Search Results

The Cummins A3.4-125 (rated 93 kW at 3600 rpm) has been developed to meet 1991 US and California light-heavy duty emission standards, replacing the Cummins 6AT3.4 (formerly Onan L634T-A). Compliance with the stringent particulate standard has been achieved by redesigning the combustion chamber, a systematic oil control program, and charge air cooling. The Ricardo Comet combustion chamber was modified to a downstream glowplug configuration. Oil control efforts addressed all sources of oil derived particulate. With charge air cooling, NOx emissions were reduced while improving fuel economy, torque output, altitude capability, and engine durability. THE CUMMINS A3.4-125 is an evolutionary development of the 1988-90 6AT3.4 engine. The development was driven primarily by 1991 US and California light-heavy duty emission standards, but also was the result of a policy of continuous product improvement. The Cummins A Series diesel engine family was conceived as the Onan L Series (1*).

This paper discusses the goals, progress, and future plans of the TACOM/Cummins Adiabatic Engine Program. The Adiabatic Engine concept insulates the diesel combustion chamber with high temperature materials to allow hot operation near an adiabatic operation condition. Additional power and improved efficiency derived from this concept occur because thermal energy, normally lost to the cooling and exhaust systems, is converted to useful power through the use of turbomachinery and high-temperature materials. Engine testing has repeatedly demonstrated the Adiabatic Engine to be the most fuel efficient engine in the world with multi-cylinder engine performance levels of 0.285 LB/BHP-HR (48% thermal efficiency) at 450 HP representative. Installation of an early version of the Adiabatic Engine within a military 5 ton truck has been completed, with initial vehicle evaluation successfully accomplished.

The ongoing need for improved fuel economy, longer engine life, lower emissions, and in some cases, increased power output makes lower charge air temperatures more desirable. In 1983, Cummins introduced the new BCIV engine at 400 H.P. (298 KW) with “Optimized Aftercooling”, and is now introducing this concept to its remaining 10 and 14 Litre premium diesel engines. This Tuned Low Flow Cooling design provides many advantages when compared to the other alternatives studied, which included air-to-air and systems incorporating two radiators. The selection process considered performance, durability, fuel economy, emissions, noise, investment, and total vehicle installed cost. Computer simulations and vehicle tests were used to determine performance for each charge air cooling alternative. The simulations were used to guide prototype development and the selection of production hardware.

A laboratory method has been developed to rank the scuff resistance of piston ring coatings. This method employs a standard wear test apparatus with a specially designed sample holder. Scuff resistance of electrolytic chrome, thermal spray and physical vapor deposition (PVD) face coatings have been examined. Based on this method, examined PVD coatings produced the highest scuff resistance of all the tested face coatings.

Laboratory tests have shown that 40% glass-reinforced PPS is suitable for automotive underhood use where it comes into contact with used engine oil, gasoline/alcohol, gasoline/MTBE, water, water/ethylene glycol, hydraulic fluid, and transmission fluid at elevated temperatures. On exposure to water or water/ethylene glycol at 248° F (120° C) and 257°F (125°C), respectively, there is a sharp decline in mechanical strength in the first few weeks with little change thereafter. The residual strength of the 40% glass-reinforced PPS is comparable to, or better than other materials, such as phenolics, which have proved satisfactory in such usage. These results have been translated to successful applications in heavy duty diesel engines. Piston cooling nozzles and water pump impellers made of 40% glass-reinforced PPS have undergone successful engine component evaluations.

The ability of a piston oil ring to conform to liner distortions during engine operation is directly related to its radial stiffness. The ability to conform is also very important for controlling lubricant oil consumption and emissions. This paper describes the procedure utilized to investigate the technical feasibility of using flexible high performance engineering plastics to replace metal as base material for oil rings. Bench tests and engines were used to select and evaluate different types of plastics for wear resistance and structural integrity. Engine test results indicated no structural failures but wear levels were found to be unacceptably high for use in durable heavy duty diesel engines.

This paper documents the successful operation of a modified Cummins T46 turbocharger with a ceramic rotor. This turbocharger is modified to incorporate a 4.6 inch diameter ceramic turbine rotor (pressureless sintered silicon nitride) on the hot end. These results document the most complete ceramic turbine rotor performance map, for a large ceramic turbocharger rotor, available to date.

