Search Results

A special vehicle dynamometer has been developed that allows engineers to evaluate driveline components and control algorithms for advanced, electrically-assisted drive systems on commercial vehicles. This dynamometer allows objective measurements of performance, fuel economy, and exhaust emissions, while the full vehicle is operated over a specified driving cycle. This system can be used to exercise the electric motor, engine, transmission and battery systems on Medium Duty Hybrid Trucks - in regeneration as well as power mode - all indoors and in a controlled, repeatable environment. This paper will provide descriptions of the operating goals, control features, and results of testing with this dynamometer. Once the various parameters have been optimized for fuel and emissions performance in this facility, the vehicle can be evaluated where it counts - on the road.

An LNT + SCR diesel aftertreatment system was developed in order to meet the 2010 US HD EPA on-road, and tier 4 US HD EPA off-road emission standards. This system consists of a fuel reformer (REF), lean NOx trap (LNT), catalyzed diesel particulate filter (DPF), and selective catalytic reduction (SCR) catalyst arranged in series to reduce tailpipe nitrogen oxides (NOx) and particulate matter (PM). This system utilizes a REF to produce hydrogen (H2), carbon monoxide (CO) and heat to regenerate the LNT, desulfate the LNT, and actively regenerate the DPF. The NOx stored on the LNT is reduced by the H2 and CO generated in the REF converting it to nitrogen (N2) and ammonia (NH3). NH3, which is normally an undesired byproduct of LNT regeneration, is stored in the downstream SCR which is utilized to further reduce NOx that passes through the LNT. Engine exhaust PM is filtered and trapped by the DPF reducing the tailpipe PM emissions.

Diesel Cylinder Deactivation (CDA) has been shown in previous work to increase exhaust temperatures, improve fuel efficiency, and reduce engine-out NOx for engine loads up to 3 bar BMEP. The purpose of this study is to determine whether or not the turbocharger needs to be altered when implementing CDA on a diesel engine. This study investigates the effect of CDA on exhaust temperature, fuel efficiency, and turbocharger performance in a 15L heavy-duty diesel engine under low-load (0-3 bar BMEP) steady-state operating conditions. Two calibration strategies were evaluated. First, a “stay-hot” thermal management strategy in which CDA was used to increase exhaust temperature and reduce fuel consumption. Next, a “get-hot” strategy where CDA and elevated idle speed was used to increase exhaust temperature and exhaust enthalpy for rapid aftertreatment warm-up.

The automotive industry has seen accelerating demand for electrified transportation. While the complexity of conventional ICE vehicles has increased, the powertrain still largely consists of a mechanical system. In contrast, vehicle architectures in electrified transportation are a complex integration of power electronics, batteries, control units, and software. This shift in system architecture impacts the entire organization during new product development, with increased focus on high power electronic components, energy management strategies, and complex algorithm development. Additionally, product development impact extends beyond the vehicle and impacts charging networks, electrical infrastructure, and communication protocols. The complex interaction between systems has a significant impact on vehicle safety, development timeline, scope, and cost.

With the increasing demand for efficient & clean transport solutions, applications such as road transport vehicles, aerospace and marine are seeing a rise in electrification at a significant rate. Irrespective of industries, the main source of power that enables electrification in mobility applications like electric vehicles (EV), electric ships and electrical vertical take-off & landing (e-VTOL) is primarily a battery making it fundamentally a DC system. Fast charging solutions for EVs & e-VTOLs are also found to be DC in nature because of several advantages like ease of integration, higher efficiency, etc. Likewise, the key drivers of the electric grid are resulting in an energy transition towards renewable sources, that are also essentially DC in nature. Overall, these different business trends with their drivers appear to be converging towards DC power systems, making it pertinent.

With the advent of wide band gap semiconductor devices like SiC based MOSFETs/Diodes, there is a growing demand for utilizing electrical power instead of the conventional fuel-based power generation in both automotive and aerospace industry. In automotive/aerospace industry the focus on electrification has resulted in a need for sub-systems like inverters, power distribution units, motor controllers, DC-DC converters that actively utilize SiC based power electronics devices. To address the growing power density requirements for electronics in next generation product families, more efficient & reliable thermal management solution plays a critical role. The effective thermal management of the power electronics is also critical aspect to ensure overall system reliability. The conventional thermal management system (TMS) optimization targets heat sink/ cold plate design parameters like fin spacing, thickness, height etc. or sizing of the required cooling pump/fan.

