Search Results

Many different studies have been performed to understand brake roughness, and in particular how brake rotor Disc Thickness Variation (DTV) is generated. The intent of this paper is to analytically explore through non- linear finite element modeling methods the effects of wheel joint variables on brake rotor mounted Lateral RunOut (LRO). The phenomenon of LRO is believed to be a primary contributor to DTV generation and resulting brake roughness. CAE analyses were conducted in non-linear contact mechanics in which real contacts between components exist. Various joint designs were simulated to compare rotor LRO and coning. Several parameters inherent to the design of wheel joints were varied and studied. A comparative approach was used to develop specific design recommendations for LRO reductions.

A data processing algorithm is presented for determining the spatial orientation and position of a rigid body in impact tests based on an instrumentation scheme consisting of a triaxial angular rate sensor and a trialaxial linear accelerometer. The algorithm adopts the unit quaternion as the main parameterized representation of the spatial orientation, and calculates its time history by solving an ordinary differential equation with the angular rate sensor reading as the input. Two supplemental representations, the Euler angles and the direction cosine matrix, are also used in this work, which provide an intuitive description of the orientation, and convenience in transforming the linear accelerometer output in the instrumentation frame to the global frame. The algorithm has been implemented as a computer program, and a set of example impact tests are included to demonstrate its application.

During initial phases of vehicle development process, it is usually required to understand the temperature profile for all components. It is usually more effective and less costly if the thermal issues are determined and addressed before actual vehicles are built. Computational Fluid Dynamics (CFD) analysis tools are typically used for thermal management of the vehicle environment. However, for transient thermal analysis problems, running a full CFD requires solving the mass, momentum, and energy equations. This typically requires a lengthy computation time and extensive computer resources. The problem becomes more challenging when trying to conduct CFD analysis for several design iterations and for different duty cycles that may be of a transient nature. Therefore, the application of one-dimensional analysis early in the development phase can help point out the areas of prime concern.

Ethanol is widely used as a gasoline component to provide a prescribed amount of oxygenates and for its perceived advantages of less dependence on petroleum based products and lowering overall CO2 emissions. In most cases the level of ethanol in gasoline does not exceed 10%. In some parts of the Unites States, E85 fuel consisting of 85% ethanol and 15% gasoline is commonly available. Many US vehicles sold today are specially adapted for use of both gasoline and high ethanol fuels; so-called Flexible Fuel Vehicles (FFV). While high ethanol fuels are currently a small percentage of the overall gasoline pool, they provide an interesting opportunity to study the effects that ethanol use in gasoline may have on lubricant related performance. Based on past industry experience with methanol based fuel, theoretical areas of concern for ethanol based fuels are valve train rust and potential problems associated with high amounts of water in the lubricant.

A D.C. permanent magnet motor powered fan can serve as a cooling package air flow meter. This allows for continuous air flow monitoring during vehicle operation with applications to more precise air flow control schemes. In the freewheel mode, the air flow is a linear function of the open circuit voltage of the motor. In the powered mode, the motor voltage and current can be used with a motor and fan model to predict fan air flow. The model is explained and verifying test results are presented. Comparison of the accuracy and complexity vs. that of arrays of precision anemometers is provided.

A correlation study was performed between static wind tunnel testing and computational fluid dynamics (CFD) for a small hatchback vehicle, with the intent of evaluating a variety of different wheel and tire designs for aerodynamic forces. This was the first step of a broader study to develop a tool for assessing wheel and tire designs with real world (rolling road) conditions. It was discovered that better correlation could be achieved when actual tire scan data was used versus traditional smooth (CAD) tire geometry. This paper details the process involved in achieving the best correlation of the CFD prediction with experimental results, and describes the steps taken to include the most accurate geometry possible, including photogrammetry scans of an actual tire that was tested, and the level of meshing detail utilized to capture the fluid effects of the tire detail.

The Chrysler Ultradrive four-speed transaxle 41TE was the first production transmission to pioneer fully adaptive direct clutch-to-clutch electronic controls without overrunning clutches. "Single stage" high flow PWM solenoids have been used for transmission control since 1989 and still being used in the later-developed 545RFE and 62TE transmissions. The proposed target volume-based shift control method allows the usage of flow-based control device such as PWM solenoids to implement torque-based control strategy. Vehicle test results with this new method have shown excellent shift quality and improved system consistency.

