Search Results

Clutches are commonly utilised in passenger type and off-road heavy-duty vehicles to disconnect the engine from the driveline and other parasitic loads. In off-road heavy-duty vehicles, along with fuel efficiency start-up functionality at extended ambient conditions, such as low temperature and intake absolute pressure are crucial. Off-road vehicle manufacturers can overcome the parasitic loads in these conditions by oversizing the engine. Caterpillar Inc. as the pioneer in off-road technology has developed a novel clutch design to allow for engine downsizing while vehicle’s performance is not affected. The tribological behaviour of the clutch will be crucial to start engagement promptly and reach the maximum clutch capacity in the shortest possible time and smoothest way in terms of dynamics. A multi-body dynamics model of the clutch system is developed in MSC ADAMS. The flywheel is introducing the same speed and torque as the engine (represents the engine input to the clutch).

A hybrid electric vehicle simulation tool (IBZ-Simulator) has been developed at the Fuel Cell Institute of the University of Applied Sciences Esslingen to study the fuel economy potential of a Fuel Cell hybrid urban bus. In this paper, the fundamental architecture of the FC urban buses was described, as well as the control strategy to manage the power flow between the different elements of the drive train. A comparison of the hybrid with the conventional type and ICE-hybrid type is performed, and important factors relating to the vehicle efficiency (accessory loads, vehicle mass, Fuel Cell system ramping rate and battery capacity) were assessed. The using of supercapacitor (or ultracapacitors) as peak power buffer has been investigated.

This paper features an application study on the impact of different blend levels of commercially-supplied biodiesel on engine and aftertreatment systems' durability and reliability as well as the impact on owning and operating factors: service intervals and fuel economy. The study was conducted on a bus application with a 2007 on highway emissions equipped engine running biodiesel blends of B5, B20, and B99 for a total period approaching 4500 hours. Biodiesel of waste cooking grease feedstock was used for the majority of the testing, including B5 and B20 blends. Biodiesel of soybean feedstock was used for testing on B99 blend. No negative impacts on engine and aftertreatment performance and durability or indication of future potential issues were found when using B5 and B20. For B99 measurable impacts on engine and aftertreatment performance and owning and operating cost were observed.

Electronics technology has evolved significantly since the first electronically controlled heavy duty on-highway truck engines were introduced in the mid 1980's. Engine control hardware, software, and sensor designs have been driven by many factors. Emissions regulations, fuel economy, engine performance, operator features, fleet management information, diagnostics, vehicle integration, reliability, and new electronics technology are some of those factors. The latest engine electronics technology is not only found in heavy duty on-highway trucks, but in off-highway applications as well. Track-type tractors, haul trucks, wheel loaders, and agricultural tractors now benefit from the advantages of electronic engines. And, many more new applications are being developed.

A cooperative program between the DOE Office of Heavy Vehicle Technology and Caterpillar is aimed at demonstrating electric turbo compound technology on a Class 8 truck engine. The goal is to demonstrate the level of fuel efficiency improvement attainable with an electric turbocompound system. The system consists of a turbocharger with an electric motor/generator integrated into the turbo shaft. The generator extracts surplus power at the turbine, and the electricity it produces is used to run a motor mounted on the engine crankshaft, recovering otherwise wasted energy in the exhaust gases. The electric turbocompound system also provides more control flexibility in that the amount of power extracted can be varied. This allows for control of engine boost and thus air/fuel ratio. The paper presents the status of development of an electric turbocompound system for a Caterpillar heavy-duty on-highway truck engine.

Improved fuel economy and reduction of emissions can be achieved by insulation of the combustion chamber components to reduce heat rejection. However, such insulation will also increase the operating temperature of the piston ring/cylinder liner interface from approximately 150°C to over 300°C. Since existing ring/liner materials cannot withstand these higher operating temperatures alternatives are needed for this critical tribological interface. This paper describes the development of a cost effective ID grinding technique for machining the bores of plasma sprayed diesel engine cylinder liners.

Various engine platforms employ Selective Catalytic Reduction (SCR) technology to reduce the tail pipe emissions of oxides of nitrogen (NOx) from diesel engines as part of an overall strategy to comply with the emission regulations in place in various countries. High levels of NOx conversion (greater than 98%) in SCR aftertreatment may provide operating margin to increase overall fuel efficiency. However, to realize the potential fuel efficiency gains, the SCR technology employed should achieve high NOx conversion with limited reductant slip over transient application cycles in addition to steady state operation. A new approach to SCR controls was developed and implemented. This approach does not rely on any maps to determine the amount of urea solution to be dosed, thus significantly reducing calibration and development time and effort when implementing the SCR technology on multiple engine platforms and applications.

Maximum fuel economy and Low exhaust emissions can exist together if a predominantly wide-open-throttle engine operating schedule is used to complement a continuously variable transmission. Moreover, the concurrently required engine re-calibration often entails less effort than the more usual fuel consumption and emission mapping procedure.

Fuel is a significant portion of the operating cost for an on-highway diesel engine and fuel economy is important to the economics of shipping most goods in North America. Cat® ACERT™ engine technology is no exception. Ball bearings have been applied to the series turbochargers for the Caterpillar heavy-duty, on-highway diesel truck engines in order to reduce mechanical loss for improved efficiency and lower fuel consumption. Over many years of turbocharger development, much effort has been put into improving the aerodynamic efficiency of the compressor and turbine stages. Over the same span of time, the mechanical bearing losses of a turbocharger have not experienced a significant reduction in power consumption. Most turbochargers continue to use conventional hydrodynamic radial and thrust bearings to support the rotor. While these conventional bearings provide a low cost solution, they do create significant mechanical loss.

Driving cycles have been used in Federal Test Procedures to establish fuel economy and emissions characteristics for automobiles. Reasonable driving cycles for trucks and buses have been more difficult to establish because of the great variety of uses which these vehicles experience. The truck cycle has been divided into three different use categories—the local cycle, the short haul cycle, and the highway cycle. Only recently, has actual field data been obtained, and this paper proposes a method of utilizing this data to develop a more realistic local cycle than those previously proposed.

The U.S. Department of Energy (DOE) and the U.S. automotive industry are collaborating on research and development of advanced compression ignition direct injection (CIDI) engine technology and polymer electrolyte membrane (PEM) fuel cells for automotive applications. Under the auspices of the Partnership for a New Generation of Vehicles (PNGV), the partners are developing technologies to power an automobile that can achieve up to 80 miles per gallon (mpg), while meeting customer needs and all safety and emissions requirements. Research on enabling technologies for CIDI engines is focusing on advanced emissions control to meet the proposed stringent Environmental Protection Agency emissions standards for oxides of nitrogen (NOx) and particulate matter (PM) in 2004, while retaining the high efficiency and other traditional advantages of CIDI engines.