Search Results

Nitrites have long been added to heavy-duty coolant to inhibit iron cylinder liner corrosion initiated by cavitation. However, in heavy-duty use, nitrites deplete from the coolant, which then must be refortified using supplemental coolant additives (SCA's). Recently, carboxylates have also been found to provide excellent cylinder liner protection in heavy-duty application. Unlike nitrites, carboxylate inhibitors deplete slowly and thus do not require continual refortification with SCA's. In the present paper laboratory aging experiments shed light on the mechanism of cylinder liner protection by these inhibitors. The performance of carboxylates, nitrites and mixtures of the two inhibitors are compared. Results correlate well with previously published fleet data. Specifically, rapid nitrite and slow carboxylate depletion are observed. More importantly, when nitrite and carboxylates are used in combination, nitrite depletion is repressed while carboxylates deplete at a very slow rate.

In this paper, residual stress distributions in rectangular bars due to rolling or burnishing at very high rolling or burnishing loads are investigated by roll burnishing experiments and three-dimensional finite element analyses using ABAQUS. First, roll burnishing experiments on rectangular bars at two roller burnishing loads are presented. The results indicate the higher burnishing load induces lower residual stresses and the higher burnishing load does not improve fatigue lives. Next, in the corresponding finite element analyses, the roller is modeled as rigid and the roller rolls on the flat surface of the bar with a low coefficient of friction. The bar material is modeled as an elastic-plastic strain hardening material with a nonlinear kinematic hardening rule for loading and unloading.

A typical cab used on agriculture machines is made up of a metal frame structure with large enclosing panels of glass, plastic, and metal. Acoustic treatments such as coatings, textiles and foams are used within the cab for aesthetics but also to mediate undesired noise. To develop effective designs for the cab to combat noise, accurate tools for measurement, and predictive methods for sound transmission loss are needed. This paper focuses on Sound Transmission Loss (STL) of the rear upper panel of a cab used in agriculture machines. Results from CAE based tools such as Statistical Energy Analysis (SEA), Finite Element Analysis (FEA) and Hybrid FE-SEA methods are compared to measurements. The panel studied included features such as curvature, deep drawn beads with a glass window and a damping coating. The simulation results are refined by incorporating methods for accurate modeling of ribs stiffness, curvature effect and radiation efficiency by synthetic modal approach.

Structure-borne inputs to hybrid FEA/SEA models could have significant effects on the model prediction accuracy. The purpose of this work was to obtain the structure-borne noise (SBN) inputs using a simplified transfer path analysis (TPA) and identify the significance of the structure-borne and airborne contributions to the spectator sound power of an engine with enclosure for future modeling references. Force inputs to the enclosure from the engine were obtained and used as inputs to a hybrid engine enclosure model for sound prediction.

Caterpillar uses heat treatment to enhance the properties of a significant number of parts. Traditional heat treat process optimization is both time consuming and expensive when done by empirical methods. This paper describes a computer simulation of the heat treatment process, developed by Caterpillar, based upon finite element analysis. This approach combines thermal, microstructural, and stress analysis to accurately model material transformation during quenching. Examples are presented to illustrate the program.

A nonlinear, three-dimensional finite element analysis of the cylinder head gasket joint has been developed to allow accurate prediction of global and local joint behavior during engine operation. Nonlinear material properties and load cases that simulate full cycle engine operation are the analysis foundation. The three-dimensional, nonlinear, full-cycle simulation accurately predicts cylinder head gasket joint response to assembly, thermal, and cylinder pressure loading. Predictions correlate well with measured engine test data. Analysis results include local pressure distribution and global load splits. Insight into joint loading and an improved understanding of overall joint behavior provide the basis for informed design and development decisions.

Operator noise is an important aspect for noise and vibration of off-highway vehicles and a quieter cab is critical for the operator comfort. The noise level inside the cab is influenced by structural and acoustic transfer paths. In this paper, we used hybrid FE-SEA approach to consider both structural and acoustic transfer path as FEM and SEA methods individually face limitations in high and low frequencies respectively. A hybrid FE-SEA cab model was built to predict the structural and acoustic transfer functions. The analysis model was built with the systematic approach validated at each step with the laboratory test results. For the structural transfer function, structural excitations were applied at four cab mount locations and accelerations at various locations on the cab were validated. For the acoustic transfer function, the cab was excited with the volume velocity source inside the cab and sound power output of various panels were calculated and compared to the test results.

Since the advent of P/M technology as a near net shape production process, millions of mechanical components of various shapes and sizes have been produced. Although P/M continues to be one of the fast growing shaping processes, it suffers from the inability to produce intricate geometry's such as internal tapers, threads or recesses perpendicular to pressing direction. In such cases application of machining as a secondary forming operation becomes the preferred alternative. However, machining of P/M parts due to their inherent porosity is known to decrease tool life and increase tool chatter and vibration. Consequently, several attempts have been made to improve the machinability of P/M materials by either addition of machinability enhancing elements such as sulfur, calcium, tellurium, selenium, etc., or by resin impregnation of P/M parts.

