Search Results

A test cell was developed for evaluating a 6-speed automatic transmission. The target vehicle had an internal combustion 5.4L gasoline V8 engine. An electric dynamometer was used to closely simulate the engine characteristics. This included generating mean torque from the ECU engine map, with a transient capability of 10,000 rpm/second. Engine inertia was simulated with a transient capability of 20,000 rpm/second, and torque pulsation was simulated individually for each piston, with a transient capability of 50,000 rpm/second. Quantitative results are presented for the correlation between the engine driven and the dynamometer driven transmission performance over more than 60 test cycles. Concerns about using the virtual engine in validation testing are discussed, and related to the high frequency transient performance required from the electric dynamometer. Qualitative differences between the fueled engine and electric driven testing are presented.

In order to meet progressively stringent regulations on particulate emission from diesel engines, GM has developed and tested a variety of trap oxidizer systems over the years. A particulate trap system for a light duty diesel engine has been selected and developed based on this experience, with particular emphasis on production feasibility. The system components have been designed and developed in collaboration with potential suppliers, to the extent possible. The technical performance of this system has been demonstrated by successful system durability testing in the test cell and vehicle experience in computer controlled automatic operation mode. Although the system shows promise, its production readiness will require more development and extensive vehicle validation under all operating conditions.

A running loss test procedure has been developed which integrates a point-source collection method to measure fuel evaporative running loss from vehicles during their operation on the chassis dynamometer. The point-source method is part of a complete running loss test procedure which employs the combination of site-specific collection devices on the vehicle, and a sampling pump with sampling lines. Fugitive fuel vapor is drawn into these collectors which have been matched to characteristics of the vehicle and the test cell. The composite vapor sample is routed to a collection bag through an adaptation of the ordinary constant volume dilution system typically used for vehicle exhaust gas sampling. Analysis of the contents of such bags provides an accurate measure of the mass and species of running loss collected during each of three LA-4* driving cycles. Other running loss sampling methods were considered by the Auto-Oil Air Quality Improvement Research Program (AQIRP or Program).

The design and construction of the rail transit simulator for the dynamic testing of automobiles, trucks and components is described. The test facility features seven servo-controlled hydraulic actuators, along with associated electronics to simulate vehicle environmental conditions during rail shipment. This ability to simulate the shipping environment in the laboratory has effectively reduced the cost and the time required to evaluate designs.

As part of an effort to develop a laboratory steering system durability test, power steering system test procedure development was conducted. Fatigue damage to steering systems caused by road roughness was quantified utilizing data recorded from instrumented test vehicles and customer survey results. In addition, data recorded from customer vehicles were employed to determine fatigue damage to steering systems caused by driving style and road style inputs. Proving ground steering system test procedures that generate the same amount of damage to a steering system as that accumulated by the design target percentile customer for the design target miles of public road usage were developed.

Reduction of lead time between design and production is possible through application of modern test techniques. Such techniques involve accurate measurement of customer service load cycle and application of these measured loads to the laboratory and proving ground. Correlation of customer usage with “in house” testing is essential to a realistic projection of test results into anticipated service life.

The Auto/Steel Partnership established the Light Truck Frame Project Group in 1996 with two objectives: (a) to develop materials, design and fabrication knowledge that would enable the frames on North American OEM (original equipment manufacturer) light trucks to be reduced in weight, and (b) to improve corrosion resistance of frames on these vehicles, thereby allowing a reduction in the thickness of the components and a reduction in frame weight. To address the issues relating to corrosion, a subgroup of the Light Truck Frame Project Group was formed. The group comprised representatives from the North American automotive companies, test laboratories, frame manufacturers, and steel producers. As part of a comprehensive test program, the Corrosion Subgroup has completed tests on frame coatings. Using coated panels of a low carbon hot rolled and pickled steel sheet and two types of accelerated cyclic corrosion tests, seven frame coatings were tested for corrosion performance.

