Refine Your Search

Search Results

Viewing 1 to 12 of 12
Technical Paper

Near Nozzle Field Conditions in Diesel Fuel Injector Testing

2015-09-06
2015-24-2470
The measurement of the rate of fuel injection using a constant volume, fluid filled chamber and measuring the pressure change as a function of time due to the injected fluid (the so called “Zeuch” method) is an industry standard due to its simple theoretical underpinnings. Such a measurement device is useful to determine key timing and quantity parameters for injection system improvements to meet the evolving requirements of emissions, power and economy. This study aims to further the understanding of the nature of cavitation which could occur in the near nozzle region under these specific conditions of liquid into liquid injection using high pressure diesel injectors for heavy duty engines. The motivation for this work is to better understand the temporal signature of the pressure signals that arise in a typical injection cycle.
Technical Paper

More Torque, Less Emissions and Less Noise

2000-03-06
2000-01-0942
For many years, compression ignition combustion has been studied by a combination of generic studies on fuel spray formation and analysis of results from single and multicylinder engines. The results and insight have been applied to design and develop advanced fuel injection equipment for high-speed direct injection engines. Experimental fuel injection equipments, including early common rail designs, have been matched to combustion chambers in single cylinder research engines to tackle the conflicting requirements of efficiency and minimum nitric oxide formation, combustion noise and soot. A clear strategy evolved from the work with experimental equipment that is being applied to multicylinder engines. If sufficient oxygen is available in the gas charge trapped in each cylinder, the LDCR common rail injection system will provide the fuel required to develop high torque at low engine speeds.
Journal Article

Internal Fuel Injector Deposits

2011-08-30
2011-01-1925
The need for improved emissions and fuel economy are placing increasingly severe performance requirements on compression ignition engines. These are satisfied in part by advanced fuel injection equipment that provide multiple injections and increased injection pressures along with higher operating temperature. Fuel composition is also changing, with increased use of non-traditional feedstocks combined with a range of additive chemistries to restore or enhance fuel quality. Within this environment, a number of worldwide automotive companies have noted a trend towards increased Internal Injector Deposits (IID). Little quantitative information to understand the root cause is available, largely due to difficulty in reproducing the issue under controlled conditions. The present study details the results of an accelerated test methodology, which is used to evaluate the interrelated effects of fuel composition and operating environment.
Journal Article

Fuel Quality and Diesel Injector Deposits

2012-09-10
2012-01-1693
Internal deposits formed within the fuel injection system have been widely reported in the literature. Several root causes exist, with many deposits consisting of more than one material. The final chemistry depends on the availability of trace fuel contaminants and additives and to a lesser extent hydrocarbon/FAME stability and operating conditions. The present paper identifies the primary deposit morphologies, along with the typical root cause. Metal carboxylate salts, also known as metal soaps are most widely reported and are easily recreated under controlled conditions using compounds present at trace concentrations in some market fuels. The salting reaction may occur at low temperatures in the fuel supply system. It is proposed that the resulting fuel insoluble salt molecules are transported as reverse micelles, occasionally plugging filters but more commonly passing to the high pressure injection system.
Technical Paper

Evaluation of the Predictive Capability of Diesel Nozzle Cavitation Models

2007-04-16
2007-01-0245
The predictive capability of Lagrangian and Eulerian multi-dimensional computational fluid dynamics models accounting for the onset and development of cavitation inside Diesel nozzle holes is assessed against experimental data. These include cavitation images available from a real-size six-hole mini-sac nozzle incorporating a transparent window as well as high-speed/CCD images and LDV measurements of the liquid velocity inside an identical large-scale fully transparent nozzle replica. Results are available for different cavitation numbers, which correspond to different cavitation regimes forming inside the injection hole. Discharge coefficient measurements for various real-size nozzles operating under realistic injection pressures are also compared and match well with models' predictions.
Technical Paper

Evaluation of the Operating Range of Partially Premixed Combustion in a Multi Cylinder Heavy Duty Engine with Extensive EGR

2009-04-20
2009-01-1127
Partially Premixed Combustion (PPC) is a combustion concept by which it is possible to get low smoke and NOx emissions simultaneously. PPC requires high EGR levels and injection timings sufficiently early or late to extend the ignition delay so that air and fuel mix extensively prior to combustion. This paper investigates the operating region of single injection diesel PPC in a multi cylinder heavy duty engine resembling a standard build production engine. Limits in emissions and fuel consumption are defined and the highest load that fulfills these requirements is determined. Experiments are carried out at different engine speeds and a comparison of open and closed loop combustion control are made as well as evaluation of an extended EGR-cooling system designed to reduce the EGR temperature. In this study the PPC operating range proved to be limited.
Technical Paper

Evaluation of Fischer-Tropsch Fuel Performance in Advanced Diesel Common Rail FIE