A detailed study, by finite element method (FEM), was conducted on an automotive engine exhaust valve subject to various loads (i.e. spring load, combustion pressure load, temperature profile and valve impact closing velocity). The 3D nonlinear (contact element and temperature-dependent) thermal-mechanical model was constructed and implicit time integration method was employed in transient dynamics under impact velocity. The predicted temperatures and maximum valve stress under impact velocity via FEM were compared with the measured test data, which were in good agreement. In addition, this study finds that the energy transfer during valve closing in normal engine operation is mainly conservative, and a linear relation exists between valve closing velocity and maximum stem stress, that was also confirmed by both test data and analytical expression presented using elastic wave and vibration theory.

Typical traction control systems based on brake intervention have the disadvantage of dissipating an amount of energy roughly equal to that spent in biasing the high-friction wheel. Fully locked differentials achieve the best possible longitudinal traction but, in situations such as slippery or split-friction (split-μ) surfaces, the lateral dynamics of the vehicle can be degraded and deviate from the driver's intended direction. This paper presents an active stability control strategy using electronic limited slip differentials to enhance the vehicle lateral dynamics while preserving longitudinal motion. The proposed control system includes stability enhancement of the traction control and yaw stability control. The stability-enhanced traction control is evaluated under the condition of straight-line full-throttle launching on a split-μ ice/snow surface. The experimental data show a significant stability improvement in a traction mode.

The use of electrical contacts in aerospace applications is crucial, particularly in connectors that transmit signal and power. Crimping is a widely preferred method for joining electrical contacts, as it provides a durable connection and can be easily formed. This process involves applying mechanical load to the contact, inducing permanent deformation in the barrel and wire to create a reliable joint with sufficient wire retention force. This study utilizes commercially available Abaqus software to simulate the crimping process using an explicit solver. The methodology developed for this study correlates FEA and testing for critical quality parameters such as structural integrity, mechanical strength, and joint filling percentage. A four-indenter crimping tool CAD model is utilized to form the permanent joint at the barrel-wire contact interfaces, with displacement boundary conditions applied to the jaws of the tool in accordance with MIL-C-22520/1C standard.

An aftertreatment system for medium and heavy-duty diesel engines has been modeled for U.S. 2010 application. The aftertreatment system is comprised of a lean NOx trap (LNT) and an ammonia selective catalytic reduction (SCR) catalyst in series. Descriptions of the fully transient, one-dimensional LNT and SCR models are presented. The models simulate flow, heat transfer, and chemical reactions in the LNT and SCR catalysts. The models can be used to predict catalyst performance over a range of operating conditions and driving cycles. Simulated results of NOx conversion efficiency, species concentrations, and gas temperature were compared to experimental data for a 13-mode test. The model results showed the LNT-SCR model predicts system performance with reasonable accuracy in comparison to experimental data. Therefore, two model applications were investigated. First, LNT and SCR volumes were varied to examine the effect on NOx conversion efficiency and NH3 production.

Recent studies have shown that hydraulic hybrid drivelines can significantly improve fuel savings for medium weight vehicles on stop-start drive cycles. In a series hydraulic hybrid (SHH) architecture, the conventional mechanical driveline is replaced with a hydraulic driveline that decouples vehicle speed from engine speed. In an effort to increase the design space, this paper explores the use of a fixed displacement checkball piston pump in an SHH driveline. This paper identifies the potential life-limiting components of a fixed displacement checkball piston pump and examines the likelihood of surface fatigue in the check valves themselves. Numerical analysis in ABAQUS software suggests that under worst case operating conditions, cyclic pressure loading will result in low-cycle plastic deformation of check valve surfaces.

An advanced exhaust aftertreatment system is characterized following end-of-life catalyst aging to meet final Tier 4 off-highway emission requirements. This system consists of a fuel dosing system, mixing elements, fuel reformer, lean NOx trap (LNT), diesel particulate filter (DPF), and a selective catalytic reduction (SCR) catalyst. The fuel reformer is used to generate hydrogen (H2) and carbon monoxide (CO) from injected diesel fuel. These reductants are used to regenerate and desulfate the LNT catalyst. NOx emissions are reduced using the combination of the LNT and SCR catalysts. During LNT regeneration, ammonia (NH3) is intentionally released from the LNT and stored on the downstream SCR catalyst to further reduce NOx that passed through the LNT catalyst. This paper addresses system durability as the catalysts were aged to 500 desulfation events using an off-highway diesel engine.

On-board measurements of fuel consumption and vehicle exhaust emissions of NOx, HC, CO, CO2, and PM are being conducted for three types of commercially available city buses in Guangzhou, China. The selected vehicles for this test include a diesel bus with Eaton hybrid electric powertrain, a conventional diesel bus with automated mechanical transmission (AMT), and a LPG powered city bus with manual transmission (MT). All of the tested vehicles were instrumented with on-board measurements. Horiba OBS-2200 was used for measuring NOx, HC, and CO emissions; ELPI (Electrical Low Pressure Impactor) was used for PM measurement. The vehicles were tested at Hainan National Proving Ground in southern China. Test data of fuel consumption and exhaust emissions were analyzed. The city bus with Eaton hybrid electric powertrain demonstrated more than 27% fuel consumption reduction over the conventional diesel powered bus, and over 68% over the LPG bus.

