Search Results

The validation of vehicle aerodynamic simulation results to wind tunnel test results and simulation accuracy improvement attract considerable attention of many automotive manufacturers. In order to improve the simulation accuracy, a simulation model of the ground effects simulation system of the aerodynamic wind tunnel of the Shanghai Automotive Wind Tunnel Center was built. The model includes the scoop, the distributed suction, the tangential blowing, the moving belt and the wheel belts. The simulated boundary layer profile and the pressure distribution agree well with test results. The baseline model and multiple design changes of the new Buick Excelle GT are simulated. The simulation results agree very well with test results.

Fuel efficiency for tractor/trailer combinations continues to be a key area of focus for manufacturers and suppliers in the commercial vehicle industry. Improved fuel economy of vehicles in transit can be achieved through reductions in aerodynamic drag, tire rolling resistance, and driveline losses. Fuel economy can also be increased by improving the efficiency of the thermal to mechanical energy conversion of the engine. One specific approach to improving the thermal efficiency of the engine is to implement a waste heat recovery (WHR) system that captures engine exhaust heat and converts this heat into useful mechanical power through use of a power fluid turbine expander. Several heat exchangers are required for this Rankine-based WHR system to collect and reject the waste heat before and after the turbine expander. The WHR condenser, which is the heat rejection component of this system, can be an additional part of the front-end cooling module.

A challenge for the aerodynamic optimization of trucks is the limited availability of wind tunnels for testing full scale trucks. FAW wants to introduce a development process which is mainly based on CFD simulation in combination with some limited amount of wind tunnel testing. While maturity of CFD simulation for truck aerodynamics has been demonstrated in recent years, a complete validation is still required before committing to a particular process. A 70% scale model is built for testing in the Shanghai Automotive Wind Tunnel Center (SAWTC). Drag and surface pressures are measured for providing a good basis for comparison to the simulation results. The simulations are performed for the truck in the open road driving condition as well as in an initial digital model of the aerodynamic wind tunnel of SAWTC. A full size truck is also simulated in the open road driving condition to understand the scaling effect.

The implementation of an advanced process for the aerodynamic development of cab-over type heavy trucks at China FAW Group Corporation (FAW) requires a rigorous validation of the tools employed in this process. The final objective of the aerodynamic optimization of a heavy truck is the reduction of the fuel consumption. The aerodynamic drag of a heavy truck contributes up to 50% of the overall resistance and thus fuel consumption. An accurate prediction of the aerodynamic drag under real world driving conditions is therefore very important. Tools used for the aerodynamic development of heavy trucks include Computational Fluid Dynamics (CFD), wind tunnels and track and road testing methods. CFD and wind tunnels are of particular importance in the early phase development.

A correlation study was performed between static wind tunnel testing and computational fluid dynamics (CFD) for a small hatchback vehicle, with the intent of evaluating a variety of different wheel and tire designs for aerodynamic forces. This was the first step of a broader study to develop a tool for assessing wheel and tire designs with real world (rolling road) conditions. It was discovered that better correlation could be achieved when actual tire scan data was used versus traditional smooth (CAD) tire geometry. This paper details the process involved in achieving the best correlation of the CFD prediction with experimental results, and describes the steps taken to include the most accurate geometry possible, including photogrammetry scans of an actual tire that was tested, and the level of meshing detail utilized to capture the fluid effects of the tire detail.

A vehicle on the road encounters an unsteady flow due to turbulence in the natural wind, the unsteady wakes from other vehicles and as a result of traversing through the stationary wakes of road side obstacles. There is increasing concern about potential differences in aerodynamic behaviour measured in steady flow wind tunnel conditions and that which occurs for vehicles on the road. It is possible to introduce turbulence into the wind tunnel environment (e.g. by developing active turbulence generators) but on-road turbulence is wide ranging in terms of both its intensity and frequency and it would be beneficial to better understand what aspects of the turbulence are of greatest importance to the aerodynamic performance of vehicles. There has been significant recent work on the characterisation of turbulent airflow relevant to road vehicles. The simulation of this time-varying airflow is now becoming possible in wind tunnels and in CFD.

Aerodynamic efficiency plays an increasingly important role in the automotive industry, as the push for increased fuel economy becomes a larger factor in the engineering and design process. Longitudinal drag is used as the primary measure of aerodynamic performance, usually cited as the coefficient of drag (CD). This drag is created mostly by the body shape of the vehicle, but the wheel and tire system also contributes a significant portion. In addition to the longitudinal drag created by the body and wheels, rotational drag can add an appreciable amount of aerodynamic resistance to the vehicle as well. Reducing power consumption is an especially vital aspect in electric vehicle (EV) design. As the world's first luxury electric sedan, the Tesla Model S combines a premium driving experience with an electric drivetrain package that allows for unique solutions to many vehicle subsystems.

