resin. The new material also has better foaming properties. It is possible to ensure excellent sound insulating performance with thin film. This multi-functional underbody coating is the first application in the world with weight reduction and cost saving, and in a more environmentally acceptable manner.

Toyota Motor Corporation has developed a new drivetrain for their flagship Lexus LFA sports car. Passionate driving experience was pursued at the forefront of development. Superior vehicle performance, handling, and responsiveness that seem to anticipate the driver's intentions are achieved. Special vehicle packaging and component placement are adopted in the LFA in order to realize such performance. The engine, clutch, and front counter gear are positioned at the front of the vehicle, and the transaxle at the rear. The engine and transaxle are connected by a rigid torque tube. The transaxle is an automated manual transmission equipped with an electrohydraulic actuator for controlling both the shift and clutch operations. This actuator enables accurate control of the transmission and extremely quick response to shift paddle operation by the driver. This paper describes a general outline of the drivetrain and each component that has significantly contributed to LFA product appeal.

In order to cope with the increases of the consciousness of safety driving and the aged drivers, AISIN SEIKI CO., LTD. and TOYOTA MOTOR CORPORATION have aimed at improvements in rear view visibility of outside mirrors running under the raining conditions (water cleaning), and have developed mirror with water cleaning device utilizing ultra sonic vibrations. The mirror was named as ULTRA SONIC VIBRATING MIRROR and have been installed with a TOYOTA flagship car “CELSIOR” corresponding to “LEXUS” sold in the U.S.

Through a polymer design and precise morphology control, The Super Olefin Polymer, TSOP-1 and TSOP-5 were developed for the material consolidation of interior and exterior parts, respectively. Due to a good balance of TSOP performance, several conventional materials were consolidated into one material for each application. Accordingly, considerable amounts of weight reduction and cost savings have been obtained. In addition to the excellent recyclability of TSOP, the coated bumpers collected from the market were re-utilized through paint decomposition technology. The first dashboard construction, molded partially with foam-padded skin, was also realized. The current amount of TSOP used in a vehicle is about 30% of the total amount of plastic materials. Through the usage of TSOP, 70% of the material consolidation has been achieved.