An automotive cockpit module is a complex assembly, which consists of components and sub-systems. The critical systems in the cockpit module are the instrument panel (IP), the floor console, and door trim assemblies, which consist of many plastic trims. Stiffness is one of the most important parameters for the plastic trims' design, and it should be optimum to meet all the three functional requirements of safety, vibration and durability. This paper presents how the CAE application and various other techniques are used efficiently to predict the stiffness, and the strength of automotive cockpit systems, which will reduce the product development cycle time and cost. The implicit solver is used for the most of the stiffness analysis, and the explicit techniques are used in highly non-linear situations. This paper also shows the correlations of the CAE results and the physical test results, which will give more confidence in product design and reduce the cost of prototype testing.

The intake and exhaust port design plays a substantial role in performance of combustion systems. The port design determines the volumetric efficiency and in-cylinder charge motion of the spark-ignited engine which influences the thermodynamic properties directly related to the power output, emissions, fuel consumption and NVH properties. Thus intake port has to be appropriately designed to fulfill the required charge motion and high flow performance. While turbulence intensity and air-mixture quality affect dilution tolerance and fuel economy as a result, breathing ability affects wide open throttle performance. Traditional approaches require experimental techniques to reach a target balance between the charge motion and breathing capacity. Such techniques do not necessarily result in an optimized solution.

This paper highlights a simplified CAE model technique, which can simulate and predict door crush strength performance quickly. Such quick models can be used for DFSS and Design change studies. The proposed method suggests an equivalent sub model technique using only the door beam with tuned stiffness end springs to predict FMVSS214S full vehicle crush performance. Such models can be solved in minutes and hence very useful for DFSS studies during product design. The proposed method can be used to finalize door beam design for identical size of vehicle doors to meet required FMVSS214S crush performance. The paper highlights the door beam end springs tuning for identical size of cars and SUVs. Four vehicles were considered for the study. A single spring F-D (force -displacement) is tuned which correlated well for frond door of all the four vehicles. A separate unique spring F-D was needed which correlated well for rear door of all the 4 vehicles.

Under the initiative of the United States Council for Automotive Research LLC (USCAR§) Transmission Working Group, a collaborative effort was made with LuK USA LLC to study the influence of the friction interface parameters on the shudder durability of a wet launch clutch. Clutch configurations with different combinations of four friction materials (A, B, C and D), three groove patterns (waffle, radial and waffle-parallel) and two separator plate conditions (nitrided and non-nitrided) were considered. Durability testing consisted of a test profile, with 110 kJ energy per test cycle, developed earlier in this project. Materials A, B and C with nitrided separator plates reached the end of test criteria for the torque gradient and showed shudder. Materials B and C were more wear resistant as compared to materials A and D. The loss of friction coefficient (μ) was lower for materials B, C and D as compared to material A.

Under the initiative of the United States Council for Automotive Research LLC (USCAR§) Transmission Working Group, a collaborative effort was made with LuK USA LLC to study the influence of the friction interface parameters on the shudder durability of a wet launch clutch. A test bench was designed. Clutch configurations with different combinations of four friction materials (A, B, C and D), three groove patterns (waffle, radial and waffle–parallel) and two separator plate conditions (nitrided and non–nitrided) were considered. Considerable improvement in performance was seen by changing from CVT fluid* to DCT fluid*. A thermal analysis based on thermal model predictions and measurement correlations was conducted. Comparisons of clutch configurations with four and five friction plates were done. The waffle and radial groove pattern showed better heat transfer than the waffle–parallel groove pattern.

Nitrocarburizing is an economical surface hardening process and is proposed as an alternative heat treatment method to carbonitriding. The focus of this study is to compare the size and shape distortion and residual stresses resulting from the ferritic nitrocarburizing and gas carbonitriding processes for SAE 1010 plain carbon steel. Gas, ion and vacuum nitrocarburizing processes utilizing different heat treatment temperatures and times were performed to compare the different ferritic nitrocarburizing processes. Navy C-Ring specimens and prototype stamped parts were used to evaluate size and shape distortion. X-ray diffraction techniques were used to determine the residual stresses in the specimens. Overall, the test results indicate that the nitrocarburizing process gives rise to smaller dimensional changes than carbonitriding, and that the size and shape distortion can be considerably reduced by applying appropriate ferritic nitrocarburizing procedures.

