Search Results

Current trends in vehicle development, including both automotive and commercial vehicles, are characterized by short model life cycles, reduced development time, concurrent design and manufacturing development, reduced design changes, and reduced total cost. All of these are driven by customer demand of higher load capacity, reduced weight, extended durability and warranty requirement, better NVH performance and reduced cost. These trends have resulted in increased usage of computational simulation tools in design, manufacturing, and testing, i.e. virtual testing or virtual prototyping. This paper summarizes our work in virtual testing, i.e. fatigue life simulations using computational fracture mechanics for commercial vehicle axle gearing development. First, fatigue life simulation results by using computational fracture mechanics CRACKS software were verified by comparing with gear teeth bending fatigue test data and three point bending fatigue test data.

This paper discusses the virtual development process used to support design of a high-tonnage hydroform press. It also discusses the optimized design for structural integrity while achieving low target cost. Other considerations included optimization of setup issues such as press fabrication and assembly. Due to tightly constrained development time, a diverse range of CAE methodologies were used to refine and validate the design. Detailed linear and nonlinear finite element models were developed to provide the required accuracy in the critical regions of the press structure. From these detailed models simplified analytical tools were developed to calculate the key press parameters such as alternating stress and predicted fatigue life. Finite element models were validated with physical strain gage measurements from an array of strain gages installed on the production presses.

Sound absorbing materials are commonly compressed when installed in passenger compartments or underhood applications altering the sound absorption performance of the material. However, most prior work has focused on uncompressed materials and only a few models based on poroelastic properties are available for compressed materials. Empirical models based on flow resistivity are commonly used to characterize the complex wavenumber and characteristic impedance of uncompressed sound absorbing materials from which the sound absorption can be determined. In this work, the sound absorption is measured for both uncompressed and compressed samples of fiber and foam, and the flow resistivity is curve fit using an appropriate empirical model. Following this, the flow resistivity of the material is determined as a function of the compression ratio.

Transmission loss (TL) is a good performance measure of mufflers since it represents the muffler's inherent capability of sound attenuation. There are several existing numerical methods, which have been widely used to calculate the TL from numerical simulation results, such as the four-pole and three-point methods. In this paper, a new approach is proposed to evaluate the transmission loss based on the reciprocal work identity. The proposed method does not assume plane wave propagation in the inlet and outlet ducts, and more importantly, does not explicitly apply the anechoic termination impedance at the outlet. As a result, it has the potential of extending TL computation above the plane wave cut-off frequency.

Carbon nanomaterials such as vertically aligned carbon nanotubes arrays are emerging new materials that have demonstrated superior mechanical, thermal, and electrical properties. The carbon nanomaterials have the huge potential for a wide range of vehicular applications, including lightweight and multifunctional composites, high-efficiency batteries and ultracapacitors, durable thermal coatings, etc. In order to design the carbon nanomaterials for various applications, it is very important to develop effective computational methods to model such materials and structures. The present work presents a structural mechanics approach to effectively model the mechanical behavior of vertically aligned carbon nanotube arrays. The carbon nanotube may be viewed as a geometrical space frame structure with primary bonds between any two neighboring atoms and thus can be modeled using three-dimensional beam elements.

This paper presents the criteria in selecting the size of the tuning capacitor, and the cost tradeoff between magnet volume and tuning capacitor in a free piston Stirling engine power generation system. The permissible range of capacitor size corresponding to different magnet volume, in order to prevent magnet demagnetization and stabilize the operation of the system, is determined. Within the permissible range suitable capacitor size may be selected to compensate the inductive load of the system to improve the overall power factor. If the capacitor size is not in the permissible range, there would exists a danger of losing magnet strength, or unstable operation of the engine that would destroy the engine due to unbounded amplitude of piston oscillations. The theory developed is then applied to a practical system, and the cost tradeoff between magnet volume and capacitor is studied.

Fatigue testing of components is used to validate new product designs as well as changes made to existing designs. On new designs it is common to initially test parts at the design stage (design verification or DV) and then again at the production stage (production verification or PV) to make sure the performance has not changed. On changes to existing designs typically the life of the new part (B) is compared to that of the old part (A). When comparing the fatigue life Weibull analysis is normally used to evaluate the data. The expectation is that the B10 or B50 life of the new part or PV parts should be equal to or better than that of the old parts or the DV parts. However, fatigue testing has a great deal of inherent variability in the resulting life. In this paper the variability of numerous carburized and induction hardened components is examined.

