Search Results

Lubricant formulation was found to have dramatic impact on legislated emissions in a study using an ultra low sulphur fuel, a 12 litre naturally aspirated Euro I representative engine and tested over the ECE R49 test cycle. An SAE 10W-40 high quality part-synthetic heavy duty diesel engine oil was found to generate over 20% less particulate matter than two fully synthetic products of higher performance specification (SAE 5W-40 and 10W-40), whereas the fully synthetic oils showed a 10% reduction in Nox. All three oils are commercially available. The part-synthetic and fully synthetic oils also reduced fuel consumption relative to the SAE 15W-40, all mineral oil reference oil (0.4 - 0.9%). Higher oil consumption related to lower lubricant viscosity index improver content in the synthetic products can explain the results although more work is needed. Alternatively, there is some evidence that the dynamic fuel injection timing may be effected by the lubricants viscometric properties.

Fuel volatility and vehicle characteristics have long been recognised as important parameters influencing the exhaust emissions and the driveability of gasoline vehicles. Limits on volatility are specified in a number of world-wide / national fuel specifications and, in addition, many Oil Companies monitor driveability performance to ensure customer satisfaction. However, the relationship between driveability and exhaust emissions is relatively little explored. A study was carried out to simultaneously measure driveability and exhaust emissions in a fleet of 10 European gasoline vehicles. The vehicles were all equipped with three-way catalysts and single or multi-point fuel injection. The test procedure and driving cycle used were based on the European Cold Weather Driveability test method.

The future of diesel-engine-powered passenger cars and light-duty vehicles in the United States depends on their ability to meet Federal Tier 2 and California LEV2 tailpipe emission standards. The experimental purpose of this work was to examine the potential role of fuels; specifically, to determine the sensitivity of engine-out NOx and particulate matter (PM) to gross changes in fuel formulation. The fuels studied were a market-average California baseline fuel and three advanced low sulfur fuels (<2 ppm). The advanced fuels were a low-sulfur-highly-hydrocracked diesel (LSHC), a neat (100%) Fischer-Tropsch (FT100) and 15% DMM (dimethoxy methane) blended into LSHC (DMM15). The fuels were tested on modern, turbocharged, common-rail, direct-injection diesel engines at DaimlerChrysler, Ford and General Motors. The engines were tested at five speed/load conditions with injection timing set to minimize fuel consumption.

Many researchers have reported the measurement of high numbers of emitted particles from gasoline vehicles operating at high speed. To date, in the absence of standard test protocols or analytical techniques, these measurements have all been made from a dilution tunnel set up according to regulatory procedures. Currently, there is great uncertainty relating to the use of the dilution tunnel as a suitable tool for the measurement of automotive particle size and number distribution and also the relevance of the procedure to ambient measurement of the same parameters. Gasoline particle number emissions, as measured on a dilution tunnel, are low at speeds under 120km/h. Beyond this speed, high numbers of very small particles have been measured. There is some evidence to show that these particles may be formed as an artefact within the sampling system, either from the desorption of deposited material or from the pyrolysis of other material in the sampling system itself.

As boosted, direct injected gasoline engines become more prevalent in the automotive market, the boosting system architecture and efficiency are intimately entwined with the efficiency and performance of the engine. Single-stage as well as two-stage boosting systems, comprising of either two turbochargers or a supercharger in combination with a turbocharger, are potential configurations. When combining an internal combustion engine with boosting hardware, a mechanical, fluid-dynamic and thermodynamic coupling is created and the system as a whole will need to be treated as such.

In 1997 the US EPA formed a Heavy-Duty Engine Working Group (HDEWG) in the Mobile Sources Technical Advisory Subcommittee to address the questions related to fuel property effects on heavy-duty diesel engine emissions. The Working Group consisted of members from EPA and the oil refining and engine manufacturing industries. The goal of the Working Group was to help define the role of the fuel in meeting the future emissions standards in advanced technology engines (beyond 2004 regulated emissions levels). To meet this objective a three-phase program was developed. Phase I was designed to demonstrate that a prototype engine, located at Southwest Research Institute, represented similar emissions characteristics to that of certain manufacturers prototype engines. Phase II was designed to document the effects of selected fuel properties using a statistically designed fuel matrix in which cetane number, density, and aromatic content and type were the independent variables.

Previous studies have shown that regenerating particulate filters are very effective at reducing particulate matter emissions from diesel engines. Some particulate filters are passive devices that can be installed in place of the muffler on both new and older model diesel engines. These passive devices could potentially be used to retrofit large numbers of trucks and buses already in service, to substantially reduce particulate matter emissions. Catalyst-type particulate filters must be used with diesel fuels having low sulfur content to avoid poisoning the catalyst. A project has been launched to evaluate a truck fleet retrofitted with two types of passive particulate filter systems and operating on diesel fuel having ultra-low sulfur content. The objective of this project is to evaluate new particulate filter and fuel technology in service, using a fleet of twenty Class 8 grocery store trucks. This paper summarizes the truck fleet start-up experience.