The door closing effort is a quality issue concerning both automobile designers and customers. This paper describes an Excel based mathematical model for predicting the side door closing effort in terms of the required minimum energy or velocity, to close the door from a small open position when the check-link ceases to function. A simplified but comprehensive model is developed which includes the cabin pressure (air bind), seal compression, door weight, latch effort, and hinge friction effects. The flexibility of the door and car body is ignored. Because the model simplification introduces errors, we calibrate it using measured data. Calibration is also necessary because some input parameters are difficult to obtain directly. In this work, we provide the option to calibrate the hinge model, the latch model, the seal compression model, and the air bind model. The door weight effect is geometrically exact, and does not need calibration.

External aerodynamic simulations are becoming more important because of regulatory pressures on fuel economy improvements and shorter design cycles. Experimental work is typically done on scaled models to get drag and cooling flow information. This is a time consuming process. Numerical simulations might provide a complementary path to get the answers in a timely manner. This paper discusses one such approach.

Ring gear bolts in differentials are often modified in size to accommodate the additional clamp load that is required due to an increase in torque from a vehicle's powertrain. Depending on a given program several constraints need to be considered. These include cost, validation time, reliability / durability and timing for implementation. In this paper, a Finite Element Analysis (FEA) procedure for analyzing stresses in ring gear bolts within a rear differential assembly is outlined and the computational results are then compared to quasi-static bench test results that were developed to measure bending and tension loads in the ring gear bolts during loading and unloading of the axle pinion. A dynamometer test is then developed to duplicate the failure mode and provide a comparison of the design changes proposed and the expected improvement in durability.

The Sarbanes-Oxley Act created new standards for corporate accountability pertaining to all publicly-owned and traded firms. It holds top executives accountable for the accuracy of all financial data and statements, including reported tangible assets. It requires existence of auditable internal accounting control measures and specifies adherence to new internal controls and procedures designed to ensure the validity of their financial records and physical assets. The Act presents a challenge to every manufacturing firm to have a low-cost system implemented that can produce an exact physical-asset location, existence, verification and accounting on demand. Clearly, such low-cost solutions for enterprise-wide compliance would also provide verifiable and reliable data for corporate property tax, loan collateral, and audit requirements.

SAE 8620 and other steels are typically used in the carburized condition for powertrain applications in the automotive industry, i.e., differential ring gears, camshafts, and transmission gears. Although current recommended carburizing practice involves normalizing the steel prior to carburizing, elimination of this normalizing treatment could lead to significant cost reductions. This research examines whether the normalizing process prior to carburizing could be eliminated without negatively affecting part performance. This study focused on the effects of the initial microstructure on the residual stress, retained austenite, and effective case depths of carburized SAE 8620 and PS-18 steels.

This paper presents the studies on how to efficiently and easily implement ECU application algorithms using the Signal Processing Engine (SPE) of the Copperhead microcontroller. With the introduced development and testing concepts and methods, users can easily establish their own PC based SPE emulation system. All application unit testing and verification work for the fixed point implementation using SPE functions can be easily conducted in PC without relying on a costly real time test bench and expensive third party dedicated software. With this simple development environment, the code can be run in both embedded controllers and PCs with exact bit to bit numerical behavior. The paper also demonstrates many other benefits such as code statistics information retrieval, floating simulation mode, automated code verification, online and offline code sharing.

Magnesium alloy extrusions offer potentially more mass saving compared to magnesium castings. One of the tasks in the United States Automotive Materials Partnership (USAMP) ?Magnesium Front End Research and Development? (MFERD) project is to evaluate magnesium extrusion alloys AM30, AZ31 and AZ61 for automotive body applications. Solid and hollow sections were made by lowcost direct extrusion process. Mechanical properties in tension and compression were tested in extrusion, transverse and 45 degree directions. The tensile properties of the extrusion alloys in the extrusion direction are generally higher than those of conventional die cast alloys. However, significant tension-compression asymmetry and plastic anisotropy need to be understood and captured in the component design.