The scope of this paper is to determine the affects that non-petroleum based fuels such as: rapeseed methyl ester (RME) and soy methyl ester (SME) have on thermoset elastomers. The thermoset elastomers that have been evaluated are NBR (Nitrile Butadiene Rubber), NBR/PVC (Nitrile Butadiene Rubber & Polyvinyl Chloride), Epichlorohydrin homo- (Homopolymer of Epichlorohydrin), co- (Copolymer of Epichlorohydrin), ter- (Terpolymer of Ecpichlorohydrin), and Di-, and ter FKM (Fluorinated Rubber). The different elastomers have been subjected to aging in neat fatty acid methyl esters, RME and SME, at a variety of durations and temperatures. The effects of this exposure on the properties of thermoset elastomers are described in this paper.

One of the more useful metrics to characterize the high frequency performance of an isolator is insertion loss. Insertion loss is defined as the difference in transmitted vibration in decibels between the non-isolated and isolated cases. Insertion loss takes into account the compliance on the source and receiver sides. Accordingly, it has some advantages over transmissibility especially at higher frequencies. In the current work, the transfer matrix of a spring isolator is determined using finite element simulation. A static analysis is performed first to preload the isolator so that stress stiffening is accounted for. This is followed by modal and forced response analyses to identify the transfer matrix of the isolator. In this paper, the insertion loss of spring isolators is examined as a function of several geometric parameters including the spring diameter, wire diameter, and number of active coils.

It has been shown that the addition of a small amount of nanoparticles into a fluid results in anomalous increase in the thermal conductivity of the mixture, and the resulting nanofluid may provide better overall thermal management and better lubrication in many applications, such as heat transfer fluids, engine oils, transmission fluids, gear oils, coolants and other similar fluids and lubricants. The potential benefits of this technology to the automotive and related industries would be more efficient engines, reduced size and weight of the cooling and propulsion systems, lowered operating temperature of the mechanical systems, and increased life of the engine and other mechanical systems. The new mechanisms for this phenomenon of anomalous thermal conductivity increase have been proposed. The heat transfer properties of a series of graphite nanofluids were presented, and the experimental results were compared with the conventional heat transfer theory for pure liquids.

Hydroformed components are replacing stamped parts in automotive frames and front end and roof structures to improve the crash performance of vehicles. Due to the increasing application of hydroformed components, a better understanding of the crash behavior of these parts is necessary to improve the correlation between full-vehicle crash tests and FEM analysis. Accurately predicting the performance of hydroformed components will reduce the amount of physical crash testing necessary to develop the new components and new vehicles as well as reduce cycle time. Virgin material properties are commonly used in FEM analysis of hydroformed components, which leads to erroneous prediction of the full-vehicle crash response. Changes in gauge and material properties during the hydroforming process are intuitive and can be reasonably predicted by using forming simulations. The effects of the forming process have been investigated in the FEA models that are created for crash analyses.

System modeling and simulation results for an experimental switched reluctance external integral starter/generator (EISG) are reported. The EISG system employs a single switched reluctance machine and a generating system architecture that produces two separate 270 Vdc buses from that single switched reluctance machine. The machine has six phases with three of the phases connected to one converter supplying 125 kW to one 270 Vdc bus while the other three phases are connected to a second converter supplying 125 kW to the other 270 Vdc bus. Each bus has its own EMI filter and control in addition to its own converter. Two separate system models have been developed for the EISG. One of these models has been denoted the averaged model and the other has been denoted the detailed model. Both models include the switched reluctance machine and power electronics, the EMI filter, and the feedback control. The development of both of these models is described.

Partial enclosures are commonly utilized to reduce the radiated noise from equipment. Often, enclosure openings are fitted with silencers or louvers to further reduce the noise emitted. In the past, the boundary element method (BEM) has been applied to predict the insertion loss of the airborne path with good agreement with measurement. However, an alteration at the opening requires a new model and additional computational time. In this paper, a transfer function method is proposed to reduce the time required to assess the effect of modifications to an enclosure. The proposed method requires that the impedance at openings be known. Additionally, transfer functions relating the sound pressure at one opening to the volume velocity at other openings must be measured or determined using simulation. It is assumed that openings are much smaller than an acoustic wavelength. The sound power from each opening is determined from the specific acoustic impedance and sound pressure at the opening.