The Tesla Motors Model S has been designed from a clean sheet of paper to prove that no compromises to a desirable aesthetic style and world class driving experience are necessary in order to be energy efficient. Aerodynamic optimization is a major contributor to the overall efficiency of an electric vehicle and the close integration of the Design and Engineering groups at Tesla Motors was specifically arranged to process design iterations quickly and enable the fully informed development of the exterior surfaces at a very rapid pace. Clear communication and a working appreciation of each other's priorities were vital to this collaboration and underpinning this was extensive use of the powerful analysis and visualization capabilities of CFD. CFD was used to identify and effectively communicate the nature of beneficial and detrimental design features and to find ways to enhance or ameliorate them accordingly.

The development of a new Dongfeng Heavy truck had very strict targets for fuel consumption. As the aerodynamic drag plays a crucial role for the fuel consumption, a low drag value had to be achieved. It was therefore essential to include evaluation and optimization of the aerodynamics in the development process. Because wind tunnel facilities were not available, the complete aerodynamics development was based on digital simulation. The major portion of the aerodynamic optimization was carried out during the styling phase where mirrors, sun visor, front bumper and aero devices were optimized for drag reduction. For optimizing corner vanes and mud guards, self-soiling from the wheel spray was included in the analysis. The aero results did also show that cooling air flow rates are sufficiently high to ensure proper cooling. During the detailed engineering phase an increase of the drag above the target required further optimization work to finally reach the target.

Wind noise is a significant source of interior noise in automobiles at cruising conditions, potentially creating dissatisfaction with vehicle quality. While wind noise contributions at higher frequencies usually originate with transmission through greenhouse panels and sealing, the contribution coming from the underbody area often dominates the interior noise spectrum at lower frequencies. Continued pressure to reduce fuel consumption in new designs is causing more emphasis on aerodynamic performance, to reduce drag by careful management of underbody airflow at cruise. Simulation of this airflow by Computational Fluid Dynamics (CFD) tools allows early optimization of underbody shapes before expensive hardware prototypes are feasible. By combining unsteady CFD-predicted loads on the underbody panels with a structural acoustic model of the vehicle, underbody wind noise transmission could be considered in the early design phases.

Numerical simulation of aerodynamics for vehicle development is used to meet a wide range of performance targets, including aerodynamic drag for fuel efficiency, cooling flow rates, and aerodynamic lift for vehicle handling. The aerodynamic flow field can also be used to compute the advection of small particles such as water droplets, dust, dirt, sand, etc., released into the flow domain, including the effects of mass, gravity, and the forces acting on the particles by the airflow. Previous efforts in this topic have considered the water sprays ejected by rotating wheels when driving on a wet road. The road spray carries dirt particles and can obscure the side and rear glazing. In this study, road sprays are considered in which the effects of additional water droplets resulting from splashing and dripping of particles from the wheel house and rear under body are added to help understand the patterns of dirt film accumulation on the side glass and rear glass.

Ground transportation industry contributes to about 14% of the global CO2 emissions. Therefore, any effort in reducing global CO2 needs to include the design of cleaner and more energy efficient vehicles. Their design needs to be optimized for the real-world conditions. Using wind tunnels that can only reproduce idealized conditions quite often does not translate into real-world on-road CO2 reduction and improved energy efficiency. Several recent studies found that very rarely can the real-world environment be represented by turbulence-free conditions simulated in wind tunnels. The real-world conditions consist of both transversal flow velocity component (causing an oncoming yaw flow) as well as large-scale turbulent fluctuations, with length scales of up to many times the size of a vehicle. The study presented in this paper shows how the realistic wind affects the aerodynamics of the vehicle.

A study was performed to determine the fluid structure interaction (FSI) for a prototype truck hood for transient aerodynamic loads. The growing need to make vehicle panels lighter to enhance the fuel economy of vehicles has made hood panels more prone to deformation and vibration from aerodynamic loads. Moreover, as global pedestrian crash standards become more stringent to provide safer front end designs to minimize injuries to head and leg, automotive manufacturers are being required to design flexible hoods that crush significantly more than the present designs to absorb the crash energy better. These flexible designs lead to potentially undesirable deformations and/or vibration behavior of the hood at typical highway speeds.