2010-10-25
2010-01-2191
An increasing range of conventional and unconventional feed stocks will be used to produce fuel of varying chemical and physical properties for use in compression ignition engines. Fischer-Tropsh (F-T) technology can be used to produce fuels of consistent quality from a wide range of feed stocks. The present study evaluates the performance of F-T fuel in advanced common rail fuel injection systems. Laboratory scale tests are combined with proprietary engine and electrically driven common rail pump hydraulic rig tests to predict long-term performance. The results obtained indicate that the performance of F-T fuel is at least comparable to conventional hydrocarbon fuels and superior in a number of areas. In particular, the lubricity of F-T fuel was improved by addition of lubricity additives or FAME, with minimal wear under a wide range of operating conditions and temperatures.
Technical Paper

Effect of Diesel and Water Co-injection with Real-Time Control on Diesel Engine Performance and Emissions

2008-04-14
2008-01-1190
A system for injection of diesel fuel and water with real-time control, or real-time water injection (RTWI), was developed and applied to a heavy-duty diesel engine. The RTWI system featured electronic unit pumps that delivered metered volumes of water to electronic unit injectors (EUI) modified to incorporate the water addition passages. The water and diesel mixed in the injector tip such that the initial portion of the injection contained mostly diesel fuel, while the balance of the injection was a water and diesel mixture. With this hardware, real-time cycle-by-cycle control of water mass was used to mitigate soot formation during diesel combustion. Using RTWI alone, NOx emissions were reduced by 42%. Using high-pressure-loop exhaust gas recirculation (EGR) and conventional diesel combustion with RTWI, the NOx was reduced by 82%.
Technical Paper

Development of Premixed Low-Temperature Diesel Combustion in a HSDI Diesel Engine

2008-04-14
2008-01-0639
The pursuit of new combustion concepts or modes is ongoing to meet future emissions regulations and to eliminate or at least to minimize the burden of aftertreatment systems. In this research, Premixed Low Temperature Diesel Combustion (PLTDC) was developed using a single-cylinder engine to achieve low NOx and soot emissions while maintaining fuel efficiency. Operating conditions considered were 1500 rpm, 3 bar and 6 bar IMEP. The effects of injection timing, injection pressure, swirl ratio, EGR rate, and multiple injection strategies on the combustion process have been investigated. The results show that low NOx and soot emissions can be obtained at both operating conditions without sacrificing the fuel efficiency. Low NOx and soot emissions are achieved through minimization of peak temperatures during the combustion process and homogenization of in-cylinder air-fuel mixture.
Technical Paper

Deposit Formation in the Holes of Diesel Injector Nozzles: A Critical Review

2008-10-06
2008-01-2383
Current developments in fuels and emissions regulations are resulting in increasingly severe operating environment for the injection system. Formation of deposits within the holes of the injector nozzle or on the outside of the injector tip may have an adverse effect on overall system performance. This paper provides a critical review of the current understanding of the main factors affecting deposit formation. Two main types of engine test cycles, which attempt to simulate field conditions, are described in the literature. The first type involves cycling between high and low load. The second involves steady state operation at constant speed either at medium or high load. A number of influences on the creation of deposits are identified. This includes fouling through thermal condensation and cracking reactions at nozzle temperatures of around 300°C. Also the design of the injector holes is an influence, because it can influence cavitation.
Technical Paper

Cepstrum Analysis of a Rate Tube Injection Measurement Device

2016-10-17
2016-01-2196
With a push to continuously develop traditional engine technology efficiencies and meet stringent emissions requirements, there is a need to improve the precision of injection rate measurement used to characterise the performance of the fuel injectors. New challenges in precisely characterising injection rate present themselves to the Original Equipment Manufacturers (OEMs), with the additional requirements to measure multiple injection strategies, increased injection pressure and rate features. One commonly used method of measurement is the rate tube injection analyser; it measures the pressure wave caused by the injection within a column of stationary fluid. In a rate tube, one of the significant sources of signal distortion is a result of the injected fluid pressure waves reflected back from the tube termination.
Technical Paper

Advanced Two-Actuator EUI and Emission Reduction for Heavy-Duty Diesel Engines

2003-03-03
2003-01-0698
A very flexible choice of fuel injection characteristics can be obtained with an advanced electronic unit injector that has been developed with two electronically controlled valves. Single-cylinder engine tests have demonstrated the potential of this advanced EUI system for a heavy-duty diesel engine. Substantial increases in injection pressure can be programmed electronically at individual engine speed/load conditions, compared with a baseline EUI system, to provide much faster rates of air/fuel mixing. Simulated US and European emissions cycle results, with the optimised two-actuator EUI and EGR, show substantially improved soot particulate versus NOx results and lower BSFC compared with a baseline EUI result. A high-pressure post injection has the potential to give further soot reduction.
X