Partial enclosures are a very common way to reduce noise emissions from machinery. However, partial enclosures exhibit complex acoustic behavior that is difficult to predict. The boundary element method (BEM) was used to model the airborne path of a partial enclosure. Simulation results were compared to measurement with good agreement. Special attention is given to the determination of negative insertion loss. It is demonstrated that the enclosure insertion loss will be negative at the Helmholtz frequencies for the enclosure.

Micro-perforated panels have tiny pores which attenuate sound based on the Helmholtz resonance principle. That being the case, an appropriate cavity depth should be chosen to fully capitalize on the attenuation potential of the panel. Generally, the panel's sound absorbing performance can be predicted by Maa's theory given information about the panel and the cavity depth. However, in some cases, one cannot use the theory to predict the panel's performance precisely, especially when the micro-perforate has varying diameters and/or irregular hole shapes. In these cases, the sound-absorbing performance of the micro-perforate is different from that of a uniform pore diameter perforate. This paper presents an alternative method to predict the micro-perforated panel's performance precisely. As a first step, the transfer impedance of the micro-perforate should be measured.

This paper examines the feasibility of using the boundary element method (BEM) and the Rayleigh integral to assess the sound radiation from engine components such as oil pans. Two oil pans, one cast aluminum and the other stamped steel, are used in the study. All numerical results are compared to running engine data obtained for each of these oil pans on a Cummins engine. Measured running-engine surface velocity data are used as input to the BEM calculations. The BEM models of the oil pains are baffled in various ways to determine the feasibility of analyzing the sound radiated from the oil pan in isolation of the engine. Two baffling conditions are considered: an infinite baffle in which the edge of the oil pan are attached to an infinite, flat surface; and a closed baffle in which the edge of the oil pan is sealed with a rigid structure. It is shown that either of these methods gives satisfactory results when compared to experiment.

The two-load method is commonly used to determine the transmission loss of a muffler or silencer. Several practical measurement considerations are examined in this paper. First of all, conical adapters are sometimes used to transition between impedance tubes and the muffler. It is demonstrated that the effect of adding the adapter can be quite significant at low frequencies especially if the adapter is short in length. The effect of changing the length of the adapter was examined via measurement and plane wave theory. Secondly, the effect of selecting the reference microphone was examined experimentally. It was found that measurements are improved by selecting a downstream reference. Finally, the effect of using different frequency response function estimation algorithms (H1, H2 and Hv) was compared sans flow. This had little effect on the measurement.

A mathematical model is presented to help understand sheet metal deformation during forming. The particular purpose of this model is to predict the forming limit diagram (FLD). The present model is an extension of a previous analysis by Jones and Gillis (JG) in which the deformation is idealized into three phases: (I) homogeneous deformation up to maximum load; (II) deformation localization under constant load; (III) local necking with a precipitous drop in load. In phase III the neck geometry is described by a Bridgman type neck. The present model extends the JG theory which was applied to the right hand side of the FLD only. The main difference in treating the two different sides of the FLD lies in the assumptions regarding the width direction deformations. For biaxial stretching, the right hand side, the minor strain rate is assumed to be homogeneous throughout the process.

Properly characterizing input forces is an important part of simulating structure-borne noise problems. The purpose of this work was to apply a known force reconstruction technique to an earthmoving machinery cab to obtain input functions for modeling purposes. The technique was performed on a cab under controlled laboratory conditions to gain confidence in the method prior to use on actual machines. Forces were measured directly using force transducers and compared to results from the force reconstruction technique. The measured forces and vibrations were used as input power to an SEA model with favorable results.

Lack of a precise control over paint droplets released from current coating sprayers has motivated this study to develop an atomizer capable of generating a uniform flow of mono-dispersed droplets. In the current study, a numerical investigation based on CFD incorporating volume of fluid (VOF) multiphase model has been developed to capture the interface between air and paint phases for a typical atomizer equipped with piezoelectric actuator. Effects of inlet flow rate and actuator frequency on ejected droplets' characteristics, droplet diameter and their successive spacing are studied in detail. It will be shown that for a determined flow rate of paint, there is an optimum actuator frequency in which droplet size is minimum. Besides, there exists a direct relationship between the inlet paint velocity and obtained optimal actuator frequency.