Proving Ground cyclic testing was used to evaluate vehicles assembled with electrogalvanized and organic composite coated electrogalvanized steel. These same materials, along with several commonly available precoated steels, were also evaluated as hem flange assemblies on towed trailers at the Proving Ground. Testing was terminated as perforation of some of the assemblies occurred. Pitting depth was used to quantitatively evaluate metal loss.

Through Frame and Suspension Tuning (FAST) you can identify suspension and frame Set-ups in the lab with out risk to the car or driver. For on track verification the number of Set-ups can be reduced from an unlimited number to 2 or 3 and then optimized on the track, rather than developed on the track. This method can be used with all forms of racing. It has been applied to Indy, GT, Winston Cup, and Trans Am cars. Through the use of a road simulator we are able to evaluate and improve the frame and suspension dynamics in a laboratory. This paper will focus on the first step in the tuning process, frame tuning. If the frame is not tuned for the input energy conditions it can become an uncontrolled suspension component. The first step is to identify the frame dynamic characteristics. Operational deform shapes are measured to identify local and global motion. The frames are modified to optimize the response for the type of race track.

HUMAN perception thresholds to motions and the various characteristics of motions in six degrees of freedom are presented. Experiments made to establish these thresholds for disturbances of the duration or frequency that might arise from highway geometry—durations in the range of from one second to several hundred seconds—are described. Applications of motion sensitivity criteria in the design of vertical and horizontal highway curves and transitions are developed, with examples from company proving grounds in Arizona and Michigan. The resulting geometric features of the high-speed road systems differ in several important respects from conventional highway practice and previous automotive test-track designs.

During the development of a new friction material, besides the interface between lining/drum is also fundamental take in account all aspects involving the attachment of the linings on the brake shoes. This paper presents an optimization approach to the development and manufacturing parameters of brake linings, applied on medium and heavy duty commercial vehicles, aiming to assure the correct specification of the riveted joint clamp forces. These evaluations were conducted based on the quality tools documents and the theoretical aspects of the product usage as well as the modeling of key elements of the referred mechanism throughout various known applications. A calculation methodology was developed based on brake geometry, its generated forces and braking reactions required for each vehicle family.

The Multi Material Lightweight Vehicle (MMLV) developed by Magna International and Ford Motor Company is a result of a US Department of Energy project DE-EE0005574. The project demonstrates the lightweighting potential of a five passenger sedan, while maintaining vehicle performance and occupant safety. Prototype vehicles were manufactured and limited full vehicle testing was conducted. The MMLV vehicle design, comprised of commercially available materials and production processes, achieved a 364kg (23.5%) full vehicle mass reduction, enabling the application of a 1.0-liter three-cylinder engine resulting in a significant environmental benefit and fuel reduction. The three key requirements of structural performance evaluation for vehicle development are NVH, durability and safety.

Computer simulation technology coupled with indoor laboratory facilities is being used in the automotive industry to provide up-front assessment of vehicle performance. This paper presents a technique to evaluate passenger vehicle tire wear performance as related to suspension and tire design early in the design process. Motivation for developing this tool is to optimize suspension and tire design to tire wear early in the design process. This approach has resulted in reductions in vehicle development time, dependency on outdoor testing and the need for expensive prototype vehicles. A full vehicle ADAMS model of a production vehicle is used to animate vehicle suspension kinematic motions, and dynamic tire forces of vehicle maneuvers for a preselected outdoor tire wear route. Time histories of five vehicle parameters are generated: radial force, slip angle or lateral force, camber, velocity and driving and braking torques.

The Vehicle Exhaust Emissions Simulator was developed to evaluate the performance of vehicle emissions sampling and analytical systems. The simulator produces a representative tailpipe volume flow rate containing up to five emission constituents, injected via mass flow controllers (MFCs). Eliminating the variability of test results associated with the vehicle, driver, and dynamometer makes the simulator an ideal quality control tool for use in commissioning new test cells, checking data correlation between test cells, and evaluating overall system performance. Earlier vehicle emissions simulators being used in the industry were primarily for checking Constant Volume Samplers (CVSs) and Bag Benches but they did not have the ability to properly simulate tailpipe volume.