The engineering process in the development of commercial vehicles is facing more and more stringent emission regulations while at the same time the market demands for better performance but with lower fuel consumption and higher reliability. Respective targets require better utilization of existing or even higher engine cooling capacity and optimization of aerodynamic performance for reduced drag. In order to aid on achieving both goals, special attention should be paid on understanding both external and under hood flow structures. This paper describes an optimization study for reducing aerodynamic drag and increasing engine cooling performance conducted on a Light Truck at Jiangling Motors Corporation (JMC). The approach is using simulation based on a LBM solver coupled with a heat exchanger model. Such methodology was used to predict both aerodynamic and cooling characteristics and help highlighting potential areas for improvement.

The high cost and competitive nature of automotive product development necessitates the search for less expensive and faster methods of predicting vehicle performance. Continual improvements in High Performance Computing (HPC) and new computational schemes allow for the digital evaluation of vehicle comfort parameters including wind noise. Recently, the commercially available Computational Fluid Dynamics (CFD) code PowerFlow, was evaluated for its accuracy in predicting wind noise generated by an external automotive tow mirror. This was accomplished by running simulations of several mirror configurations, choosing the quietest mirror based on the predicted performance, prototyping it, and finally, confirming the prediction with noise measurements taken in an aeroacoustic wind tunnel. Two testing methods, beam-forming and direct noise measurements, were employed to correlate the physical data with itself before correlating with simulation.

Water accumulating on a vehicle's wind screen, driven over the A-pillar by a combination of aerodynamic forces and the action of the windscreen wipers, can be a significant impediment to driver vision. Surface water film, or streams, persisting in key vision areas of the side glass can impair the drivers' ability to see clearly through to the door mirror, and laterally onto junctions. Common countermeasures include: water management channels and hydrophobic glass coatings. Water management channels have both design and wind noise implications. Hydrophobic coatings entail significant cost. In order to manage this design optimisation issue a water film and wiper effect model has been developed in collaboration with Jaguar Land Rover, extending the capabilities of the PowerFLOW CFD software. This is complimented by a wind-tunnel based test method for development and validation. The paper presents the progress made to date.

Recent regulations on greenhouse gas (GHG) emission standards for heavy duty vehicles have prompted government agencies to standardize procedures to assess aerodynamic performance of Class 8 tractor-trailers. The coastdown test procedure is the primary reference method to assess vehicle drag and other valid alternatives include wind tunnel testing and computational fluid dynamics (CFD) simulations. While there have been many published studies comparing results between simulations and wind tunnel testing, it is less well understood how to compare results with coastdown testing. Both the wind tunnel and simulation directly measure aerodynamic drag forces in controlled conditions, while coastdown testing is conducted in an open road environment, aerodynamic forces are calculated from a road load equation, and variable wind and vehicle speed introduce additional complexity.

Pickup trucks are designed with a taller ride height and a larger tire envelope compared to other vehicle types given the duty cycle and environment they operate in. These differences play an important role in the flow field around spinning wheels and tires and their interactions with the vehicle body. From an aerodynamics perspective, understanding and managing this flow field are critical for drag reduction, wheel design, and brake cooling. Furthermore, the validation of numerical simulation methodology is essential for a systematic approach to aerodynamically efficient wheel design as a standard practice of vehicle design. This paper presents a correlation the near-wheel flow field for both front and rear spinning wheels with two different wheel designs for a Ram Quad Cab pick-up truck with moving ground. Twelve-hole probe experimental data obtained in a wind tunnel with a full width belt system are compared to the predictions of numerical simulations.

The purpose of this paper is to describe some of the technology behind the Lattice Boltzmann approach to exterior airflow simulations as incorporated into the commercial CFD code, PowerFLOW®. The fundamental approach used is the Lattice Boltzmann Method (LBM) coupled with both a turbulence model to recover the dissipation of sub-grid eddy scales and a wall model to allow reduced resolution in the near-wall region. A description of LBM and both models is given. Comparisons to methods that directly solve the Navier-Stokes equations, such as finite volume or finite element methods (hereafter, collectively referred to as RANS methods) are also presented. A demonstration of the technology is presented by comparing numerical simulations with extensive experimental test data on Ford's standard calibration models. These models were originally described in SAE paper 940323 [1].

The DrivAer model, a detailed generic open source vehicle geometry, was introduced a few years ago and accepted widely from industry and academia for research in the field of automotive aerodynamics. This paper presents the evaluation of the aerodynamic properties of the 25% scale DrivAer model in both, CFD and in wind tunnel experiment. The results not only include aerodynamic drag and lift but also provide detailed investigations of the flow field around the vehicle. In addition to the available geometries of the DrivAer model, individual changes were introduced created by morphing the geometry of the baseline model. A good correlation between CFD and experiment could be achieved by using a CFD setup including the geometry of the wind tunnel test section. The results give insight into the aerodynamics of the DrivAer model and lead to a better understanding of the flow around the vehicle.