There has been an accelerated growth in power of diesel engines in United States line haul trucking. This paper analyzes the effect of high power on engine-related operating variables that occur under different highway conditions and dissimilar terrain features. When properly applied, high-powered diesel engines can increase average vehicle speed and/or fuel economy.

Measurements of instantaneous temperature were made at three locations on the cylinder head of a direct injection diesel engine. Changes in calculated instantaneous heat flux with changes in cylinder head surface temperature were assessed. The results were used in an assessment of various approaches to the description of instantaneous heat transfer incorporated in diesel cycle simulations. It was concluded that changes in the thermal boundary layer thickness throughout the cycle could account for some of the observed phenomena. A close correlation was seen between the heat transfer measured here and earlier published studies of measured boundary layer thickness. Some additional indications from the measurements point to a significant thermal capacitance of the boundary layer. Additional work is needed to further understand the potential ramifications of this effect.

High Velocity Oxygen Fuel sprayed face coatings have shown great promise for piston rings used for High Power Density Diesel Engines. Various coatings have been tested on both wear test rigs and in engines. A highly dense HVOF cermet coating was developed with reasonable crack resistance during service. The HVOF coated piston rings wore three to six times lower than chrome plating. Cylinder liner (counter face) wear was found to be one to three times higher than chrome. However, engine oil consumption and blow by were within normal values. The HVOF coating is considered to be an excellent replacement for chrome plating. The coating process is more environmentally friendly than the chrome plating process. Also, the coating has potentially lower or equivalent production cost when compared to chrome.

A number of wear resistant coatings has been developed using physical vapor deposition(PVD) process. However this coating process has not yet been widely used in the automotive industry. The purpose of this work was to evaluate thin PVD coatings such as diamond like carbon doped with tungsten (W-DLC), molybdenum-disulfide doped with aluminum (MoS2-Al), and chrome nitride (CrN). Some of these coatings were previously found to have low friction, high wear resistance, or both when tested in unlubricated conditions. In the present work, the experiments were conducted using a Cameron-Plint apparatus in lubricated conditions. The ring counterfaces used were Cr-plated and gas-nitrided compression rings. Our data also indicated that some PVD coatings with thicknesses in the same order of magnitude as the surface roughness of the liners did show some improvement in liner wear resistance. The suitability of thin coatings for liner applications needs additional study.

Tests were conducted with several production diesel engines and one prototype low-emission diesel engine to determine the effect of fuel properties on exhaust emissions and engine performance. Fuel cetane number was found to be the most significant fuel property; low cetane fuels resulted in higher hydrocarbons and oxides of nitrogen and increased noise. Conversely, higher cetane fuels produced lower emissions and noise, and also improved engine starting characteristics. The degree of these effects was influenced by engine configuration. Although engine design changes can result in substantial emissions reduction, fuel properties can also influence achieveable levels.

Diesel engine operation under high load conditions (>45 hp/cyl) may result in piston “debond” in which the Ni-resist ring carrier separates from the aluminum piston matrix leading to destruction of the piston. Historically, engine loads have increased to achieve higher power densities which together with more stringent emissions requirements have resulted in greatly increased stress levels in the piston. The higher stresses have resulted in debond failure. The design of the ring carrier will affect debond failure. Deformation of the ring carrier will initiate debond at the back of the insert at the junction with the piston matrix. The ring carrier cross-section must be made robust enough through proper design to achieve expected reliability. Another factor influencing ring carrier retention is the quality of the AlFin bond layer. Casting defects which arise from the AlFin bonding process, degrade the strength of the joint leading to failure.

This work evaluates the thermal and structural integrity of a heavy duty diesel piston using finite element analysis. The effects of aluminum, ductile iron, and superalloy piston materials; air gaps; and plasma-sprayed zirconia coating on piston temperature and stress, as well as on heat flux through the piston, are assessed. The coating lowered the heat flux through the piston 56 percent and caused other changes in the piston to have an insignificant effect on the heat flux. The air gaps had the least effect on heat flux with substantially lower safety margins than pistons without air gaps.

Evolving diesel engine design trends are expected to include fuel systems operating at significantly higher pressures and temperatures than in the past. Accordingly, meaningful laboratory tests are needed to help guide this development. Two candidate test methods were evaluated in this exploratory study. Scuffing Load Ball-on Cylinder Lubricity Evaluator (BOCLE) and Modified High-Frequency Reciprocating Rig (HFRR) test results covering a range of operating temperatures were compared with fuel property data. Correlations of the Modified HFRR test data with BOCLE results were also made.