THE METHOD of validating proving ground test routines as a sample of customer operations is described. Comparisons of field survey and proving ground failure statistics are analyzed to establish sample reliability and severity ratios. Alternative means of accelerating the test program are considered, with examples indicating the effect on correlation. Use of proving ground routes as a link in establishing laboratory test to customer service correlation is treated. Procedures and instrumentation for developing load cycle information on the road, and programming random load cycles into laboratory test fixtures for simulated service life testing are discussed with some examples of applications to automotive components. In the performance test area, several performance parameters representative of customer requirements are developed. Techniques of improving comparative evaluations by eliminating the effect of extraneous variables such as the driver and the weather are presented.

Friction and scuffing resistance characteristics of two piston alloy materials have been investigated by using a long-stroke reciprocating test rig. Tests were conducted under the same load, speed, and starved changing to dry lubrication conditions until the scuffing failure occurred, as indicated by a sudden change of the frictional force signal which was monitored continuously. Measured friction coefficient and scuffing threshold and life results were obtained, and the piston alloy with the better scuffing resistance capability has been identified. Surface texture of new and scuffed piston and cylinder bore specimen surfaces have been measured and characterized by a combination of amplitude and spacing parameters.

Improvement of engine fuel efficiency through the use of low friction engine oils is a major task in engine lubrication research. This friction reduction can be achieved by improving the rheological characteristics and elastohydrodynamic (EHD) properties of engine oils, and by controlling boundary chemical interactions between oil-based additives and lubricated components in the engine. In order to achieve minimal frictional power loss under all lubrication regimes, engine tribological systems must be designed to effectively use advanced lubricant technology, material and surface modifications. This paper presents results of cooperative research addressing opportunities for minimizing friction through extension of hydrodynamic lubrication regime in lubricated components using various formulation approaches. A set of experimental oils has been evaluated using laboratory test rigs that simulate hydrodynamic, EHD, mixed and boundary lubrication.

For future hydrogen fueled ground vehicle research, Ford Motor Company has installed the first hydrogen fueling station in North America with gaseous and cryogenic hydrogen and two dedicated hydrogen fueled engine laboratory dynamometer test cells. Hydrogen, as a fuel for internal combustion engines (ICE), requires unique approaches to assure safety and accuracy in an engine-testing lab because of hydrogen's molecular size, compressibility, and reactivity. Ford Scientific Research Lab has accumulated useful experiences during the P2000 hydrogen internal combustion engine and vehicle development program. This paper presents the safety measures used in the hydrogen lab, including gas leakage sensing and warning system, hydrogen flame detecting device, cell fresh air ventilation conventions, and hydrogen fueling and purging system.

Clutch wear is dominantly manifested as the reduction of friction plate thickness. For dry dual clutch with position-controlled electromechanical actuators this affects the accuracy of normal force control because of the increased clutch clearance. In order to compensate for the wear, dry dual clutch is equipped with wear compensation mechanism. The paper presents results of experimental characterization and mathematical modeling of two clutch wear related effects. The first one is the decrease of clutch friction plate thickness (i.e. increase of clutch clearance) which is described using friction material wear rate experimentally characterized using a pin-on-disc type tribometer test rig. The second wear related effect, namely the influence of the clutch wear compensation mechanism activation at various stages of clutch wear on main clutch characteristics, was experimentally characterized using a clutch test rig which incorporates entire clutch with related bell housing.

Thermal expansion of a clutch pack with position-controlled actuation can affect the accuracy of clutch normal torque control, because it causes an increase of the clutch normal force for the given actuator position. The paper presents an experimental characterization and mathematical modeling of the dry dual clutch thermal expansion effects. The experimental data have been collected by using a clutch/transmission test rig. The acquired data point to two separate, mutually opposite thermal expansion effects. The first effect relates to increase of the clutch clearance with temperature growth, while the second one includes decrease of press plate and engagement bearing positions for a given clutch torque and a rising temperature (i.e. the clutch torque rises with temperature growth and a constant actuator position). In order to explain and describe these two effects, a geometry analysis of the clutch, focused on thermal expansion, is carried out.