This paper presents the modeling of an Electromagnetic Valve Actuator (EMV). A nonlinear model is formulated and presented that takes into account secondary nonlinearities like hysteresis, saturation, bounce and mutual inductance. The uniqueness of the model is contained in the method used in modeling hysteresis, saturation and mutual inductance. Theoretical and experimental methods for identifying parameters of the model are presented. The nonlinear model is experimentally validated. Simulation and experimental results are presented for an EMV designed and built in our laboratory. The experimental results show that sensorless estimation could be a possible solution for position control.

The paper covers the NOx performance evaluation of an LNT + SCR system designed to meet the 2010 on-highway heavy-duty (HD) US EPA emission standards. The system combines a fuel reformer catalyst (REF), lean NOx trap (LNT), diesel particulate filter (DPF), and selective catalytic reduction (SCR) in series, to reduce engine-out NOx and PM. System NOx reduction performance was verified in an engine dynamometer test cell, using a 2007 7.6L medium-duty engine. System NOx performance was characterized using fresh LNT and SCR along with hydrothermal aged LNT and fresh SCR. Test results show levels consistent with EPA 2010 limits under various test conditions. Catalysts performance was characterized at eight steady engine-operating conditions (A100, B50, B75, A75, B100, C100, C75, C50, across a 13-mode Supplemental Emission Test (SET), and an on-highway Heavy Duty Federal Test Procedure (HD-FTP).

This paper presents an empirical dynamic model of a single spring electromagnetic solenoid actuator system, including bounce, temperature effects and coil leakage inductance. The model neglects hysteresis and saturation, the aim being to compensate for these uncertainties through estimator robustness. The model is validated for all regions of operation and there is a good agreement between model and experimental data. A nonlinear (sliding mode) estimator is developed to estimate position and speed from current measurements. Since the estimator makes use of only current measurement it is given the name sensorless. The estimator is validated in simulation and experimentally. The novelty in this paper lies in the fact that accurate state estimation can be realized on a simple linear model using a robust observer theory. Also, the formulations for leakage inductance and coil temperature are unique.

Car hauler ramps have historically been hydraulically positioned via banks of manual control valves that provide limited operator visibility and flexibility. On some enclosed type haulers, manual valves are not feasible. An electro-hydraulic system has been developed utilizing on/off solenoid valve stacks. A handheld control unit with a membrane switch pad communicates with a valve interface module near each valve stack. The handheld unit and the interface modules each have microprocessor circuitry to provide intelligent distributed control. Self monitoring circuitry provides safety features and system diagnostics. Wiring harness assemblies connect the valve stacks to the interface modules. A retractile cable from the handheld unit to the trailer allows improved operator mobility and visibility. An infrared wireless interface between the trailer and handheld unit will also be available.

In an effort to improve the reliability of electronic control modules used to automate operation of trucks, a database was conceived to aid in the proper selection of electronic components. An accompanying application program provided a means of information exchange between the user and the database, while controlling (accessing, updating, and navigating through) the database.

Compared to the internal-combustion-engine (ICE) vehicles on the road today, Electric Vehicles (EV) deliver more torque to vehicle wheels, and require smaller driveline packaging envelopes. Current differentials use asymmetrical ring gears with differential housings that are roughly a third of the tire outside diameter. New differential architecture concepts are shown here to deliver more torque to the wheels, while decreasing the height of the differential as much as fourfold. Most EV’s are driven by one or more torsion motors, delivering torque to the left side and the right side of the EV’s at different speeds during a vehicle turn, or a wheel “spinout.” At low speeds, the EV motors deliver more torque to the wheels than comparably sized ICE vehicles, so EV differentials must be built stronger and stiffer to manage the distribution of available drive torque.

A number of different data networks have been implemented for electronic control unit communication in vehicles to date. Each network serves a particular need, such as low-cost networking of cab components or high-speed networking of powertrain components. Although each communication network performs its original purpose, the different communication networks, especially those using hardware-based messaging protocols, are expensive to integrate for information sharing and are not readily upgradeable with new messages. This is complicated by the growing number of different communication networks for vehicles, often driven by OEM and supplier technology consortiums rather than by end-user requirements. The result is added vehicle-support costs for the OEM, dealership and customer to maintain multiple networks.