The induction hardening process involves a complex interaction of electromagnetic heating, rapid cooling, metallurgical phase transformations, and mechanical behavior. Many factors including induction coil design, power, frequency, scanning velocity, workpiece geometry, material chemistry, and quench severity determine a process outcome. This paper demonstrates an effective application of a numerical analysis tool for understanding of induction hardening. First, an overview of the Caterpillar induction simulation tool is briefly discussed. Then, several important features of the model development are examined. Finally, two examples illustrating the use of the computer simulation tool for solving induction-hardening problems related to cracking and distortion are presented. These examples demonstrate the tool's ability to simulate changes in process parameters and latitude of modeling steel or cast iron.

Finite Element Analysis (FEA)-based structural simulations are typically used to assess the durability of automotive components. Many parts experience vibration in use, and resonance effects are directly linked to many structural problems. In this case, dynamics must be included in the structural analysis. Dynamic FEA can be more realistic than static analysis, but it requires knowledge of additional characteristics such as mass and damping. Damping is an important property when performing dynamic FEA, whether transient or steady state dynamics, as it governs the magnitude of the dynamic stress response and hence durability. Unfortunately the importance of damping is often overlooked; sometimes a default damping value is erroneously assumed for all modes. Errors in damping lead to errors in the stress response, which in turn lead to significant changes in the fatigue life estimates.

Lubricating oil affects the performance of friction materials in transmission, steering and brake systems. The TO-2 Test measured friction retention characteristics of lubricating oils used with sintered bronze friction discs. This paper introduces a new friction performance test for drive train lubricants that will be used to support Caterpillar's new transmission and drive train fluid requirements, TO-4, which measures static and dynamic friction, wear, and energy capacity for six friction materials, and replaces the TO-2 test. The new test device to be introduced is an oil cooled, single-faced clutch in the Link Engineering Co. M1158 Oil/Friction Test Machine.

The fatigue properties of gray cast iron are presented. Included in these properties are monotonic tension and compression data and cyclic strain control fatigue data. Estimations of fatigue properties determined from the measured fatigue data are compared to predicted fatigue properties based on static properties. Samples with average hardnesses of 171 and 213 Bhn iron were tested and the results compared. The results of this investigation revealed that the strain amplitude cycles-to-failure plot of gray cast iron was independent of hardness of the iron.

The demands on improving the noise, vibration and harshness of the golf mowing machines are growing rapidly. Low frequency vibrations at the human touchpoints are one of the important factors leading to the discomfort of operators on these machines. In the present work, low frequency vibrations experienced by the operator of the golf mowing machine are reduced using finite element analysis (FEA) and validated by a physical test. Initially, testing observed high vibration at the command arm, where some of the operating controls are placed. FEA was carried out on a frame level assembly and the design was iterated to affect these vibration levels. The golf mowing machine considered in this work is powered by a gasoline engine, which is the source of excitation in the current scenario. The operational forces of the engine were measured by using blocked-force transfer path analysis at its mounts. The modal frequency response analysis used these calculated forces as an input excitation.

Numerical models are used in this study to investigate the oil flow and heat transfer in the piston gallery of a diesel engine. An experiment is set up to validate the numerical models. In the experiment a fixed, but adjustable steel plate is instrumented and pre-heated to a certain temperature. The oil is injected vertically upwards from an underneath injector and impinges on the bottom of the plate. The reduction of the plate temperature is recorded by the thermocouples pre-mounted in the plate. The numerical models are used to predict the temperature history at the thermocouple locations and validated with the experimental data. After the rig model validation, the numerical models are applied to evaluate the oil sloshing and heat transfer in the piston gallery. The piston motion is modeled by a dynamic mesh model, and the oil sloshing is modeled by the VOF (volume of fluid) multiphase model.

RADAR Sensors are going to be an integral part of autonomous vehicles. One of the main objectives of these sensors in autonomous vehicles is to get the Doppler range profile for surrounding traffic. In this paper, we use a similar RADAR for ground speed sensing in the off-highway scenario. There are several challenges in integrating the RADAR sensor with vehicles such as sensor position from ground, location on vehicle, electromagnetic interference with other electronic devices, enclosure design etc. Ground conditions and properties are also critical in the off-highway scenario for speed sensing. We propose to use the physics based electromagnetic field solvers to understand and mitigate some of these challenges and speed up the design. Electromagnetic field solvers tend to scale poorly with distance of propagation, especially in 3D modeling.